Temperature and pressure conditions for the appropriate performance of charge and mass resolutions in balloon-borne CR-39 track detector for the heavy cosmic rays

We experimentally determined the suitable conditions of temperature and air pressure for measuring charge and mass compositions of heavy cosmic rays using CR-39 track detectors during long-duration, high-altitude balloon flights. The experiments were carried out utilizing Fe ion beams from Heavy Ion Medical Accelerator (HIMAC). Changes in the track registration sensitivity with temperature were studied at temperatures between 213 and 293 K. The charge and mass shifts around Fe ions are possibly 0.11 cu (charge unit) and 0.47 amu (atomic mass unit) at the temperature deviation between 227 and 243 K at balloon altitude. Decrease in track registration sensitivity as air pressure decreases has been observed between 13 Pa and 27 kPa. The charge and mass shifts around Fe ions are inferred to be 0.02 cu and 0.09 amu, respectively, when pressure varies between 20 and 27 kPa. During balloon flight, air pressure drops below this; therefore, care must be taken to keep the temperature and air pressure of CR-39 detectors within acceptable limits.     

Discovery of a Novel Scaffold as an Indoleamine 2,3‐Dioxygenase 1 (IDO1) Inhibitor Based on the Pyrrolopiperazinone Alkaloid,Longamide B

Indoleamine 2,3‐dioxygenase 1 (IDO1) has emerged as a key target for cancer therapy, as IDO1 plays a critical role in the capacity of tumor cells to evade the immune system. The pyrrolopiperazinone alkaloid longamide B and its derivatives were identified as novel IDO1 inhibitors based on docking studies and small library synthesis. The thioamide derivative showed higher IDO1 inhibitory activity than longamide B, and displayed an activity similar to that of a representative IDO1 inhibitor, 1‐methyl‐tryptophan. These results suggest that the pyrrolopiperazinone scaffold of longamide B could be used in the development of IDO1 inhibitors.     

The Role of a Nonribosomal Peptide Synthetase in l‐Lysine Lactamization During Capuramycin Biosynthesis

Capuramycins are one of several known classes of natural products that contain an l ‐Lys‐derived l ‐α‐amino‐?‐caprolactam (l ‐ACL) unit. The α‐amino group of l ‐ACL in a capuramycin is linked to an unsaturated hexuronic acid component through an amide bond that was previously shown to originate by an ATP‐independent enzymatic route. With the aid of a combined in vivo and in vitro approach, a predicted tridomain nonribosomal peptide synthetase CapU is functionally characterized here as the ATP‐dependent amide‐bond‐forming catalyst responsible for the biosynthesis of the remaining amide bond present in l ‐ACL. The results are consistent with the adenylation domain of CapU as the essential catalytic component for l ‐Lys activation and thioesterification of the adjacent thiolation domain. However, in contrast to expectations, lactamization does not require any additional domains or proteins and is likely a nonenzymatic event. The results set the stage for examining whether a similar NRPS‐mediated mechanism is employed in the biosynthesis of other l ‐ACL‐containing natural products and, just as intriguingly, how spontaneous lactamization is avoided in the numerous NRPS‐derived peptides that contain an unmodified l ‐Lys residue.     

Fracture behaviour and numerical study of resistance spot welded joints in high-strength steel sheet

Cross tension tests of resistance spot welded joints with varying nugget diameter were carried out using 980 MPa high strength steel sheet of 1.6 mm thickness. In proportion, as nugget diameter increased from 3√t to 5√t (where t is thickness), cross tension strength (CTS) increased while fracture morphology simultaneously transferred from interface fracture to full plug fracture. In cases of interface fracture, circumferential crack initiation due to separation of the corona bond arose at an early stage of loading. The crack opening process without propagation was recognized until just before fracture and then the crack propagated to the nugget immediately in a brittle manner around CTS. In full plug fracture, main ductile crack initiation from the notch-like part at the end of sheet separation occurred with the sub-crack initiated at an early stage. The ductile crack propagated toward the HAZ and base material to form full plug fracture. The mode I stress intensity factor was considered as a suitable fracture parameter because the circumferential crack behaved pre-crack for brittle fracture in the nugget region at the final stage. Based on the FE analysis, the mode I stress intensity factor was calculated as 116 MPa √m at CTS as fracture toughness for the nugget. With respect to full plug fracture, ductile crack initiation behaviour from the notch-like part was expressed by concentration of equivalent plastic strain. On the assumption that the ductile crack arose in critical value of equivalent plastic strain, the value was calculated as 0.34 by FE analysis. Reasonable interpretation for interface fracture and full plug fracture in the resistance spot welded joint was proposed due to first crack initiation by stress concentration, brittle fracture by using mode I stress intensity factor, and ductile crack initiation by using equivalent plastic strain.     

