北京地区潮土对土霉素的吸附特性研究

北京近1/4区域土壤属于潮土,潮土对四环素类抗生素的吸附特性还鲜有报道。采用OECD Guideline 106的方法,研究土霉素在北京地区潮土上的吸附特性。结果表明,土霉素在潮土中的吸附动力学过程符合Elovich方程,土霉素初始浓度会影响吸附速率,2 mg/L时最大,10 mg/L时最小。吸附百分比随着初始浓度的升高,先增大后减小。温度和平均吸附速率呈负相关。实验浓度下,吸附等温线符合线性等温方程和Freundlich方程,吸附是自发的吸热反应。潮土对土霉素的吸附量和粉粒及黏粒含量之和呈正相关。土霉素在潮土中的吸附受初始浓度、温度、土壤性质等因素的影响,深入了解其作用机理,有助于防治土霉素污染,保护土壤安全。     

泥沙影响流速分布规律的试验研究

挟沙水流中泥沙颗粒的存在将影响水流的紊动结构,并进一步影响水流流速分布。采用超声流速仪MicroADV测量挟沙水流的时均流速沿垂线分布,分析了在不同水力条件、不同泥沙条件(包括泥沙浓度及颗粒粒径)下泥沙与水流相互作用对流速沿垂线分布的影响,在此基础上,考虑到现有流速分布公式在实际河道水流流速沿垂线分布中的应用,提出新的指数型流速分布公式形式;并根据实验资料,初步检验了该公式的精度,同时分析了指数型流速公式中系数k和指数m随泥沙浓度s、粒径d以及水力条件的变化规律。结果表明:系数k随泥沙浓度的增加而增大,同时水力条件以及泥沙颗粒粒径同样也影响着k的变化;而指数m随粒径d的增大而减小,随泥沙浓度s的增加而增大。     

电容去离子化去除地下水中镉的影响因素

以高比表面积活性炭作为吸附剂制备电容电极,研究电容去离子化（CDI）对地下水中镉的吸附性能。分别探讨了镉初始质量浓度、体系供电电压、地下水中常见阳离子种类对CDI去除镉的影响。结果表明,CDI吸附镉符合准二级吸附动力学、满足Langmuir等温吸附方程,CDI对镉的吸附为单分子层吸附。吸附量随镉初始质量浓度的升高而增加;在低质量浓度时,较高的供电电压会提高初始阶段的吸附速率,但对电极的最终吸附量无显著影响;地下水中主要阳离子的存在增加了体系的电导率,从而促进了CDI对镉的吸附,提高了镉的吸附速率和去除率。     

渗流作用下的江河岸坡冲刷变形分析

岸坡地形随河流上游来水来沙、河势变化等因素而不断变化,直接影响岸坡稳定性。江河水流、岸坡渗流均对岸坡水下地形变化有很大的影响。通过分析泥沙受力条件和冲刷特性,应用在室内水槽进行的不同泥沙粒径在多种水流条件下的冲刷率试验研究成果,在岸坡泥沙受力分析基础上推导了崩岸冲刷率公式,并以算例具体说明江河水流和岸坡渗流对其冲刷变形过程的影响。     

不同粒径泥沙共存吸附动力学模式研究

天然水体中泥沙组成具有非恒定性和非均匀性,而不同粒径泥沙的吸附能力差异很大.因此.讨论天然水体中泥沙对重金属污染物的自净能力,必须研究不同粒径泥沙共存(即非均匀沙)的吸附模式.通过系统室内静态试验,研究了不同粒径泥沙共存吸附的吸附动力学模式.它表明,不同粒径泥沙共存吸附体系各粒径之间不存在竞争和干扰,共存体系单位重量泥沙的吸附量等于各粒径泥沙单独存在,在相同条件下单位重量泥沙的吸附量乘以其在共存体系中所占份额的和.这在一定程度上解决了天然河流水体泥沙吸附量的计算问题.     

