Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

自然伽马能谱资料预处理程序PRECNG在塔河油田的应用

PRECNG是自然伽玛能谱资料预处理程序，是一种转换处理256道CSNG高能谱数据和总伽马的方法。文章阐述了处理模型的建立和实现，并介绍了该程序在实际测井中的应用情况。     

改性纳米TiO2光催化降解苯酚活性的研究

在装有紫外光的光催化反应器中，用锐钛型纳米TiO2为光催化剂，进行了苯酚水溶液的光催化降解性能的研究。考察了溶液的pH值、纳米TiO2用量、镍（Ni^2＋）掺杂量、苯酚的初始质量浓度等因素对苯酚水溶液光催化降解过程的影响。结果表明，在pH值为7时，苯酚水溶液的降解率达95％以上，强酸和强碱条件均不利于苯酚的降解。当TiO2用量为50mg，UV辐照40min时，200mL质量浓度为50mg／L的苯酚水溶液的降解率为96．3％；当TiO2用量为150mg，UV辐照60min时，200mL质量浓度100mg／L的苯酚水溶液的降解率为95．8％。镍掺杂增加了TiO2的光催化活性，用质量分数为10％的二氯化镍水溶液掺杂制备的复合光催化剂，苯酚水溶液的降解率比未掺杂时增加13．6％。     

新氢压缩机投用Hydro COM系统对生产及工艺过程控制的影响

中国石油化工股份有限公司燕山分公司中压加氢裂化装置新氢压缩机投用了Hydro COM无级调量系统,其优点主要有三个:新氢压缩机没有了氢气返回,节省了大量电能;机组的运行稳定性有了明显改善;优化了反应系统的压力控制方案,使反应系统压力控制相对平稳.     

XMAC纵波时差高分辨率处理方法

在充分调研阵列声波测井分波提取方法的基础上，针对阿特拉斯公司的交叉多极子阵列声波测井（XMACⅡ）提供的单极波形信息，研究纵波时差提取及高分辨率处理方法。首先利用相关-互功谱法高精度地提取纵波时差，然后针对XMACⅡ仪器的接收阵列，研究组合子阵列的方法，形成共发射子阵列和共接收子阵列，最后利用子阵列对提取的纵波时差做高分辨率处理。处理现场实际测井资料，并将高分辨率处理成果与引进的eXpress软件处理成果、实测的国产高分辨率声波（纵波）测井曲线及岩心纵波时差对比分析，表明该方法提取的纵波时差曲线的纵向分辨率有很大提高，时差计算准确可靠，提取的单极纵波时差与国产高分辨率声波时差及岩心纵波时差的平均相对误差均小于7%。该方法具有较高的实用价值和广阔的应用前景。     

基于两层均匀媒质的GPEN SAR地下目标成像方法及其性能分析

地表穿透合成孔径雷达(Ground PENetration SAR,GPEN SAR)为了探测掩埋在地下的目标,通常工作在多层媒质的环境中。传统成像模型是建立在同一均匀媒质的假设上,不再适合于GPEN SAR的实际情况。本文首先建立了两层分区均匀媒质中的成像模型,然后利用后向投影(BP)算法定量分析了成像几何参数、土壤参数等对成像的影响,进而提出了一种修正的后向投影(MBP)算法。MBP算法不仅能够校正两层分区均匀媒质对成像定位的影响,还能估计目标的掩埋深度,提供目标三维位置坐标。仿真结果验证了MBP算法在不同信噪比环境下,对多目标的三维定位精度能满足实际的需要。     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

MULTICARRIER DS—CDMA WITH ADAPTIVE MODULATION AND POWER ALLOCATION

Adaptive modulation and power allocation is introduced into the multicarrier DSCDMA system to improve the system performance and bandwidth efficiency.First,the system design appropriate for adaptive modulation and power allocation is given,then the algorithm of adaptive modulation and power allocation is applied.Simulation results demonstrate great performance improvement compared with the fixed modulated one.