Antibacterial activity of peptides extracted from tryptic hydrolyzate of whey protein by nanofiltration

Ultrafiltration permeate of whey protein tryptic hydrolyzate was processed by nanofiltration (NF) to obtain retentate (NFR) and permeate (NFP) that were then tested as inhibitors of Listeria, Staphylococcus aureus and Escherichia coli. NFR at 20 mg mL^?1 was most effective as an inhibitor (P < 0.001); whereas E. coli was relatively resistant, the effect on Listeria and S. aureus was greater at 20 mg mL^?1 than at 10 mg mL^?1 (P < 0.01). Peptide analysis revealed that NFR was rich in anionic peptides over eight amino acid residues in length. The antibacterial activity of two anionic peptides (84–91 and 125–135) and a cationic peptide (36–42) derived from β-lactoglobulin was tested. Peptide 125–135 was more inhibitory (P < 0.05) than peptide 84–91 against Listeria monocytogenes and S. aureus; peptide 36–42 was not inhibitory. NFR appears to have potential as a natural bio-preservative.     

Numerical modelling of geothermal vertical heat exchangers for the short time analysis using the state model size reduction technique

According to the introduction of a dynamic operating mode in ground-coupled heat pump systems, a short time analysis within and around borehole heat exchangers is required in the modern geothermal system simulation. A numerical modelling could be a proper answer for this challenge. However, the numerical model is time consuming and necessitates a large memory particularly in such large systems. Therefore, the state model size reduction technique has been applied in this paper with various numerical techniques particularly in the finite elements method. As a result, the reduced model developed is: (a) relevant with a validation using a traditional analytical model (using 100% modes) and (b) efficient in calculation time, only using 6% modes and consequently reducing time consumption up to 95%.     

Fusing Loop Detector and Probe Vehicle Data to Estimate Travel Time Statistics on Signalized Urban Networks

Abstract: This article presents a methodology that integrates cumulative plots with probe vehicle data for estimation of travel time statistics (average, quartile) on urban networks. The integration reduces relative deviation among the cumulative plots so that the classical analytical procedure of defining the area between the plots as the total travel time can be applied. For quartile estimation, a slicing technique is proposed. The methodology is validated with real data from Lucerne, Switzerland and it is concluded that the travel time estimates from the proposed methodology are statistically equivalent to the observed values.     

Toward a Trust‐Based Construction Management

Abstract: The growing complexity of AEC projects is increasing the importance of the building construction coordination role. Moreover, the uncertainty linked to the environment of the construction activity makes way for the notion of trust. The coordinator can make use of multiple tools/views for accomplishing his mission. This research work suggests analyzing data coming from these different views to consolidate trust indicators informing the coordinator about “trust in the correct progression of the construction activity.” The approach suggested in this article distinguishes between four aspects of the activity determining the global trust level: task progress, actor's performance, documents required to perform the task, and building elements resulting from the task. The proposal suggests introducing these trust indicators in a dashboard, included in a multiview interface, thus allowing the coordinator to identify the tasks with a low trust level and to understand the nature of dysfunctions. A prototype has been developed and integrated in a service‐based IT infrastructure. Results of an experiment stage are finally discussed to validate the approach.     

Anisothermal thermosetting resin cure monitored by optical fiber refractometer

The cure monitoring of composite parts is an important key to optimize the industrial curing cycles. In this study, it is proposed to monitor the cure of a thermosetting resin by a Fresnel refractometer. The measurements are first compared to dielectric analyses and predictions of a thermo‐kinetic model that uses parameters from the literature. Under isothermal conditions, the results show that the Fresnel power can be directly exploited to obtain qualitatively the degree of conversion. This is also demonstrated in anisothermal conditions by correcting the Fresnel signal from its temperature dependence. If the initial degree of conversion is known, its quantitative assessment is achieved using the Fresnel and temperature measurements. POLYM. ENG. SCI., 54:626–635, 2014. © 2013 Society of Plastics Engineers     