坡缕石/氧化铝复合材料对磷的吸附动力学和热力学

以坡缕石粘土为原料,通过溶胶-凝胶法制备坡缕石/氧化铝复合材料,通过静态吸附实验研究了复合材料吸附水中磷的动力学特征、吸附平衡和热力学参数,探讨了吸附机理。结果表明,复合材料对磷有较好的吸附作用,吸附过程能较好地符合准二级动力学方程,吸附速率常数随初始浓度的增大而减小,随温度的升高有所增大;吸附平衡能较好地符合Langmuir方程和D-R方程,吸附过程吸热,ΔG为-25~-21 kJ/mol,是物理吸附和化学吸附并存的过程。     

斜发沸石对钾离子的吸附/解吸动力学研究

以KCl为钾源、新疆某地所产斜发沸石为吸附剂,研究斜发沸石对K+的动力吸附与解吸效果,并探讨吸附时间、K+初始浓度与吸附量的关系。用pH=5的HCl溶液和(Ca2++Mg2+)浓度/(mmol.L-1)为1.6,3.2,6.4,12.8,19.2,25.6的混合溶液对饱和吸附了K+的斜发沸石进行解吸,实验结果表明:沸石对K+的吸附在4min能达到最大吸附率的96%,30min内达到平衡。Langmuir吸附等温式能对吸附曲线进行很好的描述。单位质量沸石对K+的最大吸附量为44.53×10-3,以阳离子交换吸附为主。pH=5的HCl溶液对K+的解吸量最小,随解吸溶液中(Ca2++Mg2+)浓度增加,解吸滞后系数减小,解吸速率远小于吸附速率。解吸量的自然对数与解吸时间的自然对数呈现明显的线性关系,用指数方程对(Ca2++Mg2+)浓度为25.6mmol/L的解吸曲线进行拟合,R=0.998,拟合方程为qt=3.890t0.210。理论上将吸附的K+全部解吸出来需要74.4d。     

铵在中砂上的3种吸附形态研究

通过动力学和等温吸附实验,研究了不同初始氨氮浓度下水溶铵、交换铵和固定铵在中砂上的吸附规律。结果表明,吸附平衡时各种形态铵含量随初始氨氮浓度增加而增大。3种形态铵吸附行为符合准二级动力学方程。吸附速率常数K大小顺序为：固定铵〉交换铵〉水溶铵,初始速率：固定铵〈交换铵〈水溶铵。随着初始氨氮浓度的增加,水溶铵占总铵的比重由40%上升到65%,其吸附的主要限制步骤为颗粒间扩散。交换铵对总铵的贡献率维持在25%左右,吸附饱和后有所降低,初始氨氮浓度为交换铵吸附的主要限制步骤。固定铵达到饱和时,吸附量只有26.18 mg/kg,对总铵的贡献率由33%下降到9%。     

土壤矿物对金属离子的临界吸附量

本文从矿物表面羟基与溶液中金属离子反应的化学平衡方程出发,得到金属离子在矿物表面单基配位和双基配位吸附的覆盖度计算公式,并据此探讨了覆盖度的影响因素和变化规律,指出覆盖度随pH变化曲线拐点的实际意义。假设土壤和地表水达到平衡,参比水质标准,提出了矿物吸附金属离子的临界覆盖度公式,并初步探讨了石英吸附Cd2 的临界覆盖度-pH曲线,进而推导出土壤矿物对金属离子的临界吸附量公式。     

泥沙颗粒生长生物膜后起动的实验研究——Ⅱ.起动流速计算

泥沙颗粒生长生物膜后,起动流速发生了较大变化.根据生长生物膜后的泥沙起动流速实验数据,考虑天然水体中,生物膜填充于颗粒与颗粒之间形成除水以外新的介质,将生物膜的作用模化为生物膜作用产生的粘连力,再考虑生物膜随时间变化的特性以及基底物理特性的影响等因素,结合泥沙颗粒之间由于薄膜水产生的黏结力、重力等,研究了颗粒在滑动和滚...     

Adsorption of Ammonium and Heavy Metal Ions on Industrial Vermiculite from the Yuli Mine in Xinjiang, China

The present work discusses the mineralogy, saturated adsorption of ammonium and adsorption of heavy metal ions （Cu^2＋, Pb^2＋ and Zn^2＋） on industrial vermiculite samples from the Yuli Mine in Xinjiang Autonomous Region. The saturated adsorption capacity of ammonium and the affection factors of adsorption of Cu^2＋, Pb^2＋ and Zn^2＋ are discussed on the basis of the mineralogical characteristics of the industrial vermiculite samples. The saturated adsorption capacities of ammonium are between 56.02 and 98.42 mmol/100g. The time of adsorption equilibrium is about 30-60 min, and the pH values and concentration of the ion solution significantly affect the adsorption capacities of the heavy metal ions. The adsorption capabilities of the heavy metal ions on industrial vermiculite are almost the same in the low ion concentration solutions, characterized by a sequence of Zn^2＋〉Pb^2＋〉Cu^2＋ for adsorption capacity in solutions with relatively high ion concentration. The results have practical significance for the application of the industrial vermiculite to treating wastewater containing ammonium or heavy metal ions.     

