Factors affecting prior austenite grain size in low alloy steel

The effect of varying normalising and hardening temperatures on the prior austenite grain size in a low alloy Cr–Mo–Ni–V steel has been examined. An initial relative insensitivity of grain size to increasing austenitising temperature was observed followed by a sudden growth of grains at approximately 1000 °C. A detailed study of the precipitates in the steel showed the presence of a bimodal size distribution of vanadium carbides. The grain size increase is attributed to a decrease in volume fraction and an increase in size of V₄C₃ particles with increasing temperature.     

Identification of microstructural zones and thermal cycles in a weldment of modified 9Cr-1Mo steel

This paper presents the results of a study on the microstructural and microchemical variations in a multipass Gas Tungsten Arc weld (GTAW) of modified 9Cr-1Mo steel. The changes brought about in the steel due to the heating and cooling cycles during welding and the subsequent effects due to reheating effects during multipass welding are described. Detailed analytical transmission electron microscopy has been carried to study the type and composition of the primary and secondary phases in this steel. The systematic changes in microstructural parameters such as Prior Austenite Grain Size, martensite lath size, number density, size and microchemistry of carbides, have been understood based on the different transformations that the steel undergoes during the heating and cooling process. Based on the observed microstructure, an attempt has been made to identify distinct microstructural zones and possible thermal cycles experienced by different regions of the weldment.     

Effect of copper additions in directly quenched titanium–boron steels

The present study concerns the effect of copper additions on the microstructural evolution and mechanical properties of directly quenched Ti–B steels. Ti and B are added as microalloying elements with an aim of achieving adequate austenite hardenability and Cu is added to retard the austenite (γ) → ferrite (α) transformation. Therefore, the microalloying and Cu additions together allow the transformation of austenite to occur at a lower temperature, resulting in a finer microstructure containing martensitic constituents. The direct-quenching route is adopted with an aim of facilitating the nucleation of the constituent phases from the deformed austenite. In order to circumvent the hot-shortness due to the Cu addition, 0.79 wt% Ni has been added to one of the 1.5 wt% Cu microalloyed steels. The present study has demonstrated that the Ni-containing 1.5Cu–Ti–B steel is capable of providing an attractive combination of strength and ductility comparable to the high strength varieties of HSLA steels in directly quenched condition.     

Review on the fracture processes in nanocrystalline materials

An overview of experimental study, computer simulations and theoretical models of fracture of nanocrystalline materials is presented. The key experimentally detected facts on ductile and brittle fracture processes are discussed. Special attention is paid to computer simulations and theoretical models of nucleation and growth of nanocracks and nanopores in deformed nanocrystalline materials. Also, we discuss mechanisms for fracture suppression in such materials showing good ductility or superplasticity.     

Magnetostriction of binary and ternary Fe–Ga alloys

This article will review the development of the Fe–Ga (Galfenol) alloy system for magnetostriction applications including work on substitutional ternary alloying additions for magnetic property enhancement. A majority of the alloying addition research has focused on substitutional ternary elements in Bridgman grown single crystals with the intent of improving the magnetostrictive capability of the Galfenol system. Single crystals provide the ideal vehicle to assess the effectiveness of the addition on the magnetostrictive properties by eliminating grain boundary effects, orientation variations, and grain-to-grain interactions that occur when polycrystals respond to applied magnetic fields. In almost all cases, ternary additions of transition metal elements have decreased the magnetostriction values from the binary Fe–Ga alloy. Most of the ternary additions are known to stabilize the D0₃ chemical order and could be a primary contribution to the observed reduction in magnetostriction. In contrast, both Sn and Al are found to substitute chemically for Ga. For Sn additions, whose solubility is limited, no reduction in magnetostriction strains are observed when compared to the equivalent binary alloy composition. Aluminum additions, whose effect on the magnetoelastic coupling on Fe is similar to Ga, result in a rule of mixture relationship. The reviewed research suggests that phase stabilization of the disordered bcc structure is a key component to increase the magnetostriction of Fe–Ga alloys.     

Effect of preparation technique on the properties of Mo-containing Al-MCM-41

The Al-MCM-41 has been used as support to prepare Mo-containing catalysts. The 12- molybdophosphoric heteropoly acid (HPMo) is used as initial compound. The catalysts are synthesized by two different methods: incipient impregnation with aqueous solution of the acid and mechanochemical synthesis. The samples were tested in the reaction of the thiophene hydrodesulfurization after activation with mixture H₂ + H₂S. The effect of the preparation method of the catalysts on their physicochemical and catalytic properties has been studied. A partial destruction of the loaded compound is observed in mechanochemically treated sample whereas the aggregates are formed from the particles of different size in the impregnated sample. The specific surface area of the sample prepared by mechanical–chemical treatment decreases 2–3 times, while the total pore volume is about four times lower. The HDS activity is higher on the impregnated sample than on the mechanochemically treated one.     

