Extensive Study of Underlap Length Effect for 3-D SOI FinFET to Achieve High Switching Ratio and Low Power

Silicon - The primary purpose of this work is to study the effect of symmetric and asymmetric variation of underlap regions both on source and drain side of 3D SOI n-FinFET. Underlap length is...     

Gas hold-up in non-newtonian solutions in a bubble column with internals

Bubble characteristics and gas hold-up were studied in a two phase (air-aqueous CMC solution) bubble column provided with helical coils and straight tubes as internals. The effects of superficial gas velocity, rheological properties, and volume fraction covered by the internals, on gas hold-up were studied. Hold-up values determined directly and by simultaneous pressure drop measurements matched well. Enhancement of gas hold-up values up to 55 per cent was achieved in systems using internals. The gas hold-up results were also compared with the values obtained from correlations reported in the literature.     

Simulation and analysis of extractive distillation process in a valve tray column using the rate based model

Valve trays are becoming popular in the chemical process industries owing to their flexibility to handle a wide range of vapor throughputs. Using the rigorous rate based model, the importance of the non-equilibrium approach is demonstrated for a typical extractive distillation process in a Glitsch V-1 valve tray column. Simulation results based on an in-house developed code indicated that the rate based model predictions for a valve tray column operation showed significant differences relative to the equilibrium model. Even small errors in product purities translated into nonoptimal feed stage locations and inaccurate number of stages required. The counter-intuitive effect of high reflux ratio on separation is explained.     

Alkylation of Benzene with Isopropyl Alcohol over SAPO-5 Catalyst in an Integral Pressure Reactor

The alkylation of benzene with isopropyl alcohol was studied in an integral pressure reactor over silicon substituted aluminophosphate molecular sieves, SAPO-5. The influence of various process parameters such as temperature, pressure, time on stream, weight hourly space velocity, and mole ratio of reactants on cumene yield and selectivity were investigated. The activity of SAPO-5 was compared with that of Hbeta for this reaction under similar conditions and in the same reactor. At pressures higher than atmospheric, almost the theoretical maximum yields of cumene were achieved on this SAPO-5. Among the diisopropyl benzenes formed by the alkylation of cumene, the meta-isomer was found to form in a significant amount followed by the para-isomer. The ortho-isomer with relatively high strain energy of 4.26 kcal/mol was almost negligible. The cumene yield goes through a maximum in the temperature range 498-543 K studied. Cumene selectivity was found to decrease at higher temperatures, higher pressures and lower benzene to isopropanol mole ratios.     

Prediction of the hydraulic diffusivity from pore size distribution of concrete

A model is presented in this work through which variation of hydraulic diffusivity of concrete with relative water content can be obtained from pore size distribution as an input. The specific water capacity and hydraulic conductivity of concrete are expressed in terms of pore size characteristics, considering laminar flow due to capillary suction through tortuous elliptic tubes, oriented equally in three orthogonal directions. Hydraulic diffusivity being the ratio of hydraulic conductivity and specific water capacity is thus expressed in terms of pore size characteristics. The input pore size distributions have been determined experimentally for normal strength concrete mixes through mercury intrusion porosimetry. Using the model the variation of hydraulic diffusivity with relative water content is determined for three cases viz. 1) ideal continuous wetting, 2) ideal continuous drying and 3) random access of pores by water. These results are then compared with an experimentally obtained variation.     

Optimisation of four-sensor probes for measuring bubble velocity components in bubbly air-water and oil-water flows

In a previous paper Lucas and Mishra (2005) [3] a local four-sensor conductance probe was introduced to measure the velocity vectors of dispersed bubbles in bubbly two-phase flow in which the continuous phase is water. There are a very limited number of alternative methods available for bubble velocity vector measurement with which results from, for example, computational fluid dynamic models can be compared and so the four-sensor probe technique is of interest to the multiphase flow community. In the previous paper [3] a mathematical model was presented to calculate the velocity vector of each gas bubble from seven time intervals which were measured using the output signals from each of four ‘needle’ conductance sensors located within the probe. In the present paper, a new technique for making the local four-sensor probe is introduced to minimise interference with the measured bubbles. A new signal processing method is presented using criteria to ensure that (i) the group of sensor signals from which the bubble velocity vector is to be determined are all produced by the same bubble and (ii) bubbles which contact the local four-sensor probe in an ambiguous manner are ignored. The accuracy with which the locations of each of the rear sensors in the probe relative to the lead sensor can be measured influences the accuracy with which the bubble velocity vector can be measured. However, the degree to which the accuracy of the measured velocity vector is affected by errors in the measured probe dimensions is dependent upon the geometrical arrangement of the four sensors within the probe. Experimental results and an error analysis are presented which show that the susceptibility of the velocity vector measurement technique to errors in the measured probe dimensions is reduced if the geometrical arrangement of the four sensors is optimised. As a result of this initial work, an optimised probe, known as the P30 probe, was designed and built and results obtained from the P30 probe in swirling oil-in-water bubbly flow are presented. A probe calibration factor is defined in this paper which can be interpreted as a measure of the interference of a probe with the motion of the bubbles with which it interacts. For the probes described in this paper the calibration factor was found to be much closer to unity than for previous four-sensor probes described in the literature (e.g. [3]) suggesting that these new probes have a much smaller effect on the bubbles’ motion than previous probes.     

Fuzzy logic techniques for navigation of several mobile robots

In this paper, navigation techniques for several mobile robots as many as one thousand robots using fuzzy logic are investigated in a totally unknown environment. Fuzzy logic controllers (FLC) using different membership functions are developed and used to navigate mobile robots. First a fuzzy controller has been used with four types of input members, two types of output members and three parameters each. Next two types of fuzzy controllers have been developed having same input members and output members with five parameters each. Each robot has an array of ultrasonic sensors for measuring the distances of obstacles around it and an infrared sensor for detecting the bearing of the target. These techniques have been demonstrated in various exercises, which depicts that the robots are able to avoid obstacles as well as negotiate the dead ends and reach the targets efficiently. Amongst the techniques developed, FLC having Gaussian membership function is found to be most efficient for mobile robots navigation.     

Sliding mode controller design via delay-dependent H∞ stabilization criterion for load frequency regulation

This work presents a control approach based on sliding-mode-control (SMC) to design robust H∞ state feedback controllers for load frequency regulation of delayed interconnected power system (IPS) with parametric uncertainties. Considering both state feedback control strategy and delayed feedback control strategy, two SMC laws are proposed. The proposed control laws are designed to improve the stability and disturbance rejection performance of delayed IPS, while stabilization criteria in the form of linear matrix inequality are derived by choosing a Lyapunov–Krasovskii functional. An artifcial time-delay is incorporated in the control law design of the delayed feedback control structure to enhance the controller performance. A numerical example is considered to study the control performance of the proposed controllers and simulation results are provided to observe the dynamic response of the IPS.     

A Multi-Criteria Route Selection Method for Vehicles Using Genetic Algorithms Based on Driver’s Preference

Wireless Personal Communications - Finding the best path between a given source and a destination in a road network is an important problem. It has its applications in various map services and...