An improved Gaussian approximation for probability of bit-erroranalysis of asynchronous bandlimited DS-CDMA systems with BPSK spreading

This paper analyzes probability of bit-error (P_e) performance of asynchronous bandlimited direct-sequence code-division multiple-access systems with binary phase-shift keying spreading. The two present methods of P_e analysis under bandwidth-efficient pulse shaping: the often-cited standard Gaussian approximation and the characteristic function (CF) method suffer from either a low accuracy in regions of low P_e (< 10^-3) or a prohibitively large computational complexity. The paper presents an alternate method of P_e analysis with moderate computational complexity and high accuracy based on a key observation. A sequence of chip decision statistics (whose sum yields a bit statistic) forms a stationary, m-dependent sequence when conditioned on the chip delay and phase offset of each interfering signal. This observation permits the generalization of the improved Gaussian approximation previously derived for the rectangular pulse and the derivation of a numerically efficient approximation based on the CF method. Numerical examples of systems using the square-root raised-cosine and IS-95 pulses illustrate THE P _e performance, user capacity and the accuracy of the proposed method     

Survival of Salmonella typhimurium on Sterile Ground Chicken Breast Patties After Washing with Salt and Phosphates and During Refrigerated and Frozen Storage

ABSTRACT: This study investigated the effects of 10% (w/v) salt, trisodium phosphate (TSP), sodium tripolyphosphate (STPP), and tetrapotassium pyrophosphate (TKPP) washes on removal of attached Salmonella typhimurium from sterile chicken breast patties, as well as on their injury and survival in a refrigerator for 16 d, in a –20 °C freezer for 10 mo, and after 3 freeze-thaw cycles. S. typhimurium were grown on chicken patties at 20 °C for 20 h, washed, and enumerated by plating on selective and nonselective media. Salt and phosphates washing significantly lowered the survival populations of attached S. typhimurium on patties, but did not cause any significant sublethal injury of attached S. typhimurium , irrespective of storage treatments. The TSP washes showed superior effects of removing and inactivating S. typhimurium compared to other washing treatments.     

The onset of vortex instability in laminar forced convection flow through a horizontal porous channel

The onset of convective instability in a fluid-saturated porous layer between the two horizontal plates heated isothermally from below has been analyzed theoretically by using propagation theory. In the analysis the thermal dispersion coefficient is assumed to be proportional to the streamwise velocity. The results show that both inertia and thermal dispersion stabilize the system.     

Synthesis and characterization of an interpenetrating polymer network composed of poly(methacrylic acid) and poly(vinyl alcohol)

Temperature and pH‐responsive interpenetrating polymer network (IPN) hydrogels, constructed with poly(methacrylic acid) (PMAA) and poly(vinyl alcohol) (PVA), by a sequential IPN method, were studied. The characterization of IPN hydrogels was investigated by Fourier‐transform infrared spectroscopy, differential scanning calorimetry (DSC) and swelling under various conditions. The IPN hydrogels exhibited relatively high swelling ratios, in the range 230–380 %, at 25 °C. The swelling ratios of the PMAA/PVA IPN hydrogels were pH and temperature dependent. DSC was used for the quantitative determination of the amounts of freezing and non‐freezing water. The amount of free water increased with increasing PMAA content in the IPN hydrogels. Copyright © 2004 Society of Chemical Industry     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Dielectric reliability of stacked Al2O3–HfO2 MIS capacitors with cylinder type for improving DRAM data retention characteristics

Dielectric reliability in Al₂O₃(2–3.1nm)–HfO₂(3nm) stack capacitor with Metal–Insulator–Si(MIS) structure is investigated in this paper. We propose an optimized capacitor process through the Time–Dependent Dielectric Breakdown (TDDB) data under various process conditions. Furthermore, due to asymmetric current at both negative and positive voltage stress polarities, we show different lifetime extrapolation by a fluence–driven model. As a result, the maximum allowed operating voltage is projected to be 1.7V (failure rate 10ppm during 10year @ 85°C) for Data “0” retention lifetime.     

Crosslinking reactions and swelling behavior of matrices based on N-acryloyl-TRIS(hydroxymethyl)aminomethane

Summary In this study, new hydrogels in rod shape were prepared from N-acryloyl-TRIS(hydroxymethyl)aminomethane (NAT) using ethylene glycol dimethacrylate (EGDMA) or N,N’methylenebisacrylamide (BIS) as crosslinking agent, dimethylformamide (DMF) as solvent and benzoyl peroxide (BPO) as initiator. In most cases, 2-hydroxyethyl methacrylate (HEMA), acrylamide (Aam) or acrylic acid (Aac) were used as co-monomers. The polymeric matrices obtained by free radical polymerization exhibited different properties by changing crosslinker, crosslinker concentration, co-monomer and initial NAT/co-monomer mole ratio. Besides, hydrogels from HEMA, Aam and Aac with BIS in absence of NAT were prepared under the same experimental reaction conditions in order to compare the properties of these products with those synthesized from NAT and the respective co-monomers. Some of the final products were selected to perform urea release assays, conducted through swelling-controlled release. Urea was chosen as “model” plant fertilizer agent.     

Production and structural features of a water-soluble polysaccharide from a mutant strain of Agrobacterium sp.

We have developed a mutant strain derived from Agrobacterium sp. ATCC 31750, which produces a water-soluble polysaccharide having potential utility to the food, feed, pharmaceutical and cosmetic industries. A high concentration of product (15 g/L) is obtained by 48 h cultivation of the mutant strain under optimized fermentation conditions. The water-soluble polysaccharide obtained from cultures of the mutant strain beta82 has Glc:Man:Gal in approximate molar ratios of 5.8:6.7:1.0. The molecular weight of the polysaccharide was determined to be approximately 1000 kDa by HPSEC analysis. Linkage analysis contained 3-Glcp, 3-Manp, terminal Glcp and terminal Manp, as well as a small proportion of 3- and 3,4-Galp, and 4,6-Manp residues. Based on analyses using FT-IR and ¹³C NMR spectrometers, most glycosidic bonds joining these sugar residues are of the α-type, and acetyl groups are apparently attached to the polymer chain at random.     

Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.