Concomitant Crystallization of Copper(II) Sachharinato Complexes with 2-methylpyrazine as a Monomer and an One-dimensional Polymer: Syntheses,Crystal Structures,Spectroscopic and Thermal Properties

The reaction of [Cu(sac)₂(H₂O)₄] · 2H₂O with 2-methylpyrazine (mpyz) leads two complexes, concomitant crystallization of a mononuclear complex [Cu(sac)₂(mpyz)(H₂O)₂] (1) and a polymeric complex [Cu(sac)₂(μ-mpyz)]_n (2). Both complexes have been characterized by elemental analyses, magnetic measurements, FT-IR and ESR, TG-DTA and single-crystal X-ray diffraction analyses. Single-crystal X-ray analyses show that complex 1 consists of discrete molecules in which the copper(II) ions exhibits a square-pyramidal coordination geometry. The individual molecules of 1 are connected into a hydrogen-bonded chain structure, which is further assembled to form a three-dimensional network by π–π stacking interactions. Complex 2 is an 1D coordination polymer in which copper(II) centers are bridged by the mpyz ligand. The chains are further assembled to form two-dimensional frameworks by π–π and C–H···π stacking interactions.     

Corrosion inhibition of steel in concrete by carboxylic acids

Water soluble carboxylic acids have been used as corrosion inhibitors. They remain largely soluble after curing in cement for up to 90d. Corrosion current measurements are presented showing malonic acid, a dicarboxylic acid, to be a very effective corrosion inhibitor even in the presence of 2.5 wt % chloride. Unfortunately, it has an initial retarding effect on the set of Portland cement. The investigation suggests that corrosion inhibitors based on carboxylic acids remain a fruitful field of investigation.     

Unusual swelling behavior of polymer-clay nanocomposite hydrogels

The swelling behavior and the elastic properties of nanocomposite hydrogels have been investigated. The hydrogels were prepared by free-radical polymerization of the monomers acrylamide (AAm), N,N-dimethylacrylamide (DMA), and N-isopropylacrylamide (NIPA) in aqueous clay suspensions at 21 °C. Laponite with a radius of gyration in distilled water of 20 nm was used as clay particles in the hydrogel preparation. The reactions with AAm monomer were carried out in the presence of the chemical crosslinker N,N′-methylenebis(acrylamide) (BAAm). It was found that the volume of nanocomposite hydrogels immersed in water rapidly increases and attains a maximum value after about one day. Surprisingly, further increase in the swelling time results in the deswelling of the gels until they reach a limiting swelling ratio after about 5 days. This unusual swelling behavior is observable only when the clay concentration in the hydrogel is above the overlap threshold c^∗. Swelling measurements combined with the elasticity tests show that the effective crosslink density first decreases, but then increases with increasing time of swelling of the hydrogels. The results were explained in terms of the rearrangements of the highly entangled polymer chains and clay particles during the gel volume change.     

Poly(Li‐2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine): Molar mass effects on strong electrorheological response

Electrorheological (ER) fluids display remarkable rheological behavior, being able to convert rapidly and repeatedly from a fluid to a solid‐like when an external electric field (E) is applied or removed. In this study, electrical and ER properties of poly(Li‐2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine), poly(Li‐HEMA)‐co‐poly(4‐VP), copolymeric salts (ionomers) were investigated. For this purpose six ionomers were synthesized with different molar masses. They were then ground‐milled for a few hours to obtain micron size ionomers. The particle sizes of the ionomers were determined by dynamic light scattering. Suspensions of ionomers were prepared in silicone oil (SO), at a series of concentrations (c = 5–30%, m/m). The gravitational stability of suspensions against sedimentation was determined at constant temperature (T = 25°C). Flow times of the suspensions were measured under no electric field (E = 0 kV/mm), and under an external applied electric field (E ≠ 0 kV/mm) strengths and a strong ER activities were observed for all the poly(Li‐HEMA)‐co‐poly(4‐VP)/SO suspensions. Further, the effects of suspension concentration, mole ratios of poly(HEMA) and poly(4‐VP), and the overall molar mass of the copolymers, shear rate, electric field strength, frequency, promoter, and temperature onto ER activities of ionomer suspensions were investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1065–1074, 2006     

Fabrication of co-PVDF/modacrylic/SiO2 nanofibrous membrane: Composite separator for safe and high performance lithium-ion batteries

Highly porous free-standing co-poly(vinylidene fluoride)/modacrylic/SiO₂ nanofibrous membrane was developed using electrically-assisted solution blow spinning method. The performance and the potential of the membrane as a lithium-ion battery separator were investigated. The addition of modacrylic enhanced the solution spinnability that resulted in defect-free membranes. Moreover, the presence of modacrylic enhanced the dimensional and thermal stabilities, while the addition of hydrophilic SiO₂ nanoparticle enhanced both mechanical property and ionic conductivity. Combustion test results illustrated that the presence of modacrylic provide flame retarding property over a set of different polymeric-based membranes. Electrochemical performance results showed that the developed membrane can increase the battery capacity compared with the commercial separator.     

