性别视角下高职女大学生心理健康状况研究

通过对近五年高职新生UPI心理普查结果及心理咨询数据进行统计分析,了解高职女大学生的心理健康状况,发现高职女生心理问题主要表现在强迫倾向、缺乏自信、情绪问题这三个方面,女生整体心理健康状况显著低于男生,应有针对性的加强对女生的心理健康教育,为高职院校心理健康教育工作提供科学依据和建议。     

基于双层不确定推理的保护运行评价方法研究

针对地区电网继电保护装置的动作行为分析问题,建立了继电保护装置运行原因分析和责任部门评价两大规则体系.采用权值法形成的可信度赋予规则体系的概率模型,结合双层推理方式,形成双层不确定推理的过程,有效地反映了系统运行方式与保护逻辑动态过程的结合;采用基于概率模型的不确定推理方式实现责任部门评价过程,以提高评价过程的可靠性.现场试用过程表明:采用该方法评价继电保护装置的实际运行情况的结果正确,具有很好的实用价值.     

基材清洗工艺对SiO2/PET膜基结合强度的影响

采用磁控溅射工艺,在PET表面沉积Si O2薄膜,利用SEM观察镀膜的表面形貌,通过附着力测试仪检测Si O2/PET膜基的结合强度,研究基材PET表面清洗工艺对Si O2/PET膜基结合强度的影响。结果表明:结合强度因PET基材表面清洗工艺的不同而不同,其中经等离子清洗的膜基结合强度最大,达0.14MPa,分别较深度清洗、一般清洗和不清洗的膜基结合强度高7.83%,27.27%,55.56%;等离子清洗工艺参数对膜基结合强度有较大影响,随着清洗时间的增加、氩气流量的增大和清洗功率的提高,膜基的结合强度均呈现出先增大后减小的变化趋势。     

层间接触状态和横向力大小对车辙贡献率的影响

车辙贡献率是反映沥青路面各结构层车辙病害程度的一个主要参数,可用于指导沥青路面的设计和施工.利用三维有限元计算软件建立三维有限元模型用于理论分析,将有限元计算结果与理论解进行对比,验证了该三维有限元模型的可靠性.采用实测的轮胎接地压力,考虑不同层间接触状态和横向力大小,结合有限元计算的数据,分析了沥青路面结构层的车辙贡献率.结果表明:在层间完全连续状态下,横向力大小的选取不能简单地选取最大垂直轮胎接地压力的一定比例,而是要根据所研究的具体情况具体分析.在对沥青路面车辙贡献率的研究中,可以忽略层间接触状态,即假定层间完全连续.     

An effective thermal conductivity model for unsaturated compacted bentonites with consideration of bimodal shape of pore size distribution

An effective thermal conductivity model was proposed for unsaturated compacted bentonites with consideration of the bimodal shape of pore size distribution curves.The pores of soils were grouped into two dominant pore size modes corresponding to the intra-and inter-particle pores,and were simulated with randomly distributed spheroidal inclusions of different aspect ratios.With the assumption of preferential invasion of the wetting fluid(water)into pores of smaller sizes and by virtue of the analytical solution to the inhomogeneous inclusion problem in heat conduction,the model was developed using the Mori-Tanaka(MT),Ponte Casta?eda-Willis(PCW)and self-consistent(SC)homogenization approaches for different considerations of the interactions between pores and the solid phase.The proposed model is functions of the thermal conductivities of the solid,liquid and gas phases,porosity,the degree of saturation,the aspect ratios of pores and/or soil particles,and the fraction of the smaller group of pores.The proposed model was validated against five sets of laboratory measurement data on the MX-80,FEBEX,Kunigel-V1 and GMZ01 bentonites,showing a good agreement between the model predictions and the laboratory measurements.The responses of the model with respect to the geometries of pores and solid particles were examined.Compared to series-parallel structural models,the proposed model may overall exhibit better performance if proper homogenization schemes are adopted,but as an advantage,the model has clearer physical mechanisms and a smaller number of parameters.     

