Effect of center block structure on the physical and rheological properties of ABA block copolymers. Part II. Rheological properties

The effect of the chemical structure of the center block on the rheological properties of ABA block copolymers with polystyrene end blocks has been investigated. The chemical structure of the center blocks investigated in the present paper are polybutadiene, polyisoprene, ethylene/butene copolymer, ethylene/propylene copolymer and polydimethyl-siloxane. The chemical structure of the center block was found to have a pronounced effect on the rheological properties of the ABA block copolymer melts. The long range relaxation times of these block copolymer melts increases with increasing incompatibility between the styrene block and the center block. However, the rheological properties of the block copolymers are not influenced significantly by the glass transition or the entanglement molecular weight of the center block.     

Enhanced strain hardening in elongational viscosity for HDPE/crosslinked HDPE blend. I. Characteristics of crosslinked HDPE

Blending a crosslinked high‐density polyethylene (xHDPE) enhances melt strength and strain hardening behavior in elongational viscosity of high‐density polyethylene (HDPE) to a great degree. Gel fraction of xHDPE has a stronger effect on the strain hardening than sol fraction, although sol fraction also enhances the strain hardening to some degree. Further, the xHDPE crosslinked by peroxide in a compression mold exhibits more pronounced effect than xHDPE by radiation, which is attributed to the difference in the amount of the gel fraction. The xHDPE, which enhances the strain hardening, has sparse crosslink points in the network. Moreover, it was found from linear viscoelastic measurements, such as oscillatory modulus and relaxation modulus, that the xHDPE is characterized as a critical gel, which was also supported by the result of tensile testing. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 73–78, 2002     

Fabrication of TiO2–SiO2 Photonic Crystals with Diamond Structure

Ceramic photonic crystals with diamond structure were fabricated using stereolithography and successive sintering. The green body of an epoxy resin incorporating 10 vol% TiO₂–SiO₂ was formed by stereolithography and then heated in air at 1100°–1400°C for 2 h. The sintered products maintained the diamond structure with a linear shrinkage ratio of about 57% and a porosity of 38%. The ceramic photonic crystal with eight unit cells showed a photonic band gap at the center frequency of 23.5 GHz. This fabrication method of three-dimensional (3D) ceramic photonic crystals is applicable to other 3D structural ceramics and does not require any molding techniques.     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.     

Formation, Characterization, and Hot Isostatic Pressing of Cr2O3-Doped ZrO2 (0,3 mol% Y2O3) Prepared by Hydrazine Method

In the ZrO₂-Cr₂O₃ system, metastable t -ZrO₂ solid solutions containing up to 11 mol% Cr₂O₃ crystallize at low temperatures from amorphous materials prepared by the hydrazine method. The lattice parameter c decreases linearly from 0.5149 to 0.5077 nm with increased Cr₂O₃ content, whereas the lattice parameter a is a constant value ( a = 0.5077 nm) regardless of the starting composition. At higher temperatures, transformation (decomposition) of the solid solutions proceeds in the following way: t (ss)→ t (ss) + m + Cr₂O₃→ m + Cr₂O₃. Above 11 mol% Cr₂O₃ addition, c-ZrO₂ phases are formed in the presence of Cr₂O₃. The t -ZrO₂ solid solution powders have been characterized for particle size, shape, and surface area. They consist of very fine particles (15–30 nm) showing thin platelike morphology. Dense ZrO₂(3Y)-Cr₂O₃ composite ceramics (∼99.7% of theoretical) with an average grain size of 0.3 μm have been fabricated by hot isostatic pressing for 2 h at 1400°C and 196 MPa. Their fracture toughness increases with increased Cr₂O₃ content. The highest K _Ic value of 9.5 MPa·;m^1/2 is achieved in the composite ceramics containing 10 mol% Cr₂O₃.     