Graphene oxide-containing isocyanate-based polyimide foams: Enhanced thermal stability and flame retardancy

Isocyanate-based graphene oxide-containing polyimide foams were synthesized by a semi-prepolymer method. In this method, while the first solution containing pre-polymer was derived from pyromellitic dianhydride and excess polymethylene polyphenylene isocyanate (PM200), the second solution contains dianhydride derivatives, water, catalysts, surfactants, and graphene oxide. PIFs were prepared with 0%, 0.25%, 0.50%, 0.75%, and 1% graphene oxide by weight, respectively. PIFs exhibited a minimum side reaction and urea generation was not seen for all PIFs instead of imide bonding. The addition of graphene oxide (GO) leads to a more close-packed structure. Therefore, crosslinking density and thermal stability of graphene oxide-containing polyimide foams increased. Upon the addition of 1% GO, almost seven times higher compression strength was obtained compared to neat PIFs. Also, LOI values supported the theory that thermally stable and flame retardant PIFs can be synthesized via the isocyanate-based process with GO.     

Exploring the Belief Systems of Software Development Professionals

It is commonly accepted that an individual's beliefs and actions are based on his or her assessment and perceptions of the world. In order to determine what practices an individual is likely to follow at any given time, it is necessary to understand the individual's behavioral intention in a given circumstance. From an Information Technology perspective, a software development professional's belief systems are potentially the basis for the adoption and implementation of new and innovative work practices and processes. In this article, we explore the belief systems of software development professionals in order to understand the beliefs underlying intention and practice, and we seek answers about how they adopt or reject new and innovative software development processes and practices. The results point out a strong influence of past experiences, personality types, and repeated behavior on current software development processes and practices in industrial settings.     

Vegetation water content during SMEX04 from ground data and Landsat 5 Thematic Mapper imagery

Vegetation water content is an important parameter for retrieval of soil moisture from microwave data and for other remote sensing applications. Because liquid water absorbs in the shortwave infrared, the normalized difference infrared index (NDII), calculated from Landsat 5 Thematic Mapper band 4 (0.76-0.90 μm wavelength) and band 5 (1.55-1.65 μm wavelength), can be used to determine canopy equivalent water thickness (EWT), which is defined as the water volume per leaf area times the leaf area index (LAI). Alternatively, average canopy EWT can be determined using a landcover classification, because different vegetation types have different average LAI at the peak of the growing season. The primary contribution of this study for the Soil Moisture Experiment 2004 was to sample vegetation for the Arizona and Sonora study areas. Vegetation was sampled to achieve a range of canopy EWT; LAI was measured using a plant canopy analyzer and digital hemispherical (fisheye) photographs. NDII was linearly related to measured canopy EWT with an R² of 0.601. Landcover of the Arizona, USA, and Sonora, Mexico, study areas were classified with an overall accuracy of 70% using a rule-based decision tree using three dates of Landsat 5 Thematic Mapper imagery and digital elevation data. There was a large range of NDII per landcover class at the peak of the growing season, indicating that canopy EWT should be estimated directly using NDII or other shortwave-infrared vegetation indices. However, landcover classifications will still be necessary to obtain total vegetation water content from canopy EWT and other data, because considerable liquid water is contained in the non-foliar components of vegetation.     

Effect of CR and FT-paraffin versus SBS modification in terms of conventional and rheological properties

In this study, the rheological and conventional properties of binders prepared with crumb rubber (CR) and FT-paraffin were compared to styrene-butadiene-styrene (SBS)-modified binders’ properties. The objective of this study was to determine which modified binders in different combinations of the CR and the FT-paraffin exhibited better performance than the SBS-modified binders, in terms of conventional and rheological properties. Results showed that the additives exhibited different performances for different types of tests. Many of the combinations including the common usage of the CR and the FT-paraffin performed better at high temperature than the SBS modification. Overall, the test results show that the binders prepared by 6% CR with 3 and 4% FT-paraffin and those prepared with 8% CR with 3% FT-paraffin were better binders than the 4% SBS-modified binder, in terms of low and high temperature properties.