Sorption of heavy metals from aqueous solution by dehydrated powders of aquatic plants

Ruppia maritima and Echinodorus amazonicus were prepared in a dehydrated powder form. The characteristics and mechanisms of adsorption of heavy metals were studied under various pH values, reaction times, and heavy metal ion concentrations. The results showed that under different pH and reaction time conditions, heavy metal adsorption was lead > cadmium > zinc > copper. The adsorption of lead increased linearly with the lead concentration. For cadmium, zinc and copper, the adsorption was saturated when metal ion concentration exceeded 200 mg/L. When a Freundlich model was applied, R ² values for the heavy metal adsorption by the aquatic plants mostly exceeded 0.9. The adsorption of heavy metal ions by these two aquatic plant powders was better explained by the Lagergren second-order equation than the first-order equation. From the Fourier Transform Infrared spectra, there was an adsorption peak at 2,115 cm^?1 for R. maritima. The peak shape did not change with metal affiliation except there was a shift of peak wavelength before adsorption. The results indicate that the mechanism of heavy metal adsorption by the two species is not simply on the mono-molecular layer level, and that intra-particulate dispersal is the dominant process. Heavy metal pollution does not affect the basic chemical components, and major substances involved in heavy metal adsorption including carbohydrates, cell wall pectin, and protein functional groups.     

ZH型重金属螯合纤维对水溶液中Sr2+的吸附行为

研究了ZH型重金属螯合纤维对水溶液中Sr~(2+)的吸附行为,考察了pH值、纤维加入量、Sr~(2+)初始浓度、作用时间等对吸附行为的影响,并采用SEM、EDS和FTIR等现代分析测试手段探讨了ZH型重金属螯合纤维对Sr~(2+)的吸附机制。结果表明,在pH值为7.0、纤维加入量为2.0 g/L、Sr~(2+)初始质量浓度为50 mg/L的条件下,纤维对Sr~(2+)的吸附在4 h左右基本达到平衡。实验条件下ZH型重金属螯合纤维对Sr~(2+)的最大吸附量可达26.22 mg/g。等温吸附拟合结果表明,ZH型重金属螯合纤维对Sr~(2+)的吸附可能是以单分子层为主的单分子层和多分子层吸附共同作用的结果。纤维对Sr~(2+)的动力学吸附过程符合准二级动力学模型。红外光谱分析表明Sr~(2+)与纤维上—NH_2和—COOH等基团进行配位络合从而吸附在纤维表面,—CH_2—和C=CH_2等基团参与此吸附过程。能谱分析表明Sr~(2+)与纤维上Na~+和Ca~(2+)还存在着离子交换作用。     

柱撑蛭石吸附去除废水中重金属离子的实验研究

分别利用有机柱化剂十二烷基磺酸钠(SDS)和无机柱化剂聚羟基铝(HA)对蛭石进行柱撑制得十二烷基磺酸钠柱撑蛭石(SDS-V erm icu lite)和聚羟基铝柱撑蛭石(HA-V erm icu lite),并通过XRD、红外光谱、ZETA电位等表征手段对柱撑蛭石进行表征,同时针对柱撑蛭石对Cu2 ,Cd2 ,C r3 3种重金属离子的吸附进行研究,结果表明:吸附去除率受反应时间、重金属离子的初始浓度、pH值等因素的影响,经柱撑后的蛭石对重金属离子吸附的吸附性能比蛭石原矿要强。柱撑蛭石吸附3种重金属离子的动力学吸附过程可用E lov icb方程和双常数方程进行较好的拟合。     

Application of dried plant biomass as novel low-cost adsorbent for removal of cadmium from aqueous solution

