Microstructure and damage evolution of SiCf/PyC/SiC and SiCf/BN/SiC mini-composites: A synchrotron X-ray computed microtomography study

SiC_f/PyC/SiC and SiC_f/BN/SiC mini-composites comprising single tow SiC fibre-reinforced SiC with chemical vapor deposited PyC or BN interface layers are fabricated. The microstructure evolutions of the mini-composite samples as the oxidation temperature increases (oxidation at 1000, 1200, 1400, and 1600?°C in air for 2?h) are observed by scanning electron microscopy, energy dispersive spectrometry, and X-ray diffraction characterization methods. The damage evolution for each component of the as-fabricated SiC_f/SiC composites (SiC fibre, PyC/BN interface, SiC matrix, and mesophase) is mapped as a three-dimensional (3D) image and quantified with X-ray computed tomography. The mechanical performance of the composites is investigated via tensile tests.The results reveal that tensile failure occurs after the delamination and fibre pull-out in the SiC_f/PyC/SiC composites due to the volatilization of the PyC interface at high temperatures in the air environment. Meanwhile, the gaps between the fibres and matrix lead to rapid oxidation and crack propagation from the SiC matrix to SiC fibre, resulting in the failure of the SiC_f/PyC/SiC composites as the oxidation temperature increases to 1600?°C. On the other hand, the oxidation products of B₂O₃ molten compounds (reacted from the BN interface) fill up the fracture, cracks, and voids in the SiC matrix, providing excellent strength retention at elevated oxidation temperatures. Moreover, under the protection of B₂O₃, the SiC_f/BN/SiC mini-composites show a nearly intact microstructure of the SiC fibre, a low void growth rate from the matrix to fibre, and inhibition of new void formation and the SiO₂ grain growth from room to high temperatures. This work provides guidance for predicting the service life of SiC_f/PyC/SiC and SiC_f/BN/SiC composite materials, and is fundamental for establishing multiscale damage models on a local scale.     

Structures and properties of chicken myofibrillar protein gel induced by microwave heating

Structures and properties of myofibrillar protein gel prepared at different power (300–800 W) were evaluated. Amino acid analysis demonstrated that changes in microwave power did not alter primary structure of gel. However, an increase in microwave power could change higher structures of gel. As microwave power increased, α-helix content decreased and β-sheet content increased. Increased microwave power probably facilitated protein to unfold and expose the internal groups, causing surface hydrophobicity and the formation of disulphide bonds were enhanced, which indicated changes in tertiary and quaternary structures of protein. At 500 W, gel had the best ultrastructure where surface morphology, springiness and water holding capacity reached the optimum. Our findings suggested that microwave at an appropriate power (500 W) could change higher structures of myofibrillar protein gel to achieve desired processing and quality protein gel characteristics.     

Large increase of Curie temperature in (110)-oriented La0.7Sr0.3MnO3 films

From the perspectives of scientific researches and practical applications, it is desirable to explore high operating temperature ferromagnetic films. The effect of biaxial strain on magnetic properties of (110)-oriented La_0.7Sr_0.3MnO₃ films was studied. High quality La_0.7Sr_0.3MnO₃ films were grown on (110)-oriented perovskite single crystal substrates using pulsed laser deposition, varying substrate-induced misfit strains from ??2.27–0.75%. A remarkable enhancement of Curie temperature has been achieved for (110)-oriented La_0.7Sr_0.3MnO₃ films clamped with small misfit strains (i.e., grown on LAST (110)). The enhanced Curie temperature of (110)-oriented La_0.7Sr_0.3MnO₃ films could be attributed to the misfit strain between the films and the underlying substrates and may have technological implication for applications at high temperature environments.     

Preparation of ZrC/SiC porous self-supporting monoliths via sol-gel process using polyethylene glycol as phase separation inducer

We present a straightforward method via sol-gel process using polyethylene glycol (PEG) as phase separation inducer to prepare zirconium carbide/silicon carbide (ZrC/SiC) porous monoliths. Organic/inorganic hybrid gels are prepared using zirconium oxychloride, furfuryl alcohol, and tetraethyl orthosilicate as major starting materials. In the presence of PEG, crack-free hybrid monoliths are obtained by drying the wet gels under ambient pressure, whereas in the absence of PEG, the wet gels break into pieces as expected. PEG plays a key role in maintaining the macroscopic shape of the monoliths. After ceramization at 1300–1500?°C, ZrC/SiC porous monoliths are obtained. SEM and mercury intrusion porosimetry data show that PEG also has strong influence on the microstructures of the monoliths. The compressive strengths of the ceramic monoliths are in the range of 0.3 to 0.7?MPa. And their compressive behavior starts to differ due to the changes in their microstructures, especially the pore structure.     

