基于三相幅度测量的相控阵天线快速校准方法

提出了一种基于三相幅度测量的相控阵天线快速校准方法。该方法将天线阵列进行分组,利用每种分组在三种配相下的阵面合成场幅度测量值,可解算出各个天线单元的初始幅相值。该方法仅需幅度测量,避免了相位测量误差影响单元幅相值的计算精度,而且所需幅度测量次数仅为(2N+1)次,可显著提高校准时效性。另外,利用分组思想,同时改变多个单元相位,使总辐射场的幅度变化显著,提升校准准确性。仿真结果表明:校准后相位均方根误差为2.2°,幅度均方根误差为0.2 dB。     

自制简易注浆器在境外隧洞工程施工中的应用

在乌干达卡鲁玛尾水隧洞工程前期施工中,由于国内注浆设备尚未到达,乌干达及周边国家难于买到,为了解决前期锚杆、小导管注浆等问题,项目部利用已进场的管材及乌干达能买到的材料、物资,成功地自行研制了简易锚杆、小导管注浆器,并得到了实际应用,从而保证了工程顺利开工,并取得了较好的经济效益。实际应用表明:该设备具有制作简单、操作方便、经济实用的特点。     

Visual Detection of Adenosine Triphosphate by Taylor Rising: A Simple Point-of-Care Testing Method Based on Rolling Circle Amplification

Rapid and sensitive point-of-care testing (POCT) is an extremely critical mission in practical applications, especially for rigorous military medicine, home health care, and in the third world. Here, we report a visual POCT method for adenosine triphosphate (ATP) detection based on Taylor rising in the corner of quadratic geometries between two rod surfaces. We discuss the principle of Taylor rising, demonstrating that it is significantly influenced by contact angle, surface tension, and density of the sample, which are controlled by ATP-dependent rolling circle amplification (RCA). In the presence of ATP, RCA reaction effectively suppresses Taylor-rising behavior, due to the increased contact angle, density, and decreased surface tension. Without addition of ATP, untriggered RCA reaction is favorable for Taylor rising, resulting in a significant height. With this proposed method, visual sensitive detection of ATP without the aid of other instruments is realized with only a 5 μL droplet, which has good selectivity and a low detection limit (17 nM). Importantly, this visual method provides a promising POCT tool for user-friendly molecular diagnostics.     

Structural dependence of microwave dielectric properties of spinel structured Mg2(Ti1-xSnx)O4 solid solutions: Crystal structure refinement,Raman spectra study and complex chemical bond theory

Mg₂(Ti_1-xSn_x)O₄ (x?=?0–1) ceramics were prepared through conventional solid-state method. This paper focused on the dependence of microwave dielectric properties on crystal structural characteristics via crystal structure refinement, Raman spectra study and complex chemical bond theory. XRD spectrums delineated the phase information of a spinel structure, and structural characteristic of these compositions were achieved with the help of Rietveld refinements. Raman spectrums were used to depict the correlations between vibrational phonon modes and dielectric properties. The variation of permittivity is ascribed to the Mg₂(Ti_1-xSn_x)O₄ average bond covalency. The relationship among the B-site octahedral bond energy, tetrahedral bond energy and temperature coefficient are discussed by defining on the change rate of bond energy and the contribution rate of octahedral bond energy. The quality factor is affected by systematic total lattice energy, and the research of XPS patterns illustrated that oxygen vacancies can be effectively restrained in rich oxygen sintering process. Obviously, the microwave dielectric properties of Mg₂(Ti_1-xSn_x)O₄ compounds were obtained (${\epsilon }_r$= 12.18, $Q\times f$?=?170,130?GHz, ${\tau }_f$?=??53.1?ppm/°C, x?=?0.2).     

机制砂混凝土耐磨性的主要影响因素分析及多因素计算模型

本文研究了砂类型、砂率、石粉含量和抗压强度对机制砂混凝土耐磨性的影响,建立了磨损量的多因素计算模型。结果表明:由于含石粉及具有更高的粗糙度和坚固性,石灰岩与辉绿岩机制砂制备的C30、C40混凝土耐磨性比河砂混凝土提高20%以上;在0.40~0.44范围内选取较低的砂率可获得较优的耐磨性;利用石粉含量为5%~11%(质量分数)的机制砂制备混凝土,石粉含量为9%时可获得最佳的混凝土耐磨性,微观分析表明此时混凝土密实度最佳;通过灰色系统理论确定了耐磨性影响因素的影响程度排序为:砂率R₃>压碎值R₂>粗糙度R₁>抗压强度R₅>石粉含量R₄>0.6;对比验证表明提出的混凝土磨损量多因素计算模型具有较高的预测精度和良好的适用性。     

Image Encryption Application of Chaotic Sequences Incorporating Quantum Keys

Machine Intelligence Research - This paper proposes an image encryption algorithm LQBPNN (logistic quantum and back propagation neural network) based on chaotic sequences incorporating quantum...     

Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

金属多孔材料喷墨制备法的研究与进展

喷墨三维打印作为金属增材制造技术的一种重要方法,已广泛应用于金属多孔材料的制备,具有成本低、操作简单、成型材料范围广、孔结构设计灵活性大,较好的制件精度和结构精细度等优点.系统地总结了钛及钛合金、不锈钢、镍基合金、铝合金等多孔材料喷墨三维打印技术制备工艺与组织结构的国内外最新研究进展、目前存在的问题,以及应用前景.     

5-二茂铁基噁唑的合成研究

以二茂铁甲醛和对甲苯磺酰基异氰(TOSMIC)为原料,经过Van Leusen反应,一步合成目标化合物5-二茂铁基噁唑,通过~1HNMR、~(13)CNMR和ESI-MS对其结构进行表征,并对影响收率的主要因素进行考察。结果表明,在物料比n(TOSMIC)∶n(二茂铁甲醛)为1.1∶1、反应溶剂为甲醇、K_2CO_3用量即n(K_2CO_3)∶n(二茂铁甲醛)为2.0∶1、反应温度为65℃、反应时间为8 h的最佳条件下,目标化合物收率达到74.7%。该方法具有原料廉价易得、反应操作简单、收率高等优点,具有一定的应用价值。