EFFECT OF FLUIDIZING PARTICLE ON DRYING CHARACTERISTICS OF POROUS MATERIAL IN FLUIDIZED BED

The drying characteristics of porous material in fluidized bed were examined theoretically and experimentally. The brick ball was used as the sample and immersed in the fluidized bed. The glass beads were used as the fluidizing particles and the particle diameters were changed. When the pore diameter of sample was relatively large, the fluidizing particles were adhered on the sample surface. In the theoretical analysis, the heat and mass transfers in adhered particle layer were considered. The fluidizing particles were adhered on the sample surface during the earlier period of drying. The sample temperature largely decreased when the mass of adhered particle decreased. The calculated results are in good agreement with experimental data. The diameter of fluidizing particle had a small effect on the drying time. The excess increments in drying gas temperature hardly contributed to shortening the drying time.     

EFFECTS OF OPERATIONAL CONDITIONS ON DRYING CHARACTERISTICS IN CLOSED SUPERHEATED STEAM DRYING

The effects of operational conditions on the drying performance in closed superheated steam drying were examined theoretically and experimentally. The vapor generated from the sample was circulated in the drying chamber. In the theoretical analysis, the replacement of air with vapor in drying chamber and the convective vapor transfer in sample were considered. At the start of drying, the drying chamber was filled with air. As the drying proceeded, the air was replaced with the vapor generated from sample. The calculated results explained the characteristics of experimental data. The pore diameter of sample had little effect on the drying characteristics. During the internal evaporation period, the evaporation occurred in the narrow zone, which moved from the surface to the bottom of sample. The convective vapor transfer in sample had a significant influence on the drying performance. The excess increments in temperature and velocity of drying gas hardly contributed to shortening the drying time.     

Bioconversion of 1-adamantanol to 1,3-adamantanediol using Streptomyces sp. SA8 oxidation system

To efficiently produce 1,3-adamantanediol (1,3-ad(OH)₂) from 1-adamantanol (1-adOH), our stocks of culture strains and soil microorganisms were surveyed for hydroxylation activity towards 1-adOH. Among them, the soil actinomycete SA8 showing the highest hydroxylation activity was identified as Streptomyces sp. based on 16S ribosomal DNA sequence analysis. The reaction products were purified by silica gel column chromatography, and from NMR and MS analyses, they were identified as 1,3-ad(OH)₂ and 1,4-ad(OH)₂. Streptomyces sp. SA8 produced 5.9 g l^? 1 1,3-ad(OH)₂from 6.2 g l^? 1 1-adOH in culture broth after 120 h at 25 °C. Using resting cells, 2.3 g l^? 1 1,3-ad(OH)₂ was produced after 96 h of incubation at a 69% conversion rate. In both cases, 1,4-ad(OH)₂ was formed as a byproduct at a rate of about 15%. Strain SA8 also hydroxylated 2-adamantanol and 2-methyl-2-adamantanol.     

Evaluation of cost reduction potential for 1 kW class SOFC stack production: Implications for SOFC technology scenario

Recently, a commercial version of a residential solid oxide fuel cell (SOFC) system with a flat tubular cell has been developed. However, the system cost still remains very high, which is a barrier to its widespread use. In this study, the potential for cost reductions in SOFC stack production was investigated in order to contribute to the viability of the widespread use of such residential SOFC systems in future. A cost analysis of 700 W SOFC stack production based on a process integration modeling was conducted. The present bottom–up approach enabled us to perform a sensitivity analysis with a variety of parameters in terms of cell design, the production process and cell performance. This allowed us to investigate the effects of these factors on the production cost, thereby revealing the quantitative impact of each technological improvement on the cost reduction potential. The present analysis also revealed innovation pathways which could result in technology scenarios where residential SOFC systems could reach a break-even point in comparison with the baseload electricity cost. The analysis of the cost reduction potential presented here provides a useful viewpoint for developing a research strategy for state-of-the-art SOFC technology.     

An analysis of the length of hospital stay for cataract patients in Japan using the discrete-type proportional hazard model

We analyze the length of hospital stays of patients hospitalized for cataract and related diseases (Diagnosis Related Groups (DRG) 2041) in Japan, utilizing the data pertaining to 3436 patients on whom one-eye lens operations are performed. We use the discrete-type proportional hazard model to analyze variables that may affect the length of stay.     

Thermoreversible behavior of κ-carrageenan and its apatite-forming ability in simulated body fluid

Osteoconductive materials with self-setting ability have received much attention because their properties allow developing injectable materials for bone defects. Thermosensitive hydrogel with ability of bone-like apatite formation in a body environment is a candidate of injectable bone fillers with osteoconductivity because the apatite formation on materials is an essential to show osteoconduction. The present study focused on the development of a thermosensitive hydrogel through modifications of the sulphonic groups of the polysaccharide, κ-carrageenan, with potassium chloride (KCl) and calcium chloride (CaCl₂). We found that the gelation temperature of κ-carrageenan solutions increased with increasing amounts of K⁺ ions. Apatite formation was observed on the gel after exposure to simulated body fluid for 0.5 day when the gel was prepared with a molar ratio of Ca²⁺/sulfonic groups = 1.5. These results indicate that a thermosensitive κ-carrageenan hydrogel with apatite-forming ability was obtained through the incorporation of K⁺ and Ca²⁺ ions into the solution.