Mechanical properties of polyaniline

In spite of extensive electrical characterization of polyaniline, the information on its mechanical properties is missing in the literature. Complex Young's modulus of polyaniline compressed into pellets was measured at room temperature and an influence of preparation conditions of the polyaniline pellets on mechanical properties was studied. Young's modulus of PANI hydrochloride pellets was 0.9 ± 0.2 GPa and that of polyaniline base 1.3 ± 0.2 GPa. These values are comparable with common polymers, such as bulk polystyrene, 1.8 ± 0.1 GPa, or compressed polystyrene powder, 0.80 ± 0.02 GPa. Modulus of polyaniline is independent of the compression pressure above 300 MPa, the time of compression had no effect.     

The carbonization of colloidal polyaniline nanoparticles to nitrogen‐containing carbon analogues

The carbonization of nanostructures afforded by conducting polymers represents a new route to the preparation of functional nanostructured carbons. The exposure of colloidal polyaniline particles stabilized with poly(N‐vinylpyrrolidone) or silica nanoparticles at 650 °C in inert atmosphere led, in both cases, to nitrogen‐containing carbonaceous materials with specific surface areas of 200 and 205 m² g^?1, respectively, and conductivities of 8.3 × 10^?7 and 1.9 × 10^?10 S cm^?1, respectively. The latter material contained 77 wt% of silica. The original particulate nanostructure of the samples was preserved after carbonization. The carbon‐to‐nitrogen atomic ratio was 7.2 and 7.9; the nitrogen content in the carbonized polyaniline–poly(N‐vinylpyrrolidone) particles was 10.8 wt%. Thermogravimetric analysis in air revealed their stability to be up to 500 °C. This is comparable with commercial multi‐wall carbon nanotubes, which have similar areas of application. The nitrogen‐containing carbons are potentially useful as supports for catalysts and in applications where carbon of higher hydrophilicity would be of benefit. Copyright © 2010 Society of Chemical Industry     

Polypyrrole and polyaniline prepared with cerium(IV) sulfate oxidant

The conducting polymers, polypyrrole and polyaniline, were synthesized by chemical oxidative polymerization of the corresponding monomers in 0.1 M sulfuric acid using cerium(IV) sulfate as the oxidant at mole ratios of oxidant-to-monomer ranging from 0.5 to 3. The yields of the oxidation products were determined, and the samples were characterized with respect to their elemental composition, molecular structure, and morphology. The conductivity of polypyrrole prepared in 0.1 M sulfuric acid, 10^?1 to 10⁰ S cm^?1, was higher compared with the conductivity of polyaniline prepared under the same conditions, 10^?3 to 10^?1 S cm^?1. The loss of mass after deprotonation with ammonium hydroxide is reported, and discussed in terms of the type of protonation as also reflected by FTIR spectroscopy. The conductivity of polypyrrole bases remained at relatively high level, 10^?5 to 10^?3 S cm^?1, while PANI bases became non-conducting, 10^?12 to 10^?10 S cm^?1. The polymers had a granular morphology in all cases.     

Partition coefficients of environmentally important phenols in a supercritical carbon dioxide-water system from cocurrent extraction without analysis of the compressible phase

Partition coefficients of phenol, salicylic acid, and several environmentally important chloro- and nitrophenols in a supercritical CO2-water system were measured using direct cocurrent extraction of aqueous solutions of the individual solutes with CO2. Partitioning data on the nitrophenols and salicylic acid were obtained for the first time. To bypass the troublesome and error-prone analysis of the CO2-rich phase, the present method employed only the solute concentrations in the aqueous phase before and after extraction to determine the partition coefficient. Unlike most previous engineering studies of phenol partitioning in a CO2-water system, the concentrations of phenolic solutes approached infinite dilution in both phases. This makes the results relevant to analytical-scale SFE of environmental water samples with CO2. Because of effective infinite dilution of the solutes, the partition coefficients provide a direct measure of relative CO2-philicity/hydrophilicity of the individual phenols. Compared to the octanol-water partition coefficients of substituted phenols, the CO2-water partition coefficients are more sensitive to substitution in the position neighboring the hydroxyl group.     

A new wavelet-based measure of image focus

We present a new measure of image focus. It is based on wavelet transform of the image and is defined as a ratio of high-pass band and low-pass band norms. We show this measure is monotonic with respect to the degree of defocusation and sufficiently robust. We experimentally illustrate its performance on simulated as well as real data and compare it with existing focus measures (gray-level variance and energy of Laplacian). Finally, an application of the new measure in astronomical imaging is shown.     

