Influence of activator on the strength and drying shrinkage of alkali-activated slag mortar

The development of new binders, as an alternative to traditional cement, by the alkaline activation of industrial by-products (i.e. ground granulated slag and fly ash) is an ongoing research topic in the scientific community [Puertas F, Amat T, Jimenez AF, Vazquez T. Mechanical and durable behaviour of alkaline cement mortars reinforced with polypropylene fibres. Cem Concr Res 2003;33(12): 2031–6]. The aim of this study was to investigate the feasibility of using and alkaline activated ground Turkish slag to produce a mortar without Portland cement (PC).Following the characterization of the slag, mortar specimens made with alkali-activated slag were prepared. Three different activators were used: liquid sodium silicate (LSS), sodium hydroxide (SH) and sodium carbonate (SC) at different sodium concentrations. Compressive and flexural tensile strength of alkali-activated slag mortar was measured at 7-days, 28-days and 3-months. Drying shrinkage of the mortar was measured up to 6-months. Setting times of the alkali-activated slag paste and PC paste were also measured.Setting times of LSS and SH activated slag pastes were found to be much slower than the setting time of PC paste. However, slag paste activated with SC showed similar setting properties to PC paste.LSS, SH and SC activated slag mortar developed 81, 29, and 36 MPa maximum compressive strengths, and 6.8, 3.8, and 5.3 MPa maximum flexural tensile strengths at 28-days. PC mortar developed 33 MPa compressive strength and 5.2 MPa flexural tensile strength. LSS and SH activated slag mortars were found to be more brittle than SC activated slag and PC mortars.Slag mortar made with LSS had a high drying shrinkage, up to six times that of PC mortar. Similarly, slag mortar made with SH had a shrinkage up to three times that of PC mortar. However, SC activated slag mortar had a lower or comparable shrinkage to PC mortar. Therefore, the use of SC as an activator for slag mortar is recommended, since it results in adequate strength, similar setting times to PC mortar and comparable or lower shrinkage.     

Soil productivity analysis based on a fuzzy logic system

BACKGROUND: Maintaining soil productivity is essential if agriculture production systems are to be sustainable. However, there is a paucity of tools for measurement for the purpose of understanding changes in soil productivity. Fuzzy logic‐based analysis offers this possibility. It is a new method on the evaluation of soil productivity in Turkey and even in the world. RESULTS: Values for pH, salinity, carbonate and organic matter were entered into the system as input variables so as to obtain soil productivity as the output. After the membership functions related to input and output were determined, rules were created. Then, the fuzzy logic system was applied separately to pH, salinity, lime and organic matter values of different soil types present in the Kocaeli region with the aim of obtaining corresponding fuzzy values. Thus, soil productivity profiles of the region were deciphered. CONCLUSION: Organic matter levels in the study field remained below 30 g kg^?1 and varied between 22 and 28 g kg^?1. Productivity values were obtained as a percentage and varied between 16.9% and 18.1%. The lime content of the study soils varied in the range of 33–88 g kg^?1. Average totals for salt values of the field changed between 0.58 and 0.77 g kg^?1. Copyright © 2010 Society of Chemical Industry     

The long‐term effects of arteriovenous fistula creation on the development of pulmonary hypertension in hemodialysis patients

The aim of this prospective study was to evaluate long‐term effects of arteriovenous fistula (AVF) on the development of pulmonary arterial hypertension (PAH) and the relationship between blood flow rate of AVF and pulmonary artery pressure (PAP) in the patients with end‐stage renal disease (ESRD). This prospective study was performed in 20 patients with ESRD. Before an AVF was surgically created for hemodialysis, the patients were evaluated by echocardiography. Then, an AVF was surgically created in all patients. After mean 23.50 ± 2.25 months, the second evaluation was performed by echocardiography. Also, the blood flow rate of AVF was measured at the second echocardiographic evaluation. Pulmonary arterial hypertension was defined as a systolic PAP above 35 mmHg at rest. Mean age of 20 patients with ESRD was 55.05 ± 13.64 years; 11 of 20 patients were males. Pulmonary arterial hypertension was detected in 6 (30%) patients before AVF creation and in 4 (20%) patients after AVF creation. Systolic PAP value was meaningfully lower after AVF creation than before AVF creation (29.95 ± 10.26 mmHg vs. 35.35 ± 7.86 mmHg, respectively, P: 0.047). However, there was no significant difference between 2 time periods in terms of presence of PAH (P>0.05). Pulmonary artery pressure did not correlate with blood flow rate of AVF and duration after AVF creation (P>0.05). In hemodialysis patients, a surgically created AVF has no significant effect on the development of PAH within a long‐term period. Similarly, blood flow rate of AVF also did not affect remarkably systolic PAP within the long‐term period.     

