A conformal cylindrical microstrip array for producing omnidirectional radiation pattern

Radiation patterns of rectangular microstrip patches arranged circumferentially on a circular cylinder have been computed. Both the axial patches and circumferential patches have been used. It has been found that the number of circumferential patches required for a given ripple in gain pattern is considerably less, thus simplifying the feed network. Comparison with experimental measurements shows good agreement.     

Distribution of trivalent rare-earth additives between A and B sites in the ABO3 PZT system

Lead zirconate titanate ceramics having composition at the morphotropic phase boundary have been modified with 2 mol % rare-earth oxides of Er, Gd, Eu, Nd and La. The samples have been prepared using the standard solid state reaction route. The ionic radius of the additives investigated vary from 0.088 to 0.106 nm. A theoretical model has been used which allows the additive cation distribution between A and B sites to be established from its ionic radius. It has been concluded that the additive goes increasingly to the A site with increasing ionic radius. The amounts of lead monoxide liberated during sintering due to incorporation of the additives have been studied. Using this PbO loss data the distribution of the additive between A and B sites has been calculated. It has been observed that the experimental results agree well with theoretical calculations.     

A biomechanical and ergonomic evaluation of patient transferring tasks: wheelchair to shower chair and shower chair to wheelchair.

A laboratory study was conducted to evaluate five different manual techniques (two-person manual lifting; rocking and pulling the patient using a gait belt with two persons; walking belt with one and two persons) and three different mechanical hoists (Hoyer lift, Trans-Aid and Ambulift) for transferring patients from wheelchair to shower chair and shower chair to wheelchair. Six female nursing students with prior patient transfer experience served both as nurses and as passive patients. Static biomechanical evaluation showed that the mean trunk flexion moments, erector spinae muscle forces and compressive and shear forces at the L5S1 disc for the four pulling methods ranged from 92 to 125 Nm, 1845 to 2507 N, 1973 to 2641 N and 442 to 580 N, respectively, as compared to about 213 Nm, 4260 N, 5050 N and 926 N for two-person manual lifting. Perceived stress ratings for the shoulder, upper back, lower back and whole body were significantly lower for pulling methods than those for lifting the patient (p less than or equal to 0.01). Patients found pulling techniques, except the gait belt, to be more comfortable and secure than the lifting method (p less than or equal to 0.01). However, most of the nurses believed that Medesign and the one-person walking belt would not work on those patients who cannot bear weight and those who are heavy, contracted or combative. A two-person walking belt was the most preferred method. Two out of three hoists (Hoyer lift and Trans-Aid) were perceived by the nurses to be more stressful than one- and two-person walking belts. The patients found these two hoists to be more uncomfortable and less secure than with three of the five manual methods (one- and two-person walking belts and Medesign). Pulling techniques and hoists took significantly longer amounts of time to make the transfer than manually lifting the patient (p less than or equal to 0.01). The two-person walking belt, using a gentle rocking motion to utilize momentum and a pulling technique, and Ambulift are recommended for transferring patients from wheelchair to shower chair and shower chair to wheelchair.     

Parametric Study of Jatropha Seeds for Biodiesel Production by Reactive Extraction

The purpose of the present study was to reduce the cost and increase the efficiency of biodiesel production by reactive extraction (in situ) of Jatropha seeds. Oil from the seeds was extracted and reacted in a single step. Experimental studies have been carried out to maximize the yield of biodiesel by varying the reaction parameters viz. seed size (<0.85 mm to >2.46 mm), seed/solvent ratio (w/w) (1:2.6–1:7.8) and catalyst concentration (0.05–0.1 M). Under the optimized conditions: seed size (>2.46 mm), seed/solvent ratio (w/w) (1:7.8), catalyst concentration (0.1 M) and reaction time 1 h, approximately 98% conversion to biodiesel was achieved meeting International (ASTM) as well as National (BIS) specifications. The results were supported by HPLC analysis.     

A fully coupled quadrature-based moment method for dilute to moderately dilute fluid–particle flows

A third-order quadrature-based moment method for simulating dilute and moderately dilute fluid–particle flows has been implemented with full coupling in a computational fluid dynamics code. The solution algorithm for the particle phase uses a kinetic-based finite-volume technique to solve the velocity moment equations derived from kinetic theory. The procedure to couple the particle-phase volume-fraction and momentum equations with the Eulerian solver for the fluid phase is explained in detail. As an example application, simulations of a particle-laden vertical channel flow at fluid-phase Reynolds number 1379 and particle Stokes numbers 0.061 and 0.61 were carried out. The fluid and particle velocities, particle-phase volume fraction and granular temperature were observed to reach a steady state in the case of Stokes number 0.061, while instabilities that led to the formation of structures and initiated the particle segregation process were observed in the case with the higher Stokes number. These results are validated against results from a classical two-fluid model derived from the kinetic theory of granular flows in the small Knudsen number limit, and Euler–Lagrange simulations of the same flow.     

