Chalcogenide Glasses Based on Germanium Disulfide for Second Harmonic Generation

High second‐order susceptibilities are created by thermal poling in bulk germanium disulfide based chalcogenide glasses. Experimental conditions of the poling treatment (temperature, voltage, time) were optimized for each glass composition. The second‐order nonlinear signals were recorded by using the Maker fringes experiment and a second‐order coefficient χ⁽²⁾ up to 8 pm V^–1 was measured in the Ge₂₅Sb₁₀S₆₅ glass. This value is obtained using a simulation based on accurate knowledge of the thickness of the nonlinear layer. Two mechanisms are proposed to explain the creation of a nonlinear layer under the anode: the formation and the migration of charged defects towards the anode may mainly occur in Ge₂₀Ga₅Sb₁₀S₆₅ and Ge₂₅Ga₅S₇₀ glasses, whereas the migration of Na⁺ ions towards the cathode may be responsible for the accumulation of negative charges under the anode in Ge₃₃S₆₇ and Ge₂₅Sb₁₀S₆₅ glasses. Different electronic conductivity behaviors seem to be at the origin of the phenomenon. In parallel, the potential effect of the poling treatment on the structural and electronic properties is studied using Raman spectroscopy and secondary ion mass spectroscopy measurements.     

钢包炉(LF)预熔精炼渣的研究

预熔精炼渣具有成分均匀，性能稳定，储存时不吸水等特点，钢包炉中使用预熔精炼渣时成渣均匀且速度快，具有较强的吸附钢中非金属夹杂的能力。综合脱硫率高等冶金效果。有显著净化钢液作用。     

基于运动矢量分布特征的半像素快速搜索算法

针对MPEG-4视频编码中半像素全搜索方法运算量较大的缺点,提出一种基于运动矢量分布特征的快速半像素运动矢量搜索算法。试验表明最佳半像素运动矢量的分布具有一定的规律,即大多数的运动矢量分布在水平或垂直两个共扼方向上。因此在满足一定条件的前提下水平和垂直方向上的运动矢量被优先搜索,其次搜索其余的点。仿真结果表明本算法可以使半像素平均搜索点数减少71%,而编码质量和码流长度并没有明显降低或增加。     

Water bamboo husk reinforced poly(lactic acid) green composites

The water bamboo husk is one of major agricultural wastes in Taiwan. In this study, the powder obtained from the water bamboo husk was added to poly(lactic acid) (PLA) to form novel reinforced biodegradable composites. Morphologies, mechanical properties, and heat resistance of these water bamboo powder reinforced composites were investigated. The results indicate that the char yields were increased as plant powder was incorporated to PLA. In addition, the mechanical properties were also enhanced due to the addition of powders. The increments of storage moduli of PLA were about 50–200%. Moreover, the increments of loss moduli of PLA were about 70–200%. On the other hand, the T_g of PLA was slightly decreased by the addition of powder, and this may improve the brittle characteristics of PLA. Furthermore, this type of reinforced PLA would be more environmental friendly than the artificial additive‐reinforced one. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Oil yield and compressibility modeling during microscale expression: Criteria for linseed breeding

Seven linseed varieties were harvested at seven times before complete maturity. Microscale oilseed expressions were subsequently carried out on it. A pressure of 10 MPa was applied for 1 h under uniaxial stress. The results were characterized in terms of oil, water and mucilage content, harvest date and oil yield. The piston displacement versus time (creep curves) was described by a four‐Kelvin‐Voigt elements viscoelastic model. Parameters were derived from the model, such as the mechanical properties of seeds (compressibility moduli), showing that the viscoelastic model fits well the experimental data (R² ≈ 0.999). The modeling parameters were combined with some biochemical data in order to predict the kinetics of oil extraction.     

Studies of substrate specificities of lipases from different sources

Although lipases are widely applied in a wide variety of reactions, available information on the factors that are responsible for the substrate specificities of lipases from different sources is scarce. In this paper, nine lipase‐producing microorganism strains were isolated from oil‐containing samples. The properties of these enzymes, including pH optima, temperature optima, thermal stability, and pH stability, vary significantly with the different sources from which these lipases were isolated. The substrate specificities of the nine lipases, including fatty acid and positional specificities, were also studied. The fatty acid specificities of the nine lipases were observably different toward 15 substrates with different carbon chain lengths, different saturation degrees and different side chains. The lipases from S₃ Penicillium citrinum (PCL), MJ₁ Aspergillus niger (ANL), MJ₂ Aspergillus oryzae (AOL), YM Bacillus coughing (BCL), S₉ Geotrichum candidum (GCL), and S₁₁ Candida lypolytica (CLL) showed the strongest specificities to short‐chain esters, and the other lipases showed strong selectivity for medium‐ or long‐chain and branched esters. The positional specificities were examined by analyzing the hydrolytic products of triolein catalyzed by the nine lipases, using TLC. The lipases can be mainly classified into two groups by their specificities for the ester bond at position 2 of triglycerides; one group can selectively hydrolyze the ester bond at position 2 of the triglycerides, the other group cannot. All these nine lipases were divided into four groups by hierarchical clustering analysis on the basis of the results of fatty acid and positional specificities.