Wear behavior of a crankshaft journal bearing manufactured by powder spraying

A new crankshaft bearing material that can be an alternative to the traditional material has been improved and its wear behavior studied experimentally. Crankshaft main bearings are subjected to various stresses. A new material supposed to be adapted these operating conditions was designed composing of Pb–Sn–Cu–ZrO₂ and manufactured by HVOF spraying technique. Wear behavior of the bearing was tested with the simulation of real operating conditions. An original bearing was used for comparison. After a trial of 500 h, the weight losses were measured. SEM micrographs of both original and new bearings were examined. The effect of microhardness was discussed. The new composition was seen as promising as a bearing material for automotive engines.     

New organic semiconductor materials: electrical conductivity,thermal properties and application of voltage‐controlled negative resistance device of poly[(2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid)‐co‐(maleic acid)]

BACKGROUND: Electrical conductivity, photoconductivity, voltage‐controlled negative resistance and thermal properties of copolymers of 2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid and maleic acid were investigated in order to obtain new organic semiconductors. RESULTS: The room temperature conductivity of three different copolymers was found to be in the range 1.28 × 10^?8 ? 1.20 × 10^?7 S cm^?1. The dark‐ and photo‐current‐voltage characteristics indicate that the copolymers exhibit voltage‐controlled differential negative resistance behaviour. The electrical conductivity of the polymers increases by photo‐illumination, suggesting that the polymers exhibit photoconductivity. The width of the exponential tail in the forbidden band gap of the three polymers was determined via the transient photocurrent technique and E₀ values were in the range 34.4–36.49 meV. CONCLUSION: The results suggest that the copolymers could be used as organic semiconductor materials. Copyright © 2007 Society of Chemical Industry     

Constructability Analysis in the Design Firm

The timely execution of a construction project is very important to the owner, who makes plans and commitments on the basis of the project’s anticipated completion date. Failure of design professionals to consider how a builder will implement the design can result in scheduling problems, delays, and disputes during the construction process. Constructability of design is a subjective scale that depends basically on a number of interdependent project-related factors. Many design firms have a formal (explicit) constructability program that is launched as early as the conceptual planning stage of the project. This research examines design professionals’ efforts to pursue constructability and provides recommendations for performing constructability reviews in an efficient and effective manner.     

Numerical prediction of three-dimensional fiber orientation in Hele-Shaw flows

A numerical technique is developed to determine the three-dimensional fiber orientation in complex flows. The fiber orientation state is specified in terms of orientation tensors, which are used in several constitutive models. This method is applied to quasi-steady state Hele-Shaw flows in order to predict the flow-induced fiber orientation during injection molding at zero volume fraction limit. At the inlet, a number of fibers are introduced at a specified rate into the flow and each fiber location is traced during the mold filling. Along these determined paths, the independent components of fourth order orientation tensors are solved, describing the orientation state. The numerical grid generation technique, which is suitable for complex mold shapes, is employed for the flow solution. Orientation ellipsoids are calculated from the second order tensors and are used to present the fiber orientation results. The numerical solutions are obtained for channel and converging flows. Planar, longitudinal, and transverse orientation results are generated from the orthogonal projections of the orientation ellipsoids.     

3-D micro-ceramic components from hydrothermally processed carbon nanotube–boehmite powders by electrophoretic deposition

Boehmite/multi-wall carbon nanotube (MWCNT) composite powders were prepared by hydrothermal processing. Starting chemical of aluminum acetate powders (2Al(OH)(C₂H₃O₂)₂) and MWCNTs were mixed for the formation of stoichiometric boehmite powders in an attempt to synthesize MWCNT-reinforced boehmite nano-powders via hydrothermal synthesis at 200 °C for 2 h. Kinetically stable suspensions of MWCNT–boehmite composite powders were prepared and subsequently electrophoretic deposition (EPD) was applied to obtain complex shape products in the form of micro-gears. It is shown that the EPD technique is a powerful tool to manufacture small components in a short time. Detail TEM observations also indicated that hydrothermal processing provides an ideal environment to obtain homogeneous mixtures of MWCNT–boehmite powders due to effective surface functionalization of MWCNTs under hydrothermal conditions.