铸态Ti-20Zr-20Al钛合金动态压缩力学性能与断裂机制研究

采用X射线衍射仪、金相显微镜、分离式霍普金森杆和扫描电镜等手段研究了Ti-20Zr-20Al钛合金在动态压缩条件下的微观结构、力学性能和断裂机制。结果表明,Ti-20Zr-20Al铸态合金由Zr基体相和TiAl/Ti₃Al针状相组成; 随着应变率增加,合金的抗压强度增加,失效应变显著增加; Ti-20Zr-20Al合金的断裂机制为解理断裂; 随着应变率增加,试验压缩断裂后碎片总数增大,平均粒径减小。采用DID模型模拟的材料碎片尺度与实验结果比较吻合,Grady模型与实验结果的偏差较大。     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

不同制样方法对直流辉光放电质谱法测定氮化硼中27种杂质元素的影响

讨论了3种制样方法对直流辉光放电质谱法(dc-GDMS)检测氮化硼中的Na、Mg、Al、Si等27种杂质元素的影响。3种制样方法分别如下所示:方法1,直接把氮化硼压在铟薄片上;方法2,把氮化硼压在铟薄片上后,再盖上一层铟罩;方法3,把压碎后的氮化硼放在针状钽勺上。在优化的辉光放电参数下对比了3种不同制样方法对基体信号强度的影响。试验表明:在方法1中,当氮化硼尺寸约为3mm×3mm,厚度小于1mm时,基体¹¹B的信号可达1.8×10⁷ cps;在方法2中,选择铟孔大小合适的铟罩,基体¹¹B的信号可达1.0×10⁷ cps;方法3获得基体信号强度比方法1、方法2高一个数量级。大部分元素在中分辨率下可获得较好的结果,而对于在高分辨率下也较难分离的元素,可选择丰度较低的同位素在中分辨率下进行测定,如Ge选择⁷⁰Ge⁺,Se选择⁸²Se⁺,Cd选择¹¹¹Cd⁺,Sn选择¹¹⁹Sn⁺,Ag选择¹⁰⁹Ag⁺,Pt选择¹⁹⁴Pt⁺。氮化硼中的杂质元素含量可通过样品片中待测元素含量减去来自于铟薄片或钽勺中该元素贡献的含量来计算获得。将样品平行测定5次,相对标准偏差均在20%以内。对于Al、Si、Ti等元素的测定,3种制样方法的测定结果基本一致;方法1、方法2中检测到的In含量较大,使得铟中的Ni、Cu对氮化硼的测定值影响较大;方法3由于钽中Fe、Cu的贡献导致氮化硼中Fe、Cu的检测值较大,但方法3获得的基体信号强度大,可降低部分元素的检出限,如Cr、Mn、Ga、Ge等。综上所述,方法3为优选方法。     

Skidding analysis of angular contact ball bearing subjected to radial load and angular misalignment

Journal of Mechanical Science and Technology - Skidding is a phenomenon that frequently occurs in ball–raceway contact areas of bearings and often leads to their early failure. This paper...     

Influences of gap pressure on machining performance in radial ultrasonic rolling electrochemical micromachining

Microdimples as a typical surface texture has been widely used for improving the properties in tribology and heat transfer fields. Ultrasonically assisted     

Effect of Biochar as Reductant on Magnetizing-roasting Behavior of Pyrite Cinder

The effect of biochar substituted for anthracite as reductant on magnetizing-roasting pyrite cinder was investigated.The key of magnetizing-roasting is the gasification reaction between reductants and CO2.Since biochar could react with CO2 more rapidly at lower temperature,the reactivity of biochar is better than that of anthracite.The gasification of biochar could produce reducing condition ofφCO/(φCO+φCO2)about 10%-20% between 700-800 ℃,which is in accord with the atmosphere and temperature of Fe2O3 reduction.So it is beneficial to the reduction of iron mineral of pyrite cinder.Compared with anthracite,biochar could decrease the roasting temperature from825 to 750 ℃ and roasting time from 20 to 15min,which shows that a better effect of magnetization could be obtained in the condition of lower temperature and shorter time.Using biochar as reductant,iron concentrate extracted from pyrite cinder as about 64%iron grade could be produced,and the recovery is over 90% under the condition of above 90% grinding particle less than 0.045 mm and magnetic intensity of 0.124-0.194 T.     

Synthesis of highly efficient,structurally improved Li4SiO4 sorbents for high-temperature CO2 capture

Li₄SiO₄ sorbents for high-temperature CO₂ removal have drawn extensive attention owing to their potential application in carbon capture and storage (CCS). The major challenge in the application lies in the poor CO₂ capture performance under realistic conditions of low CO₂ concentrations, owing to the dense structure and poor porosity. In this work, Li₄SiO₄ sorbents were prepared with porous micromorphologies and large contact areas using a variety of organometallic Li-precursors, achieving fast CO₂ sorption kinetics, high capacity and excellent cyclic stability at a low CO₂ concentration (15?vol%). It was found that a high conversion of ~?74% was maintained for pure Li₄SiO₄ even after 100 sorption/desorption cycles. Moreover, by doping with Na₂CO₃ to reduce the CO₂ diffusion resistance, the conversion of the sorbent was further enhanced to 93.2%. The enhancement mechanism of alkali carbonate have been proven here to be ascribed to the formation of the eutectic melt of Li/Na carbonates, the existence and function of which has been confirmed in this study.     

一种基于场强差的GSM网络移动台定位法

提出了一种在GSM无线蜂窝网络中利用服务BS（基站）和MS（移动台）测量的场强差值对MS进行定位的方法。通过计算机的仿真结果表明，该方法能够较好地克服多径和不规则地形带来的场强起伏，达到较高的定位精度。通过提出的的算法，可以克服传统的利用GSM蜂窝网络对移动台定位的局限性，从而使利用GSM蜂窝网络对移动台位置定位的实现更简单。     

稠油微生物开采技术现状及进展

综述了用微生物方法开采稠油的技术现状与进展，论题如下。①概述。②基本方法：异源微生物采油，包括微生物吞吐和微生物驱；本源微生物采油压大港孔店油田的实例。③主要机理，包括产表面活性剂，降解稠油中重质组分及其他。④技术研究，包括机理性、可行性及经济效益研究，列举了国内外6个实例。⑤现场应用，包括国外1个、国内6个实例。⑥该技术的优势及问题。参22。