Application of the Solvothermal Process in the Synthesis of High-performance Ag/γ-Al_2O_3 Catalysts

1 INTRODUCTION Since Cu-ZSM-5 was reported as an effective catalyst for the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of excess oxygen, the SCR of NOx has received much attention as a kind of potential technology for cleaning NOx in various oxygen-rich exhausts of diesel engine, lean burning gasoline engine and gas engine. Although a number of catalysts have been tested, to date, it still seems to be difficult to find a catalyst that is completely suit…     

Highly anisotropic thermal conductivity of mesogenic epoxy resin film through orientation control

To develop insulating materials with a high thermally conductive anisotropy, planarly aligned mesogenic epoxy (ME) resin film was fabricated by uniaxial coating on a hydrophobic polyethylene terephthalate substrate. Grazing incidence small-angle X-ray scattering (GISAXS) and transmission SAXS measurements exhibited that the films spontaneously formed uniaxially aligned monodomain-like smectic structures by curing on the hydrophobic substrate. Then, an in- and out-of-plane thermal conductivity of 10 and 0.048 W m⁻¹ K⁻¹ and outstanding thermal conductivity anisotropy of 208 have been confirmed, respectively. The ME resin films with high thermal conductivity can be applied as insulating materials for multiple-layer electrical and electronic devices.     

Repeatedly foldable AMOLED display

In this study, a 5.9‐inch foldable active‐matrix organic light emitting diode (AMOLED) display was developed. A folding test was performed repeatedly. The display survived the folding test (100,000 folds) with a curvature radius of 2 mm. To protect an organic light emitting diode (OLED) against moisture, inorganic passivation layers are provided on the upper and lower sides of the flexible display. Using our transfer technology, high density passivation layers can be obtained. The measured water vapor transmission rate of the layer is 7 × 10^?6 g/m²?day or less, which improves OLED reliability. With these techniques, we have developed a book‐type display, which is repeatedly foldable like a book, and a tri‐fold display including a display area, which is foldable in three.     

The effects of amino-acid mutations on specific interactions between urokinase-type plasminogen activator and its receptor: Ab initio molecular orbital calculations

During cancer invasion, the binding of urokinase-type plasminogen activator (uPA) to its receptor (uPAR) on the surface of a cancer cell is considered a trigger for invasion. Here, we present a stable structure of the solvated complex formed between uPA and uPAR (uPA-uPAR) and investigate the specific interactions between uPA and uPAR by ab initio fragment molecular orbital (FMO) calculations. The result indicates that the electrostatic interactions between the charged amino acid residues existing in both uPA and uPAR make a large contribution to the binding between uPA and uPAR. In particular, Lys23, Lys46, Lys98 and Lys61 of uPA are found to have strong attractive interactions with uPAR. To elucidate the effect of these residues on the interactions between uPA and uPAR, we substituted each of them with the uncharged amino acid Leu and investigated the interactions between the mutated uPA and wild-type uPAR. The interaction energies indicate that Lys46 and Lys98, which bind uPA to the rim of the central ligand-binding cavity of uPAR, make greater contributions to the binding between uPA and uPAR than Lys23, which is positioned at the bottom of the ligand-binding cavity of uPAR. The effect of hydrating water molecules located between uPA and uPAR is also investigated to be significant for the specific interactions between uPA and uPAR. These results are expected to be informative for developing new peptide antagonists that block the binding of uPA to uPAR.     

Damage to seagrass and seaweed beds in Matsushima Bay,Japan, caused by the huge tsunami of the Great East Japan Earthquake on 11 March 2011

Damage to seagrass and seaweed beds caused by the huge tsunami of the Great East Japan Earthquake on 11 March 2011 was investigated in Matsushima Bay, Miyagi Prefecture, Japan, by comparing satellite images taken before the tsunami in November 2009 and after the tsunami in May 2011. The results showed that the tsunami destroyed 220 ha of seagrass and seaweed beds, from 320 ha in 2009 to 100 ha just after the tsunami. Zostera marina beds on the sandy and muddy bottom were rather severely damaged compared with brown seaweed beds of Sargassum horneri on the rocky substrate. Substrates of the beds and directions of the tsunami seem to be responsible for the magnitude of the damage to the beds. Maps of the spatial distributions of the beds before and after the tsunami can provide information for the restoration of seagrass and seaweed beds as natural infrastructures of coastal fisheries resources.