Study of the hydrolysis and condensation of γ-Aminopropyltriethoxysilane by FT-IR spectroscopy

The hydrolysis and condensation reactions of γ-APS have been studied in different acid content aqueous solution by using Fourier Transform infrared (FT-IR) spectroscopy. The hydrolysis of γ-APS under the studied conditions can be followed by the increase of the ethanol band located at 882 cm⁻¹ and the decrease of the band due to the ρ(CH₃) of γ-APS molecules located at 959 cm⁻¹. Hydrolysis reaction is faster by increasing both H₂O and acid concentrations, and it is completed when 3 moles of H₂O per mole of γ-APS are used. The increase of the vibrational band located at 1146 cm⁻¹ shows that condensation of the hydrolysed γ-APS molecules take place forming linear chains in poorly cross-linked structures. Besides, both 8-membered cyclic siloxane formations and poorly cross-linked structures are formed and increase as the water and acid content are increased. On the other hand, highly connected cross-linked structures do not appear due to the steric hindrance of the non-hydrolysable aminopropyl group. The silanol band shows that hydrolysis is faster than condensation except for samples with the lowest H₂O content.     

Optimized hydrogen positions for aluminium and iron containing hydroxide minerals

The structures of a number of hydroxide and oxyhydroxide minerals have previously been reported without the hydrogen positions explicitly defined. Here we use two atomic scale computer simulation techniques, one based on classical ionic potentials, the other on density functional theory (DFT), to predict these positions. The aim is not only to provide data that can be used as the basis for future experimental structure optimizations but also model parameters that can be used to predict complex hydroxide structures. The efficacy of the approach is demonstrated through the comparison of predicted and experimental data for minerals whose hydrogen positions are known.     

Electrical characterization of carbon nanotube Y-junctions: a foundation for new nanoelectronics

A review on the syntheses and electrical characterization of Y-shaped multi-walled carbon nanotube morphologies is presented. Modified thermal CVD processes, using Ti precursors, are used to grow Y-junctions of different geometries and distribution of catalyst particles. It has been established that novel electrical switching behavior is feasible, where any one of the three branches of the Y-junction can be used for modulating the electrical current flow through the other two branches. Current blocking behavior, leading to perfect rectification, is seen which could be related to the interplay of the carrier lifetime and the transit time. The overall goal is to investigate the possibility of obtaining novel functionality at the nanoscale, which can lead to new device paradigms.     

LLDPE’s grown with Metallocene and Ziegler–Natta catalysts: events in the melt and FTIR analysis

LLDPE samples synthesized with Ziegler–Natta (ZN) and Metallocene (MT) catalysts have been analyzed to investigate a potential catalyst-dependent morphology and to find an explanation for the difficult processing of MT. Slow calorimetry at v = 0.02 K/min and IR at RT and in the melt are used. The differences between MT and ZN are assigned to their different composition, MT not having the linear segments, which are present in ZN. Slow calorimetry is effectively a drawing process of the melt with chain orientation followed by decay. The later event, characterized by an endotherm, ΔH _network, occurs at higher temperatures for MT, the presence of a regular distribution of methyl groups slowing down the process. The rocking, gauche, bending and stretching regions of the IR spectra are analyzed. The nascent MT has more strained bands in the rocking region. The wagging region reveals the more homogeneous environment of MT through the maximum absorbance at 1,368 cm⁻¹. Decomposition of bands is made for the rocking and wagging regions. The orthorhombic crystallinity, α_c (FTIR), measures the sum of long- and short-range orthorhombic order, the latter being obtained by α_c (FTIR)-α_c (X-rays). The values of α_c (FTIR) for MT and ZN are very similar in conditions of equilibrium. The justifications for the molecular origin of ΔH _network are presented: (i) the slow relaxation of long chains strained and oriented in the melt measured by other techniques, (ii) The correlation, for gels of a linear sample, made in different solvents, between the maximum drawability, λ_max, and ΔH _network in a slow T-ramp. The range is 80–270 for λ_max and 40–120 J/g for ΔH _network. (iii) The comparison of two traces of the same sample, between 140 °C and 270 °C, show that comparable events in the melt appear in the integrated absorbance and in the slow calorimetry signal. Analysis on thin films of the little-studied CH₂ stretching region reveals that their extinction coefficient, ε, and the shape of the bands are highly sensitive to the sample history, ε diminishing by a large factor in slowly crystallized samples. Events in the slow T-ramp, followed by a fast crystallization, on the other hand, leads to materials with standard characteristics. Slow calorimetry traces display more events (endothermic and exothermic) for MT than for ZN, a finding consistent with more flow irregularities during processing. Equilibrium conditions and better processing could be reached for MT by extending time in the melt or using higher temperatures.