Analysis of the reaction mechanism and substrate specificity of haloalkane dehalogenases by sequential and structural comparisons

Haloalkane dehalogenases catalyse environmentally importantdehalogenation reactions. These microbial enzymes representobjects of interest for protein engineering studies, attemptingto improve their catalytic efficiency or broaden their substratespecificity towards environmental pollutants. This paper presentsthe results of a comparative study of haloalkane dehalogenasesoriginating from different organisms. Protein sequences andthe models of tertiary structures of haloalkane dehalogenaseswere compared to investigate the protein fold, reaction mechanismand substrate specificity of these enzymes. Haloalkane dehalogenasescontain the structural motifs of /ß-hydrolases and epoxidaseswithin their sequences. They contain a catalytic triad withtwo different topological arrangements. The presence of a structurallyconserved oxyanion hole suggests the two-step reaction mechanismpreviously described for haloalkane dehalogenase from Xanthobacterautotrophicus GJ10. The differences in substrate specificityof haloalkane dehalogenases originating from different speciesmight be related to the size and geometry of an active siteand its entrance and the efficiency of the transition stateand halide ion stabilization by active site residues. Structurallyconserved motifs identified within the sequences can be usedfor the design of specific primers for the experimental screeningof haloalkane dehalogenases. Those amino acids which were predictedto be functionally important represent possible targets forfuture site-directed mutagenesis experiments.     

Absolute interferometry with a 670-nm external cavity diode laser

In the past few years there has been much interest in use of tunable diode lasers for absolute interferometry. Here we report on use of an external cavity diode laser operating in the visible (lambda ~ 670 nm) for absolute distance measurements. Under laboratory conditions we achieve better than 1-mum standard uncertainty in distance measurements over a range of 5 m, but significantly larger uncertainties will probably be more typical of shop-floor measurements where conditions are far from ideal. We analyze the primary sources of uncertainty limiting the performance of wavelength-sweeping methods for absolute interferometry, and we discuss how errors can be minimized. Many errors are greatly magnified when the wavelength sweeping technique is used; sources of error that are normally relevant only at the nanometer level when standard interferometric techniques are used may be significant here for measurements at the micrometer level.     

Reactant partitioning in free-radical heterophase polymerization: The case of inverse microemulsion polymerization of acrylamide

Conversion curves have been determined at 60°C for the polymerization of acrylamide in percolating inverse microemulsions. Ammonium peroxo-disulphate (APS) and dibenzoyl peroxide (DBP) were used as initiators of free-radical polymerization in the presence or absence of potassium nitrosodisulphonate (Fremy's salt, FS). The percolation decreases the rate of polymerization of acrylamide initiated by APS. The polymerization is inhibited by FS. After an inhibition period, retardation of acrylamide polymerization is more pronounced in non-percolating microemulsions. No inhibition periods were observed for DBP-initiated polymerization of acrylamide. The percolation shortens the time interval of the ‘slow’ polymerization of acrylamide, but the rates of rapid acrylamide polymerization above 10% conversion are the same for percolating and for non-percolating inverse microemulsions. The polymer particle diameter is a function of acrylamide/water weight ratio and of [water]/[AOT] (AOT: bis(2-ethylhexyl)-sulphosuccinate sodium salt) molar ratio. No effect of the initiator's nature either in the presence or in the absence of FS was found. The results are interpreted on the basis of initiator and/or nitroxide radical partitioning between oil and water phases of the inverse microemulsion, and are discussed with respect to the mechanism of acrylamide polymerization and polymer particle formation proposed for non-percolating inverse microemulsions.     

Poly(methyl methacrylate) and polyacrylonitrile dispersions stabilized by gelatin

Methyl methacrylate was polymerized in an aqueous medium in the presence of gelatin using potassium persulfate as initiator. The dispersion mode of polymerization, when the monomer is completely miscible with water, was investigated and compared with an emulsion process, which proceeds at higher monomer concentration. Spherical and relatively uniform polymer particles were formed. Macroscopic precipitation of polymer is prevented by combination of the steric stabilization by grafted gelatin and of repulsive electrostatic interactions from the initiator residues attached to the particle surface. Static and dynamic light scattering have been used to determine the molar mass (molar mass of the whole dispersion particle, M_wD ～ 10⁸-10⁹ g mol^?1) and hydrodynamic radius (R_hD ～ 50-120 nm) of the particles. The number of particles per unit volume does not depend on overall monomer concentration, and it is higher, and therefore the particle size is smaller, than that observed for the soapless emulsion polymerization. The addition of gelatin may be thus used to modify the particle size. Acrylonitrile dispersions were prepared under similar conditions. Unlike methyl methacrylate, this monomer does not swell the polymer particles. While poly(methyl methacrylate) particles are spherical and relatively uniform, the polyacrylonitrile dispersions consist of polydisperse aggregates of tiny polymer particles.     

Influence of oxygen partial pressure and substrate temperature during vapour deposition on the structural properties of CdSe films

CdSe films prepared in vacuum by sublimation from the compound at oxygen partial pressures in the residual atmosphere from 2.8 × 10^?5 to 3.2 × 10^?4 Torr and at substrate temperatures of 295 and 523 K were subjected to X-ray structural analysis. The results obtained are analysed and discussed in terms of some structures different from those of CdSe, e.g. CdSeO₃ and CdSeO₃.SeO₂.