Kinetics of heavy metal vaporization from model wastes in a fluidized bed

Metal vaporization experiments were carried out in an atmospheric fluidized bed to study the influence of operating conditions on the extent of heavy metal (HM) release in fumes from municipal solid waste incinerators. Modelwastes spiked with compounds of Pb, Cd, and Zn were used. The parameters studied were temperature, treatment duration, matrix of the model waste (mineral and organic), HM initial speciation, and gas composition (N2, air, air + HCl, gas mixture simulating the incinerators). The extent of vaporization was measured by solid sample analysis and on-line analysis of the gaseous effluent, after customization of the ICP technique for gas analysis. The results indicate the metal vaporization rate is very high initially and then slows. The results with mineral matrices give the decreasing order of volatility Cd > Pb > Zn, but in industrial incinerators Zn volatilizes slightly more than Pb. Temperature (especially for porous alumina) and mineral matrix have a strong influence on the HM vaporization, but HCl concentration and HM initial speciation do not. The gas composition and the initial metal concentration are significant parameters. The matrix influence clearly denoted the mass transfer limitations in the vaporization process from mineral matrix.     

Iron (III) aquacomplexes as effective photocatalysts for the degradation of pesticides in homogeneous aqueous solutions

This study evaluated in-car and in-bus exposures to methyl-tertiary butyl ether (MTBE), benzene, and toluene on actual commuting routes, not hypothetical routes as used in many previous in-vehicle exposure studies of volatile organic compounds (VOCs). It focuses on four potentially influencing factors (transportation mode, passenger-car type, time of day, and season). A total of 40 passenger car commuters and 20 public bus commuters were recruited. The same commuters participated in both the summer and winter studies. The transportation mode, passenger-car type and commute season were all found to affect the in-vehicle levels of the target VOCs. Conversely, the commute time of day had little effect on the in-car and in-bus levels of the target compounds. The present study also confirmed that under Korean commuting conditions, passenger car and public bus interiors are important microenvironments for exposure to MTBE, benzene and toluene. This is supported by a previous finding that both in-car and in-bus air levels of the target VOCs tend to be much higher than ambient air levels of the compounds. Meanwhile, some spurious gasoline sold during the experimental periods appears to have elevated the in-car and in-bus exposures to toluene compared with those reported by some previous studies conducted in the same study area.     

A system for automatic measurement of circadian activity deviations in telemedicine

A system for the automatic measurement of the circadian activity deviations in telemedicine has been developed within the framework of a "Health Integrated Smart Home Information System" (HIS2). HIS2 is an experimental platform for the evaluation and the development of technologies in order to ensure the security and quality of life for patients who need home based medical monitoring. Location sensors are placed in each room of the HIS2, allowing the monitoring of patient's successive activity phases within the patient's home environment. We proceeded with a sampling in an hourly schedule to detect weak rhythmic variations. Based on numerous measurements, we established a mean value with confidence limits. These also allowed us to define a zone within which the patient's activity is qualified to be "predictable." Alerts are set off if the patient's activity deviates from this zone.     

Multigrid preconditioned conjugate-gradient method for large-scale wave-front reconstruction

We introduce a multigrid preconditioned conjugate-gradient (MGCG) iterative scheme for computing open-loop wave-front reconstructors for extreme adaptive optics systems. We present numerical simulations for a 17-m class telescope with n = 48756 sensor measurement grid points within the aperture, which indicate that our MGCG method has a rapid convergence rate for a wide range of subaperture average slope measurement signal-to-noise ratios. The total computational cost is of order n log n. Hence our scheme provides for fast wave-front simulation and control in large-scale adaptive optics systems.     

AM noise impact on low level phase noise measurements

The influence of the source AM noise in microwave residual phase noise experiments is investigated. The noise floor degradation problem, caused by the parasitic detection of this type of noise by an imperfectly balanced mixer, is solved thanks to a refinement of the quadrature condition. The parasitic noise contribution attributable to the AM to PM (phase modulation) conversion occurring in the device under test is minimized through the development of a dedicated microwave source featuring an AM noise level as low as -170 dBc/Hz at 10 kHz offset from a 3.5 GHz carrier