Electrocatalyst performance in industrial water electrolysers

Electrocatalyst materials used in industrial water electrolysis equipment must meet stringent requirements for long-term stability. Low electrode overvoltages must be sustained over prolonged periods of normal operation, including power interruptions. This paper presents an overview of the catalyst systems currently favoured for use in alkaline electrolyte. Performance data covering test periods exceeding 30 000 h are presented for representative commercial electrocatalysts. Results obtained in 100 000-A unipolar cells are correlated in detail with expectations based on measurements in laboratory and pilot-plant equipment.Particular attention is given to the effects of open-circuit conditions on electrode stability. An accelerated reverse-potential cycling test is described which allows identification of materials expected to withstand industrial operating conditions. It is found that the better materials which have been identified can be used with confidence, at least in electrolysers of the unipolar design in which potential variations encountered during current interruptions are modest.     

Multitemporal passive microwave mapping in MACHYDRO'90

MACHYDR0'90 was an experiment conducted in Pennsylvania in 1990 to study the synergistic use of remote sensors in multitemporal hydrologic studies. As part of this mission the pushbroom microwave radiometer was flown and used to produce brightness temperature maps. Verification studies and vegetation algorithms for mixed land cover areas are described     

FDTD solution of Maxwell's equations for an edge slot penetratingadjacent broadwalls of a finite wall thickness waveguide

The finite-difference time-domain (FDTD) method is applied to predict reflection coefficients for edge slots penetrating the adjacent broadsides of thick nailed rectangular X-band waveguides. Measured and calculated values S₁₁ are compared to experiment for waveguides terminated by shorted loads     

Microwave cavity perturbation technique: Part I: Principles

This report reviews the analysis used to extract the complex conductivity of a compound from a microwave cavity perturbation measurement. We intend to present a generalized treatment valid for any spheroidally shaped sample of arbitrary conductivity which is placed at either the electric or magnetic field antinode of the cavity. To begin with, we establish the relationship between the measured parameters and the conductivity for a spherical sample. Next, we extend these results to the case of spheroids; and for the first time, we cover all different configurations that one can possibly use to study an arbitrary conducting sample inside a cavity: in particular, all possible orientations of the sample with respect to the applied field are solved.     

Surface designing of polypropylene by critical monitoring of the grafting conditions

The grafting of acrylic acid onto electron beam‐irradiated polypropylene was carried out using preirradiation method. The stability of peroxy radicals was investigated by electron spin resonance. It was found that the decay of peroxy radicals is much faster at 70°C than at 40°C and ambient temperature. The grafting has been observed to be strongly dependent on the monomer dilution in the reaction medium. The grafting was ascertained by attenuated total reflectance (ATR). The distribution of grafts across the samples was monitored by infrared microscopy. It was found that the graft management is considerably influenced by composition of the grafting medium. The grafting involving pure monomer leads to the surface enrichment with the polyacrylic acid chains. The samples grafted in pure monomer led to much lower contact angles as compared to the diluted monomer solution. The swelling of the grafted samples also showed a trend that was governed by the graft management. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 546–553, 2006     

选择正确的PFC解决方案

本文用一种创新的方法提出了四种功率因数校正(PFC)电路设计。两种临界导通模式(CRM)升压．一种连续导通模式(CCM)升压和一种CCM单段回扫，并且推荐了基于功率要求、效率、失真程度、电路板空间和成本限制的解决方案。     

Analysis of tungsten and titanium migration during ESD contact burnout

A physical and chemical analysis of a machine model (MM) electrostatic discharge (ESD) failure in a silicon circuit was carried out. Focused ion beam (FIB) was used to make cross sections through the region of contact burnout. The resulting samples were analyzed using scanning electron microscopy (SEM) and two-dimensional (2-D) auger electron spectroscopic (AES) mapping. It is shown for the first time that both titanium (Ti) and tungsten (W) migrated throughout the melted silicon filament. Large pellets of the W plug were embedded in the bulk silicon but only on the cathode side of the junction. Mechanisms are discussed to explain these phenomena. These involve the melting of titanium disilicide (TiSi/sub 2/), dissolution of Ti and W in the molten silicon and the formation of W pellets through electromigration at temperatures below /spl sim/1800 K.     

Ab-initio primitive cell parameters from single convergent-beam electron diffraction patterns: a converse route to the identification of microcrystals with electrons.

A new method for the ab initio derivation of Buerger-reduced primitive cell parameters from coordinate measurements of spots on single convergent-beam electron diffraction (CBED) patterns is described, which does not involve trial-and-error. The pattern can be taken along any zone axis, and misorientations of the crystallite by as much as a few degrees are taken into account without loss of accuracy. This derivation of cell parameters by least-squares analysis of the measurements has been automated in a program called NRCBED. Present accuracy is about 1% on lengths and 2 degrees on angles, but could be significantly improved by modelling projector lens aberrations, or by using a microscope without a projector lens. With present technology, it is possible to obtain a CBED pattern and a semi-quantitative energy-dispersive X-ray (EDX) analysis simultaneously from a single microcrystal a few hundred Angstr?ms across. It becomes therefore possible to identify the material of the crystal on a single CBED pattern: a cell parameter database for known compounds is searched with the primitive cell parameters obtained in the above way, and with a mask describing the EDX results qualitatively. Feasibility is demonstrated on a crystallite of CeO2 500 Angstr?ms across. With this new approach, trial-and-error should disappear from the solution of other long-standing problems: interpretation of X-ray powder patterns for new compounds in the presence of impurity lines, or in the case of multiple phases should become straight-forward.     

Highly integrated direct conversion receiver for GSM/GPRS/EDGE with on-chip 84-dB dynamic range continuous-time /spl Sigma//spl Delta/ ADC

This paper describes a highly digitized direct conversion receiver of a single-chip quadruple-band RF transceiver that meets GSM/GPRS and EDGE requirements. The chip uses an advanced 0.25-/spl mu/m BiCMOS technology. The I and Q on-chip fifth-order single-bit continuous-time sigma-delta (/spl Sigma//spl Delta/) ADC has 84-dB dynamic range over a total bandwidth of /spl plusmn/135 kHz for an active area of 0.4 mm/sup 2/. Hence, most of the channel filtering is realized in a CMOS IC where digital processing is achieved at a lower cost. The systematic analysis of dc offset at each stage of the design enables to perform the dc offset cancellation loop in the digital domain as well. The receiver operates at 2.7 V with a current consumption of 75 mA. A first-order substrate coupling analysis enables to optimize the floor plan strategy. As a result, the receiver has an area of 1.8 mm/sup 2/.