Three Basic Theorems in Numerical Analysis in Control Engineering Course and Their Application

International Journal of Control, Automation and Systems - Control system design packages like MATLAB, SICLAB, OCTAVE, etc. have become essential components of both undergraduate and graduate...     

An estimation of friction from the indentation of metals by acute-angled conical indenters

The paper describes a method for estimating the coefficient of friction (COF) between sliding surfaces by an indentation of an acute-angled indenter. The COF estimated by the method is compared with the COF measured by a friction tester. The conical indenter, which is made of WC and has an apex angle of 45°, is used for the experiments. A micro-Vickers hardness tester is used for the indentation tests. The friction tester used is one of Bowden–Leben type. A copper and a 0.45% carbon steel are used for the indentation and sliding specimens. The estimation of the COF is based on the equilibrium equation of indentation, which takes the friction between the contacting surfaces of the indenter and the specimen into consideration. The results show that the estimated COF is approximately equal to the measured one. Based on the results, the validity of this method is discussed.     

Processing and properties of an ethylene–vinyl acetate blend foam incorporating ethylene–vinyl acetate and polyurethane waste foams

Waste polyurethane foam (w‐PU) and waste ethylene–vinyl acetate foam (w‐EVA) were used as fillers for the production of an ethylene–vinyl acetate (EVA) blend foam. Two different foaming techniques (single‐stage and heat–chill processes) were used for this purpose. The waste foam concentration was varied up to 30 wt % of the original EVA. The physical, mechanical, and morphological properties of the filled foam were studied. The single‐stage process produced blend foams with a lower density and a greater cell size than the foams obtained by the heat–chill process. The density and compression strength of the blend foam increased as the percentage of w‐PU foam increased. However, for the w‐EVA/EVA blend foams, the addition of w‐EVA foam did not significantly affect the density or compression strength compared to the original EVA foams. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44708.     

Evidence for enhanced thermal conduction through percolating structures in nanofluids

The unusually large enhancement of thermal conductivity (k/k(f)～4.0, where k and k(f) are the thermal conductivities of the nanofluid and the base fluid, respectively) observed in a nanofluid containing linear chain-like aggregates provides direct evidence for efficient transport of heat through percolating paths. The nanofluid used was a stable colloidal suspension of magnetite (Fe(3)O(4)) nanoparticles of average diameter 6.7?nm, coated with oleic acid and dispersed in kerosene. The maximum enhancement under magnetic field was about 48φ (where φ is the volume fraction). The maximum enhancement is observed when chain-like aggregates are uniformly dispersed without clumping. These results also suggest that nanofluids containing well-dispersed nanoparticles (without aggregates) do not exhibit significant enhancement of thermal conductivity. Our findings offer promising applications for developing a new generation of nanofluids with tunable thermal conductivity.     

Development of incremental deep drawing process

This paper deals with development of an incremental deep drawing process. On a newly developed incremental deep drawing set-up, the aluminium sheets are formed; the forming is carried out by deep-drawing the blank as in the conventional method but incrementally. Fractures at the punch or die corner in the blank may or may not occur depending on the conditions; the process parameters involved are punch size, punch corner radius, increment in punch displacement, blank holding force or pressure, etc. It is thus shown that different shapes are formed by one set of common tools. It is thereby confirmed that incremental deep drawing is possible without using a particular tool set for a particular shape.     

A Study of Polymer Electrolyte Fuel Cells by the Measurement of AC Impedance,Current Interrupt,and Dew Points: 2. Effect of Cell Temperature

The effect of cell temperature on the performance of a polymer electrolyte fuel cell was examined in the present study. Measurements using the current interrupt and AC impedance methods showed that membrane resistance increased as the cell temperature was reduced. The charge transfer resistance, determined by the AC impedance method, also increased with decreasing cell temperature. The results of electrochemical analysis showed that the temperature of the cell strongly affected the performance of the membrane–electrode assembly in the cell. In addition, the water balance calculated from dew points of fuel gases changed with cell temperature. At a cell temperature of 80 °C, ca. 80% of the water generated on the cathode passed through the membrane to the anode, while at a cell temperature of 40 °C, only ca. 20% of the water on the cathode passed through the membrane to the anode.     

Another approach to asymptotic model matching problem for nonlinear systems

This paper deals with the asymptotic model matching problem for square nonlinear systems. This problem has been studied by Di Benedetto and Grizzle via geometric approach. We adopt another approach. It is based on an idea that this problem is similar to the nonlinear servomechanism (output regulation) problem. By means of slight modification of the problem statement, a sufficient condition is given. It is described as the solvability of a certain partial differential equation. Its reduction and approximation methods are proposed. © 1998 John Wiley & Sons, Ltd.     

Airborne endotoxin concentrations in indoor and outdoor particulate matter and their predictors in an urban city

Endotoxins are an important biological component of particulate matter and have been associated with adverse effects on human health. There have been some recent studies on airborne endotoxin concentrations. We collected fine (PM_2.5) and coarse (PM_10‐2.5) particulate matter twice on weekdays and weekends each for 48 hour, inside and outside 55 homes in an urban city in Japan. Endotoxin concentrations in both fractions were measured using the kinetic Limulus Amebocyte Lysate assay. The relationships between endotoxin concentrations and household characteristics were evaluated for each fraction. Both indoor and outdoor endotoxin concentrations were higher in PM_2.5 than in PM_10‐2.5. In both PM_2.5 and PM_10‐2.5, indoor endotoxin concentrations were higher than outdoor concentrations, and the indoor endotoxin concentrations significantly correlated with outdoor concentrations in each fraction (R²=0.458 and 0.198, respectively). Indoor endotoxin concentrations in PM_2.5 were significantly higher in homes with tatami or carpet flooring and in homes with pets, and lower in homes that used air purifiers. Indoor endotoxin concentrations in PM_10‐2.5 were significantly higher in homes with two or more children and homes with tatami or carpet flooring. These results showed that the indoor endotoxin concentrations were associated with the household characteristics in addition to outdoor endotoxin concentrations.     

Computed tomography reconstruction from two transmission measurements for iodine-marked cancer detection

The authors invented the transXend detector, which measures X-rays as electric currents, and then gives the energy distribution of the X-rays after an unfolding process. In a previous paper, it was shown that the material thickness distributions can be estimated with the transXend detector by using reference points plotted from the electric current ratios, such as the I ₂/I ₁ ? I ₃/I ₁ graph, where I_i denotes the electric current measured by the i-th segment of the transXend detector. In this paper, the tomographic images of iodine, aluminum, and the acrylic those surround the other two materials are reconstructed from their material thickness distributions, which are estimated from two X-ray incidence directions. The X-ray event ratios are also used to estimate the material thickness distributions.     

Low-dose exposure energy-resolved X-ray computed tomography using a contrast agent with a high-energy K-edge

X-ray computed tomography (CT) with iodine contrast agent is widely employed to locate cancers. However, this method has shortcomings such as high-radiation dose exposure, iodine side effects, and a beam hardening effect. We have been working on the energy-resolved CT measurement method using a novel X-ray detection system, the “transXend” detector, which measures X-rays as electric currents and gives the energy distribution of incident X-rays after analysis. In the present study, we propose a method for low-dose exposure CT that involves the combination of the energy-resolved CT method, which is free from the beam hardening effect, and a harmless contrast agent with high-energy K-edge absorption, such as gold nanoparticles expected as a future contrast agent. Comparisons of radiation dose exposures as functions of aluminum filter thickness at the exit aperture of an X-ray tube and the K-edge energies of contrast agents are described.