A reappraisal of transition elements in linear elastic fracture mechanics

This article offers a detailed comparison of the transition elements described by P.P. Lynn and A.R. Ingraffea [International Journal for Numerical Methods in Engineering 12,1031–1036] and C. Manu[Engineering Fracture Mechanics 24,509–512]. The source of a numerical phenomenon in using Manu's transitionelement (TE) is explained. The effect of eight-noded TEs with differentquarter-point elements (QPE) on the calculated stress intensity factors (SIFs) isinvestigated. Strain at the crack tip is shown to be singular for any ray emanating from the crack tip within an eight-noded TE, but strain has bothr ^–1/2andr ^–1singularities, withr ^–1/2dominating for large TEs. Semi-transition elements (STEs) are defined and shown to have a marginal effect on the calculated SIFs. Nine-nodedtransition elements are formulated whose strain singularity is shown to be the same as that of eight-noded TEs. Then the effect of eight-noded and nine-noded TEs with collapsed triangular QPEs, and rectangular and nonrectangular quadrilateral eight-noded and nine-noded QPEs, is studied, and nine-noded TEs are shown to behave exactly like eight-noded TEs with rectangular eight-noded and nine-noded QPEs and to behave almost the same with other QPEs. The layered transition elements proposed by V. Murti and S.Valliapan [Engineering Fracture Mechanics 25, 237–258] areformulated correctly. The effect of layered transition elements is shown by two numerical examples.     

Passive Behavior of Ultra-Fine-Grained 1050 Aluminum Alloy Produced by Accumulative Roll Bonding in a Borate Buffer Solution

In this study, the effect of the ARB process on the passive behavior of ultra-fine-grained 1050 aluminum alloy in a borate buffer solution(p H 6.0) has been investigated. The result of the microhardness tests revealed that the microhardness values increase with an increasing number of ARB cycles. The potentiodynamic polarization plots revealed that the higher number of cycles for the specimens proceeds with the ARB process rather than annealing yield to lower corrosion and passive current densities and more noble corrosion potential values. Moreover, electrochemical impedance spectroscopy measurements showed that increasing the number of ARB cycles offers better conditions for forming the passive films.     

The Zn(S,O,OH)/ZnMgO buffer in thin‐film Cu(In,Ga)(Se,S)2‐based solar cells part II: Magnetron sputtering of the ZnMgO buffer layer for in‐line co‐evaporated Cu(In,Ga)Se2 solar cells

A ZnS/Zn_1‐xMg_xO buffer combination was developed to replace the CdS/i‐ZnO layers in in‐line co‐evaporated Cu(In,Ga)Se₂(CIGS)‐based solar cells. The ZnS was deposited by the chemical bath deposition (CBD) technique and the Zn_1‐xMg_xO layer by RF magnetron sputtering from ceramic targets. The [Mg]/([Mg] + [Zn]) ratio in the target was varied between x = 0·0 and 0·4. The composition, the crystal structure, and the optical properties of the resulting layers were analyzed. Small laboratory cells and 10 × 10 cm² modules were realized with high reproducibility and enhanced stability. The transmission is improved in the wavelength region between 330 and 550 nm for the ZnS/Zn_1‐xMg_xO layers. Therefore, a large gain in the short‐circuit current density up to 12% was obtained, which resulted in higher conversion efficiencies up to 9% relative as compared to cells with the CdS/i‐ZnO buffer system. Peak efficiencies of 18% with small laboratory cells and 15·2% with 10 × 10 cm² mini‐modules were demonstrated. Copyright © 2009 John Wiley & Sons, Ltd.     

Compositional engineering of chemical bath deposited (Zn,Cd)S buffer layers for electrodeposited CuIn(S,Se)2 and coevaporated Cu(In,Ga)Se2 solar cells

A comparative study of chemical bath deposition (CBD) of ZnS, CdS, and a mixture of (Cd,Zn)S buffer layers has been carried out on electrodeposited CuIn(S,Se)₂ (CISSe) and coevaporated Cu(In,Ga)Se₂ (CIGS) absorbers. For an optimal bath composition with the ratio of [Zn]/[Cd] = 25, efficiencies higher than those obtained with CdS and ZnS recipes, both on co‐evaporated CIGS and electrodeposited CISSe, have been obtained independent of the absorber used. In order to better understand the (Cd,Zn)S system and its impact on the increased efficiency of cells, predictions from the solubility diagrams of CdS and ZnS in aqueous medium were made. This analysis was completed by in situ growth studies with varying bath composition by quartz crystal microbalance (QCM). The morphology and composition of the films were studied using scanning electron microscopy (SEM) and X‐ray photoelectron spectra (XPS) techniques. Preliminary XPS studies showed that films are composed of a mixture of CdS and Zn(O,OH) phases and not a pure ternary Cd_{1 − x}Zn_xS compound. The effect of the [Zn]/[Cd] molar ratio on properties of the corresponding CISSe and CIGS solar cells was investigated by current voltage [J(V)] and capacitance voltage [C(V)] characterizations. The origin of optimal results is discussed. Copyright © 2008 John Wiley & Sons, Ltd.     

