Preparation of bismuth nanowire encased in quartz template for Hall measurements using focused ion beam processing

ABSTRACT: Forming electrodes on opposite sides of an individual bismuth nanowire was attempted to prepare for Hall measurements. Although a 1-mm-long bismuth nanowire which is completely covered with a quartz template has been successfully fabricated to prevent oxidation, it is very difficult to attach Hall electrodes on the opposite sides of the nanowire due to the quartz covering. One side of the cylindrical quartz template was removed by polishing without exposure of the nanowire to the atmosphere; the thickness between the polished template surface and the nanowire was estimated to be several micrometers. Focused ion beam processing was successfully employed to expose both surfaces of the nanowire under high vacuum by removing part of the quartz template. A carbon thin film was then deposited in situ on the wire surface to fabricate an electrical contact on the bismuth nanowire sample. Furthermore, the energy dispersive X-ray analysis was performed to the area processed by focused ion beam, and the bismuth component of the nanowire was successfully detected. It was confirmed that the focused ion beam processing was applicable to attach electrodes to bismuth nanowire for Hall measurement.     

Nanostructured poly(3-hexylthiophene-2,5-diyl) films with tunable dimensions through self-assembly with polystyrene

Poly(3-hexylthiophene-2,5-diyl) is among the most widely used conjugated polymers for opto-electronic applications. To enhance its properties, researchers have attempted to nanostructure this polymer using various processes including breath figure arrays, nanolithography and elaborated organic synthesis. We here demonstrate a simple process to nanostructure the conjugated polymer using self-assembly with polystyrene and selective removal of one of the phases. The influence of the molecular weight of each polymer on the thin film morphology was systematically studied by atomic force microscopy. Using this approach, we observe two types of nanostructure, namely, nanoporous and nanoisland structures, of which the dimensions can be tuned by modifying the molecular weight of each polymer in the blend. This simple process introduces a cost-effective alternative to produce thin films of conjugated polymer with average nano-features from 100 nm up to 500 nm which could be used in a wide range of applications.     

Selective oxidation of ethane and propane over sulfated zirconia‐supported nickel oxide catalysts

The oxidative dehydrogenations of ethane and propane were investigated over a series of zirconia and nickel‐oxide supported on zirconia catalysts. It was found that zirconia, sulfated zirconia as well as NiO‐based zirconia catalysts showed high catalytic activities for oxidative dehydrogenation of ethane and propane. However, conversion and selectivity differed depending on the nature of the catalysts. Zirconia, sulfated zirconia (SZ) and their supported NiO catalysts showed high ethane conversions but lesser selectivities to olefins while NiO/Li₂ZrO₃ exhibited high selectivities to ethylene and propylene. Addition of an LiCl promoter in the NiO/SZ catalyst increased the catalytic activity and olefin selectivity, thus resulting in a higher olefin yield. In the oxidative dehydrogenations of ethane and propane NiO–LiCl/SZ exhibited 79% ethylene selectivity at 93% ethane conversion at 650 °C and 52% selectivity to propylene at 20% propane conversion at 600 °C, respectively. Characterization showed that the physico‐chemical properties of the catalysts determine the catalytic activity and selectivity. © 2001 Society of Chemical Industry     

Hydrogen production from methane steam reforming: parametric and gradient based optimization of a Pd-based membrane reactor

In this work three mathematical models for methane steam reforming in membrane reactors were developed. The first one is a steady state, non isothermal, non isobaric and one dimensional model derived from material and energy balances and validated using experimental data from the literature. It is referred as full model. The influence of two different intrinsic kinetics available, as well as, the influence of five important parameters on methane conversion (X_CH4_{\mathrm{CH}_{4}}) and hydrogen recovery (Y_H2_{\mathrm{H}_{2}}) were parametrically evaluated through simulations. The second model, referred as meta-model, was obtained though the response surface technique. This meta-model was included into a constrained optimization problem solved using NPSOL. The third model, referred as a simplified model, takes into account only mass balances from the full model. Using this model, a gradient based method (DIRCOL) was used to perform the optimization of the sum of methane conversion and hydrogen recovery. High methane conversions and hydrogen recoveries were reached through these methodologies.     

Preliminary spectrum shifter design for intermediate energy nuclear data benchmark experiments with DT neutrons

Integral benchmark experiments with DT neutrons are not always sufficient for nuclear data benchmarking in the MeV region, below 10 MeV. A neutron spectrum shifter, which will be placed between a sample and a DT neutron source, is effective to moderate DT neutrons incident to the sample. In order to estimate effects of the spectrum shifter, the ratio of the contribution of 14 MeV neutrons in the leakage neutron and gamma-ray spectra was calculated with MCNP-4C for an experimental configuration at FNS of JAEA, Japan. The calculations were carried out for a Li₂TiO₃ sample with a Be, D₂O, or ⁷LiD spectrum shifter. It was found out that the Be shifter was superior to others and the Be shifter was effective to decrease the contribution of 14 MeV neutrons especially for secondary gamma-ray spectrum measurements.     

Antifungal activity of the fermentation product of herbs by lactic acid bacteria against tinea

The fermentation product of herbs by lactic acid bacteria (FHL), in which Enterococcus faecalis TH10 predominated, was assayed for antifungal activity against tinea. The antifungal activity of FHL was as high as that of a synthetic fungicide. Autoclaving FHL did not reduce its antifungal activity, whereas neutralizing it did. The results suggested that nonproteinaceous compounds or organic acids in FHL could inhibit the growth of the dermatophyte tinea under low-pH conditions, and that malonic acid and acetic acid could have especially high antifungal activity against tinea.     

Impulse breakdown superposed on ac voltage in XLPE cable insulation

This paper discusses tree inception and breakdown voltage characteristics of XLPE cable insulation subjected to impulse voltages superimposed on ac voltage. The tree initiation tests were performed on laboratory-molded specimens equipped with needle electrodes, whereas the breakdown tests were conducted on a full-sized cable. The impulse tree initiation stress was found to be dependent on the magnitude of the pre-applied ac stress and the relative polarities of the impulse and the ac peak at the instant of their superposition. Although the impulse polarity has an effect on the tree inception, the general behavior is that the tree inception stress always decreases with an increase of the pre-applied ac stress. This phenomenon is discussed in terms of the space charge effect and the influence of the impulse voltage application itself. The impulse strength of a full-sized cable insulation was found to be independent of the pre-applied ac stress as long as that stress did not exceed the operating stress of a 500 kV cable insulation. However, subjecting cable insulation to higher ac stresses before impulse application caused a reduction of its breakdown strength as compared with the insulation without ac prestressing     

Trehalose embedding technique for high-resolution electron crystallography: application to structural study on bacteriorhodopsin

Trehalose was compared with glucose in its use as an embedding medium for the preparation of two-dimensional crystals for electron crystallographic structure analysis. Purple membranes (two-dimensional crystals of bacteriorhodopsin) embedded in either sugar were studied in a 'partially hydrated' state as well as after 'drying' of the specimen. Diffraction patterns of the four conditions, all showing spots to a resolution better than 3.0 A, were analysed and merged. In the case of glucose embedded specimens, the merging R-factor obtained from the diffraction patterns of dried specimens was significantly better than the one obtained from partially hydrated specimens. In the case of trehalose embedding, the merging R-factor for partially hydrated specimens was significantly better than the dried one. The trehalose embedded, partially hydrated specimens gave the best merging R-factor in all four cases.