跌坎对消力池水力特性影响的试验研究

为研究跌坎在底流消能中的作用,依托某工程水力学模型,研究了跌坎对消力池内水流流态、临底流速及脉动压强的影响。结果表明:在来流量一定的情况下,随着跌坎高度的增加,消力池内流态会由底流依次演变为淹没混合流及淹没面流流态。加设跌坎可显著降低消力池前半段的临底流速,且跌坎越高,最大临底流速降幅越大,跌坎对消力池后半段的临底流速基本无影响;跌坎对脉动压强影响较大,随跌坎高度的增加,最大脉动压强先增大后减小;加设跌坎后,脉动压强和临底流速沿程先增大后减小,且脉动压力和临底流速的最大值位置基本在同一区域。     

Code-to-code comparison study on rotor aeromechanics in descending flight

This paper conducts the aeromechanics study using the two different rotorcraft computational structural dynamics (CSD) codes, CAMRAD II and DYMORE II, for the rotor in low-speed descending flight. The three test cases of the HART (Higher-harmonic control aeroacoustic rotor test) I -baseline, minimum noise, and minimum vibration- are considered in this study of the blade-vortex interaction (BVI) airloads, rotor trim, blade elastic deformations, and blade structural loads. The two prediction results are compared to each other for a code-to-code comparison study as well as to the measured data. Although CAMRAD II and DYMORE II use different theories and models, most of the prediction results are similar to each other and compared fairly well with the wind tunnel test data. For all the three test cases, the two rotorcraft CSD analyses show good prediction on the fluctuations of the section normal force (M²C_n) due to BVI, but both over-predict the trimmed collective pitch angle. The blade elastic deformations, such as flap deflection and elastic torsion deformation at the tip, are reasonably predicted by both rotorcraft CSD analyses. But, the CAMRAD II result using the multiple-trailer wake model with consolidation is slightly better than the DYMORE II prediction with the single wake panel model particularly for the elastic torsion deformation in the baseline case. In addition, CAMRAD II and DYMORE II both correlate reasonably the blade structural loads, such as flap bending, lead-lag bending, and torsion moments, with the measured data; however, the CAMRAD II results are moderately better than the DYMORE II predictions.     

斜视圆迹环扫SAR模式特性分析及成像方法简

Circular scanning SAR(CSSAR) is a new mode for fast large area SAR imaging by increasing the azimuth scanning speed. The squint CSSAR possesses the advantages that the side-looking CSSAR does not have due to its unique observing direction. However, the available signal characteristic analysis and imaging method for side-looking CSSAR become questionable when applied to the squint CSSAR. This paper establishes the echo range model and analyzes several parameters such as azimuth scanning speed, Doppler characteristics and azimuth resolution according to the moving feature of squint CSSAR. Furthermore, the internal relationship between the squint CSSAR and the classical stripmap mode is revealed. The range approximation model as well as the corresponding imaging method is analyzed. Computer simulation results validate the conclusions and the imaging method.     

青稞挤压糊化粉的研制

以青稞粉为原料,采用双螺杆挤压改性方法加工速食营养粉,研究挤压温度、螺杆转速和物料水分对物料品质的影响规律,并通过二次旋转正交组合实验（响应面实验）,优化营养粉工艺参数.结果表明,物料水分、螺杆转速和挤压温度对于青稞营养粉产品品质影响显著（P＜0.05）.响应面试验得出速食营养粉的较优加工条件：螺杆转速290 r/min,温度165℃和水分含量16.5％.在此优化条件获得青稞预糊化粉的各项指标为：膨化度3.14,吸水指数5.92,容重0.53,碘呈色度5.44.     

Effects of various fillers on sintering,microstructures and properties of Ca-Ba-Al-B-Si-O glass/ceramic composites简

Low-temperature sintering and properties of LTCC （low temperature co-fired ceramics） materials based on CaO-BaO-Al2O3-B2O3-SiO2 glass and various fillers such as Al2O3, silica glass, christobalite, AlN, ZrO2, MgO-SiO2, TiO2 were investigated. The results show that densification, crystallization, microstructures and dielectric properties of the composites are found to strongly depend on the type of filler. The densification process of glass/ceramic composites with various fillers is mainly from 600 ℃ to 925 ℃, and the initial compacting temperature of samples is 600 ℃. The initial rapid densification of samples starts at its glass softening temperature. LTCC compositions containing Al2O3, silica glass, AlN and MgO-SiO2 fillers start to have the crystallization peaks at 890, 903, 869 and 844 ℃, respectively. The crystallization peaks are believed as correlated to the crystallization of CaAl2SiO8, β-SiO2, Ca2Al2SiO7 and β-SiO2. The composite ceramic with Al2O3, silica glass and TiO2 ceramic have a better dense structure and better smooth fracture surface. Sample for Al2O3 has the lowest dielectric loss tanδ value of 0.00091, whereas the sample for MgO.SiO, has the highest dielectric loss tanδ value of 0.02576. The sample for TiO2 has the highest dielectric constant value of 14.46, whereas the sample for AIN has the lowest dielectric constant value of 4.61.