A compact full MMIC module for Ku-band phase-lockedoscillators

A compact Ku-band phase-locked oscillator module has been developed in a full MMIC (monolithic microwave integrated circuit) configuration. The module includes an MMIC voltage-controlled oscillator, an analog frequency divider, and interstage amplifiers. The constituent monolithic chips are integrated in a very small single-package module and operate at the target frequencies without any external trimming or matching network. The oscillator is tuned more than 1 GHz with a constant output amplitude. The frequency-divided output is also obtained over the whole tuning range. Spurious output is not found at any frequency up to 22 GHz. In spite of the very low-Q factor of GaAs monolithic circuitry, the oscillator phase noise exhibited is less than -80 dBc/Hz, due to the high-gain, high-speed phase lock     

The development of MHD cold wall channels in the oil-fired condition

The durability of a cold wall MHD generator consisting of metal electrodes and alumina-coated peg insulators was experimentally examined in the oil-fired MHD condition with the additive of SO₂ corresponding to S = 0.54 wt%. The structure of the electrode wall and various anode and cathode materials were tested, with particular reference to developing long-life electrodes. It was clarified that Pt, SHOMAC (28.8 Cr−1.9 Mo) and SUS-304 as anodes and W---Cu (70 W−30 Cu) and WC---Ag (60 WC−40 Ag) alloys as cathodes were promising for durability and that the structure of an anode divided into two elements connected to each other with an SnO₂ resistor was very useful for uniformity of the anode corrosion pattern and the inter-anode voltages. It is reasonable to expect, from the test results, that the lifetime of a cold wall MHD generator in an oil-fired commercial plant will be over 4000 h, and therefore, a foundation for its commercial use has been established.     

Systematic analysis of neutron yields from thick targets bombarded by heavy ions and protons with moving source model

A simple phenomenological analysis using the moving source model has been performed on the neutron energy spectra produced by bombarding thick targets with high energy heavy ions which have been systematically measured at the Heavy-Ion Medical Accelerator (HIMAC) facility (located in Chiba, Japan) of the National Institute of Radiological Sciences (NIRS). For the bombardment of both heavy ions and protons in the energy region of 100–500 MeV per nucleon, the moving source model incorporating the knock-on process could be generally successful in reproducing the measured neutron spectra within a factor of two margin of accuracy. This phenomenological analytical equation is expressed having several parameters as functions of atomic number Z_p, mass number A_p, energy per nucleon E_p for projectile, and atomic number Z_T, mass number A_T for target. By inputting these basic data for projectile and target into this equation we can easily estimate the secondary neutron energy spectra at an emission angle of 0–90° for bombardment with heavy ions and protons in the aforementioned energy region. This method will be quite useful to estimate the neutron source term in the neutron shielding design of high energy proton and heavy ion accelerators.     

Modeling of a power electronic converter for EMC in the conduction emission frequency band

With the advancement of high‐frequency switching devices, electromagnetic interferences (EMI) have become problems in power electronic converter designs. It is necessary for an electromagnetic compatibility (EMC) design to prospect and consider its possible EMI levels. This paper describes how to compute effects from a power converter to an object point to reduce conduction EMI noises effectively by an appropriate design. Modeling techniques for converter elements are discussed for a model in the conduction emission frequency band by the parameter tuning method and for line constants by an analytical derivation. Then a derived model is simulated for harmonic distributions of loop currents and their magnetic fields. © 2002 Scripta Technica, Electr Eng Jpn, 139(1): 44–50, 2002: DOI 10.1002/eej.1145     

Stereoscopic synthesized brain-surface imaging with MR angiography for localization of a peripheral mycotic aneurysm: case report

A patient with subacute bacterial endocarditis and a peripheral mycotic aneurysm is presented. We used a combined multi-slice surface anatomy scanning (SAS) and contrast-enhanced MR angiography image to determine the exact location of the small lesion by applying a skin marker on the scalp and visualizing the relationship of the marker to the brain surface structures and to the lesion. This technique was useful for the removal of a small peripheral aneurysm using only a limited craniotomy.     

Change of characteristics of desulfurization and denitrification by combustion flue gas composition and electrode configuration under pulsed corona discharge

Laboratory-scale and parametric experiments of SO₂ and NO_x removal from the simulated combustion gas by pulsed corona discharge have been performed by changing the combustion gas composition and temperature, the electrode configuration of plasma reactor, and the polarity of high-voltage electrode. The following results are obtained: 1) the higher the concentration of H₂O and O₂, the higher the efficiency of desulfurization and denitrification at the same specific input; 2) the pulsed corona discharge with a voltage pulsewidth as short as 200 ns of negative polarity shows the possibility to attain almost 90 percent deSO_x and deNO_x efficiency at the specific discharge input of 20 J/g, which is almost the same as the specific input in the electron-beam process; 3) the deNO_x characteristics show a little temperature dependence in the range of 70 to 130°C, but the deSO_x efficiency increases rapidly in the temperature region below 100°C suggesting the thermochemical dependence of deSO_x reaction; 4) when desulfurization and denitrification proceed, the white dendritic powder deposits on the plasma reactor whose composition is identified to be 49 mol% (NH₄)₂SO₄ and 47 mol% of 2NH₄NO₃ · (NH₄)₂SO₄, and the ratio of SO₂, NO and NH₃ of the deposit is almost equal to that of supplied gas.     

A finite element parametric study on the mechanical properties of J-shaped steel hysteresis devices

The present paper discusses the mechanical properties of J-shaped steel hysteresis devices, abbreviated to “J-dampers”, interposed between the upper structure of a spatial structure and its substructure. The mechanical properties of a J-damper, which are characterized by its key geometrical and material parameters, are evaluated through parametric analyses using an in-house Finite Element program. The hysteresis behavior of a J-damper is also modeled by a bi-linear elasto-plastic hysteresis model with the strain-hardening effect. Its elastic stiffness, yield strength and dimensionless hardening ratio, which are expressed as functions of the parameters, are formulated on the basis of mathematical models and the results of parametric studies. Finally, some remarks relevant to the application of the proposed hysteresis model are made for the design of the J-damper.     

Reexamination of grain-boundary sliding by diffusion

Steady-state sliding of grain boundaries is discussed by taking into account the change in the potential energy of an applied stress, when the sliding occurs by diffusional accommodation. The present analysis enables us to derive the sliding rates at boundaries of various shapes in a simple manner without knowing local stress fields. Sliding rate of a boundary containing second phase particles is also derived by similar calculations. The results are compared with previous calculations by other investigators, and it is found that the resultant expressions for the sliding rates are essentially identical to those derived from more complex analyses.     

Formation of dityrosine and other fluorescent amino acids by reaction of amino acids with lipid hydroperoxides

Formation of fluorescence by the reaction of various amino acids with lipid hydroperoxides,i.e., linoleic acid 13-monohydroperoxide, methyl linoleate 13-monohydroperoxide and phosphatidylcholine hydroperoxide, in the presence of methemoglobin was investigated. Two types of fluorescence were produced: fluorescent dityrosine (3,3′-dityrosine) from tyrosine, and unidentified fluorophores with α- and ε-amino groups of various amino acids. While the former was stable after treatment with borohydride, the latter fluorophores were readily destroyed. The rate of dityrosine formation was rapid, and the yield of dityrosine was dependent on the concentrations of tyrosine and the lipid hydroperoxides. Butylated hydroxytoluene and tocopherol inhibited the formation of dityrosine, but did not affect the formation of fluorophores on the amino groups. Dityrosine appears to be formed by radical reaction of the lipid hydroperoxides, while the other fluorophores seem to be created by nonradical mechanisms.