Synthesis and electrochemical characterizations of nano-scaled Zn doped LiMn2O4 cathode materials for rechargeable lithium batteries

The LiZn_xMn_2−xO₄ (x = 0.00-0.15) cathode materials for rechargeable lithium-ion batteries were synthesized by simple sol-gel technique using aqueous solutions of metal nitrates and succinic acid as the chelating agent. The gel precursors of metal succinates were dried in vacuum oven for 10 h at 120 °C. After drying, the gel precursors were ground and heated at 900 °C. The structural characterization was carried out by X-ray powder diffraction and X-ray photoelectron spectroscopy to identify the valance state of Mn in the synthesized materials. The sample exhibited a well-defined spinel structure and the lattice parameter was linearly increased with increasing the Zn contents in LiZn_xMn_2−xO₄. Surface morphology and particle size of the synthesized materials were determined by scanning electron microscopy and transmission electron microscopy, respectively. Electrochemical properties were characterized for the assembled Li/LiZn_xMn_2−xO₄ coin type cells using galvanostatic charge/discharge studies at 0.5 C rate and cyclic voltammetry technique in the potential range between 2.75 and 4.5 V at a scan rate of 0.1 mV s⁻¹. Among them Zn doped spinel LiZn_0.10Mn_1.90O₄ has improved the structural stability, high reversible capacity and excellent electrochemical performance of rechargeable lithium batteries.     

Calculation of Channel Capacity Considering the Effect of Different Seasons for Higher Altitude Platform System

This paper presents effect of the weather impairments on a high altitude platform (HAP) broadband wireless communication system. It is shown that attenuation due to oxygen, water vapor, fog, cloud, and rain has significant effect on a radio link which is operating in a millimeter frequency range. Channel capacity is calculated for different seasons using Shannon’s channel capacity theorem. The location of HAP is taken to be Delhi (India). Further, it is considered that a user and the HAP platform are stationary.     

Mathematical modelling of burr height of the drilling process using a statistical-based multi-gene genetic programming approach

Drilling is one of the important machining processes performed extensively in production industry. Literature emphasises that the output process parameters such as burr height, surface roughness, strength, etc. are related to and can be improved by the appropriate settings of the input process parameters. Recently, researchers have applied well-known computational intelligence methods such as regression analysis, artificial neural networks (ANNs), support vector regression (SVR), etc. in the prediction of performance characteristics of the drilling process. Alternatively, an evolutionary approach of multi-gene genetic programming (MGGP) that evolves the model structure and its coefficients automatically can be applied. Despite of being widely applied, MGGP has the limitation for producing models that over-fit on the testing data. One of the reasons attributed for this behaviour is the over-size of the evolved models. Therefore, a statistical-based MGGP (S-MGGP) approach is proposed and applied to the burr height data obtained from the drilling of AISI 316L stainless steel. In this proposed approach, Bayesian information criterion is embedded in its paradigm, which punishes the fitness of larger size models. The performance of S-MGGP and ANN models is found to be better than those of the standardised MGGP and SVR. Further, the parametric and sensitivity analysis conducted validates the robustness of our proposed model and is proved to capture the dynamics of the drilling phenomenon by unveiling dominant input process parameters and the hidden non-linear relationships.     

Weight loss and metabolic profiles in obese individuals using two different approaches

Intentional weight loss with a reduction in adipose tissue is associated with an improvement in medical complications linked to obesity. The aim of this study was to compare the effect of two different weight loss diets on obese individuals (BMI 30-40 kg m(-2)) for improvements in anthropometric measurements and blood biomarkers. Study 1 comprised a low energy diet (LED) of 5000-6000 kJ d(-1) for a slow but steady weight loss over 12 weeks. Study 2 comprised a very low energy diet (VLED) of 3000 kJ d(-1) using meal replacements for rapid weight loss over a shorter period of 4 weeks followed by 10 weeks of weight stabilisation to prevent rebound after rapid weight loss. Nutrition information sessions were given to both groups. Fasting blood samples, anthropometric measurements and 3-day food diaries were collected at baseline and again at completion of weight loss, at 12 weeks for LED group and 4 weeks for VLED group. Mean weight loss in the LED group (n = 18) was -3.17 kg (-3.7%) compared to a -6.54 kg (-7%) loss in the VLED group (n = 14) (p < 0.001). The VLED group experienced significantly greater reductions in fat mass, -13.9% compared to -8.9% for the LED group (p < 0.05). Significantly greater reductions in blood glucose (p < 0.05), cholesterol and LDL-C (p < 0.01 for both), and waist circumference (p≤ 0.05) were noted in VLED compared to those for LED diet. Short-term, rapid weight loss produced the desired ≥5% weight loss suggested to substantially reduce metabolic abnormalities associated with obesity, and to reduce health risks.     

Combined synchronization and power control for differentially-encoded di-symbol time-division multiuser impulse radio

The differentially-encoded, di-symbol time-division multiuser impulse radio (d²TD-IR) with delay-sum autocorrelation receivers is a low complexity, high efficiency short range wireless communication technology for infrastructure networks. The d²TD-IR system is designed with the assumption that the users are perfectly synchronized. In this letter, we propose a recursive algorithm of combined synchronization and power control. Computer simulation results show that the proposed algorithm has significant performance improvement over the algorithm, in which synchronization and power control are performed separately.