Study of a novel and simple method of generating binary mask for microprism fabrication

A new and simple method for generating binary masks for fabrication of gray scale micro-optical elements is proposed and examined. In this technique the main idea is superimposing two or more gratings with slightly different pitches that depend on the considered gray tone level. This causes generation of a chirped binary mask in which the openings widths are changed from a maximum to minimum through considered steps. Furthermore, to show its capability, it was applied to fabricate some microprisms. In addition, influence of proximity gap, and designation parameters on the surface quality were studied. It is shown that surface deterioration is effectively modified by optimizing the designation parameters. In comparison to other techniques, one of the advantages of this method is to have an assortment of pulse modulated masks that are able to create a variety of gray tone levels. Other advantages are ease in designation and implementation, and the fact that surface roughness could be smoothed effectively by aptly optimized parameters. Theoretical approach, simulation works, and experimental results are presented.     

Periodically focused modes in chains of dielectric spheres

We show that, theoretically, Brewster angle conditions for transverse magnetic polarized rays can be periodically reproduced in chains of spheres with index n?=?[Formula: see text] giving rise to lossless periodically focused modes with 2D period, where D is the sphere diameter. Using ray tracing for a spherical emitter with the diameter D we show that chains of spheres work as filters of such modes at 1.72?相似文献   

Shake table response and analysis of a concrete-filled FRP tube bridge column

The seismic performance of a concrete filled fiber reinforced polymer (FRP) tube (CFFT) bridge column was studied through shake table testing and nonlinear dynamic analyses of a one-fifth scale two-column bridge pier that also incorporated a conventional RC column. The FRP tube in the CFFT column was a prefabricated composite pipe with glass fibers aligned in ±55° with respect to the tube axis to provide both hoop and longitudinal strengths. The columns had nearly the same flexural capacities. The accumulated dissipated hysteresis energy of the CFFT column normalized by steel ratio was 1.6 times larger than that of the RC column; yet, it remained visibly damage free up to a drift ratio of 7%. The CFFT column failed due to FRP tube rupture under 8.4% drift ratio. The equivalent plastic hinge length of CFFT column was found to be more than twice that of the RC column, which implies larger spread of plasticity and smaller local ductility demands. The nonlinear dynamic modeling of the pier response using OpenSees led to very good agreement with the measured response of the pier under moderate and large-amplitude motions.     

Intrinsically high-Q dynamic AFM imaging in liquid with a significantly extended needle tip

Atomic force microscope (AFM) probe with a long and rigid needle tip was fabricated and studied for high Q factor dynamic (tapping mode) AFM imaging of samples submersed in liquid. The extended needle tip over a regular commercially available tapping-mode AFM cantilever was sufficiently long to keep the AFM cantilever from submersed in liquid, which significantly minimized the hydrodynamic damping involved in dynamic AFM imaging of samples in liquid. Dynamic AFM imaging of samples in liquid at an intrinsic Q factor of over 100 and an operational frequency of over 200?kHz was demonstrated. The method has the potential to be extended to acquire viscoelastic material properties and provide truly gentle imaging of soft biological samples in physiological environments.     

The synergistic effect of seawater's parameters on the corrosion rate of the austenitic stainless steel 304

In this article the corrosion rate of the austenitic stainless steel type 304, under the synergistic effect of environmental factors has been assessed via potentiodynamic polarization scan. Salinity, velocity, pH and temperature are the factors which induce effects on the corrosion rate of the considered metal. Quantitative analysis is applied using the full two-level factorial experimental design method, which results in the contribution value of each parameter in changing the quantity of average corrosion rate in both individual and synergistic cases. Besides this quantitative analysis, qualitative analysis has been used to predict the variation direction. These two analyses show the important role of the synergistic action, which changes the variation direction of corrosion rate and the contribution percentage of each parameter in varying the value of corrosion rate. Applying both these analyses can show the magnitude and quality of each parameter’s effect, which is remarkably valuable in marine applications.     

超音速火焰喷涂碳化物粒径不同的WC-10Co4Cr涂层在粗细磨粒下的磨损性能

改进的ASTM G65橡胶轮测试方法可采用220nm二氧化钛颗粒和368μm的砂粒分别在潮湿和干燥条件下使用。在由碳化物粒径不同(传统和亚微米)的两种粉末所制备的WC-CoCr涂层上开展试验,研究碳化物大小和磨损介质特性对涂层磨损性能的影响。采用扫描电镜对同一位置磨损前后的低倍和高倍形貌进行观察,并分析了涂层的磨损机理。结果表明:磨损机理取决于碳化物和磨粒的相对大小。在样品上进行磨损定量分析,通过调整碳化物尺寸可改善磨损性能,测试涂层的一些力学性能用于对比。