首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

Symmetrized Split-Step Fourier Scheme to Control Global Simulation Accuracy in Fiber-Optic Communication Systems

Analytical expressions involving both system parameters and step-size are proposed to represent the local simulation error for the symmetrized split-step Fourier (SSSF) simulation method. This analytical expression can be used for a step-size selection rule to achieve comparable local simulation accuracy for SSSF simulations. This can lead to computational savings since there is no waste of computation in each simulation step. Furthermore, based on the local error expression, scaling rules are derived to achieve comparable global simulation accuracy for wide ranges of key system parameter values. This is significant in enhancing the computational efficiency in optical fiber communication system design and optimization. Extensive validation tests were performed to explore the application range of the proposed step-size selection and scaling rules. The desired global accuracy can be achieved with the use of our local error expression and scaling rules by only a couple of test trial simulation runs for a variety of practical applications.     

黄磷渣制备多孔陶瓷的研究

研究了用黄磷渣代替部分粘土作陶瓷原料，既可以解决磷渣对环境的污染和堆放占用耕地问题，使该固体废弃物资源化，又能缓解陶瓷原料的短缺。     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

A Recursive Frequency Estimator Using Linear Prediction and a Kalman-Filter-Based Iterative Algorithm

This paper proposes a new Kalman-filter-based recursive frequency estimator for discrete-time multicomponent sinusoidal signals whose frequencies may be time-varying. The frequency estimator is based on the linear prediction approach and it employs the Kalman filter to track the linear prediction coefficients (LPCs) recursively. Frequencies of the sinusoids can then be computed using the estimated LPCs. Due to the coloredness of the linear prediction error, an iterative algorithm is employed to estimate the covariance matrix of the prediction error and the LPCs alternately in the Kalman filter in order to improve the tracking performance. Simulation results show that the proposed Kalman-filter-based iterative frequency estimator can achieve better tracking results than the conventional recursive least-squares-based estimators.     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

以奥林匹克精神为纲——中国运动鞋品牌运行之我见

2008年29届奥运会在北京举行，使得有关奥运的话题成为热门中的热门，与运动有关或无关的众多品牌、厂商对北京奥运年均寄予厚望，为赢取更大的收获和提升品牌知名度作最大的努力。其实早在几年前，国内外运动鞋品牌企业就已经大张旗鼓，在产品研发与广告宣传等多方面投入重金，为在这次北京奥运年带来的难得契机中处于市场制高点或明或隐地博杀着。     

Asset-Management of Transformers Based on Condition Monitoring and Standard Diagnosis [Feature Article]

In this paper, a methodology is developed to use data acquisition derived from condition monitoring and standard diagnosis for rehabilitation purposes of transformers. The interpretation and understanding of the test data are obtained from international test standards to determine the current condition of transformers. In an attempt to ascertain monitoring priorities, the effective test methods are selected for transformer diagnosis. In particular, the standardization of diagnostic and analytical techniques are being improved that will enable field personnel to more easily use the test results and will reduce the need for interpretation by experts. In addition, the advanced method has the potential to reduce the time greatly and increase the accuracy of diagnostics. The important aim of the standardization is to develop the multiple diagnostic models that combine results from the different tests and give an overall assessment of reliability and maintenance for transformers.