Preparation of biaxially textured Ce1-x(Y0.2Zr0.8)xOδ buffer layers on RABiTS NiW tapes by chemical solution deposition

Highly (100)-oriented Ce_1-x(Y_0.2Zr_0.8)_xO_δ (CYZO) films were prepared on biaxially textured NiW substrates by a chemical solution deposition approach using metal inorganic salts as starting materials. It has been found that both the preferential orientation and surface roughness of CYZO films decrease gradually with increasing of the doping percentage of Y³⁺ and Zr⁴⁺ ions. The epitaxial growth relationship of (220)_CYZO//(200)_NiW and [00?l]_CYZO//[001]_NiW was demonstrated by XRD texture measurement as well as atomic resolution STEM observation. XRD, Raman and XPS spectra results indicate that Y³⁺ and Zr⁴⁺ ions were indeed introduced into CeO₂ lattice to substitute Ce⁴⁺ ions and form cubic fluorite CYZO solid solution. Moreover, CeO₂ buffer layer can be endowed a strong enough capability to prevent element diffusion through co-doping of yttrium and zirconium, provided that an optimal doping ratio of them is adopted. This will provide a new approach to fabricating strong-barrier single buffer layer for coated conductor.     

Microwave dielectric properties of SrLa[Ga1−x(Mg0.5Ti0.5)x]O4 and SrLa[Ga1−x(Zn0.5Ti0.5)x]O4 (x = 0.2-0.8) ceramics

SrLa[Ga_1−x(R_0.5Ti_0.5)_x]O₄ (R = Mg, Zn) ceramics were prepared by a standard solid state sintering method. The single-phase ceramics with K₂NiF₄-type layered perovskite structure and I4/mmm space group were obtained, indicating that SrLa(R_0.5Ti_0.5) and SrLaGaO₄ can form the unlimited solid solutions. With increasing x for R = Mg and Zn, ε_r increases monotonously, the Qf value first increases and then decreases, while τ_f increases from a negative to a positive value. The optimized microwave dielectric properties were obtained as following: ε_r = 23.3, Qf = 89 400 GHz, τ_f = −0.8 ppm/°C for SrLa[Ga_0.6(Mg_0.5Ti_0.5)_0.4]O₄ and ε_r = 23.3, Qf = 76 200 GHz, τ_f = 0.2 ppm/°C for SrLa[Ga_0.7(Zn_0.5Ti_0.5)_0.3]O₄, indicating that the present solid solution ceramics are the promising candidates as microwave resonator materials for the telecommunication applications.     

Study on wax precipitation characteristics of wax deposit in pipes

Wax deposit properties are a significant concern in pipeline pigging during waxy crude oil transportation. In the present work, the impacts of flow conditions and oil properties on the wax precipitation characteristics of wax deposits are investigated. A flow loop apparatus was developed to conduct wax deposition experiments using four crude oils collected from different field pipes. The differential scanning calorimetry (DSC) technique was employed to observe the wax precipitation characteristics of crude oil and wax deposit. The results show that the wax content and the wax appearance temperature (WAT) of the deposits increase with shear stress and radial temperature gradient, and decrease with radial wax molecule concentration gradient near the pipe wall. The DSC tests on the wax deposits revealed that the deposit wax content is strongly correlated to the oil wax content. Furthermore, an empirical correlation was developed to predict the wax content and the WAT of the wax deposit. Verification of the empirical correlation using the different oils indicated that the average relative error of the wax content prediction and average absolute error of WAT prediction were 13.2% and 3.6°C, respectively.     

分子筛脱水吸附塔的结构应力与疲劳分析

综合考虑分子筛脱水吸附塔的结构、疲劳状况及管口载荷等因素,利用ANSYS对吸附塔进行结构应力与疲劳分析。计算结果表明:所建立的吸附塔整体模型合理;该结构在确保可靠性的基础上可降低制造成本;该设备能满足疲劳寿命的要求。     

Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.