Heavy metals are a threat to human health and ecosystem. These days, great deal of attention is being given to green technologies for purification of water contaminated with heavy metal ions. Biosorption is one among such emerging technologies, which utilizes naturally occurring waste materials to sequester heavy metals from wastewater. Cadmium has hazardous impact on living beings; therefore, its removal through green and economical process is an important task. The aim of the present study was to utilize the locally available Portulaca oleracea plant biomass as an adsorbent for cadmium removal from aqueous solution. The biomass was obtained after drying and grinding the portulaca leaves and stem. No chemical treatment was done on the adsorbent so that it remained green in a true sense. Batch experiments were performed at room temperature. The critical parameters studied were effects of pH, contact time, initial metal ion concentration and adsorbent dose on the adsorption of cadmium. The maximum adsorption was found to be 72 %. The kinetic data were found to best fit the pseudo-second-order equation. High adsorption rates were obtained in the initial 45 min, and adsorption equilibrium was then gradually achieved in about 100 min. Adsorption increased with increase in pH for a range 2 and 6. The equilibrium adsorption results closely followed both the Langmuir and Freundlich isotherms. The values of constants were calculated from isotherms. Results indicated that portulaca plant biomass could be developed as a potential material to be used in green water treatment devices for removal of metal ions.     

Marine scavenging: Trace metal adsorption by interfacial sediment from MANOP Site H

The adsorption of thirteen trace metals from seawater was studied on interfacial sediment from MANOP site H. The adsorption data indicate a long (~20 day) equilibration time for most metals, an increase in adsorption with an increase in pH and particle concentration, a dependence of adsorption on total metal concentration at high adsorption densities, and a lack of correlation between metal binding ability and metal hydrolysis in solution.Apparent equilibrium binding constants normalized to the total number of available sites on the solid were determined for metal binding with the interfacial sediment. The binding constants indicate that the affinity sequence for metal interactions with the interfacial sediment is: Pb > Fe > Sn ? Co≈ Mn > Cu > Be > Sc ? Zn > Ni > Cd ? Ba > Cs at pH 7.82 in seawater.A comparison of the binding constants for suspended particles, interfacial sediment, and surface sediment indicate that the composition of particles influences the binding ability of the particles. Biogenic particles tend to bind most metals more strongly than lithogenic or authigenic particles.Based on limited data, there is a strong positive correlation between the measured binding constants and the observed partitioning of metals between sediment and seawater.     

Aqueous heavy metals removal by adsorption on β-diketone-functionalized styrene–divinylbenzene copolymeric resin

An investigation was undertaken regarding the adsorption of different heavy metal ions from aqueous solutions using ??-diketone-functionalized styrene divinylbenzene resin under different experimental conditions such as initial concentration of metal ions, contact time, pH, and chelating capacity. The functionalization of resin was carried out by the condensation reaction of sodium salt of ??-diketones (pentane-1,3-dione) and chloromethylated styrene?Cdivinylbenzene resin in dichloromethane. Functionalized resin beads were characterized by Fourier transform infrared spectroscopy. The batch method was employed using different metal ions solution from 5 to 15?mg/L at different contact times. The adsorption kinetics was tested for the pseudo-first order, pseudo-second order reaction at different experimental conditions. The rate constant of adsorption kinetic models were also calculated and good correlation coefficient (R ²?>?0.9941) was obtained for pseudo-second order kinetic model. The maximum adsorption value obtain for lead (0.725728?mg/g), chromium (0.9199?mg/g), nickel (0.4974?mg/g), cobalt (0.6196?mg/g) and cadmium (0.6519?mg/g) at equilibrium condition, which shows that ??-diketone-functionalized styrene divinylbenzene resin is an effective adsorbent for toxic metal ions.     

Competitive heavy metals adsorption on natural bed sediments of Jajrood River,Iran

The presence of heavy metal concentrations was examined in natural sediments from four sites along the Jajrood river in northeast of Tehran, the capital of Iran. Besides determination of elemental concentrations (Pb, Cu, Zn, Cd, Ni and Cr), X-ray fluorescence and X-ray diffraction tests were carried out to determine other chemical components in these adsorbents. Also the ability of sediments to adsorb these heavy metal ions from aqueous solutions was investigated. Results show that the extent of adsorption increases with increase in adsorbent concentration. The amount of adsorbed Pb, Cu and Zn in sediments was much greater than that of the other metals, and Cr was adsorbed much less than others. The adsorbabilities of sediments to heavy metals increased in the order of Pb > Cu > Zn > Cd > Ni > Cr. Based on the adsorption data, equilibrium isotherms were determined at selected areas to characterize the adsorption process. The adsorption data followed Freundlich and Langmuir isotherms in most cases. Correlation and cluster analysis was performed on heavy metals adsorption and sediment components at each site to evaluate main adsorbing compounds in sediments for each metal. Results demonstrated that heavy metals sorption is mostly related to load of organic matter in the Jajrood river sediments.     

Adsorption characteristics of phenol and heavy metals on biochar from <Emphasis Type="Italic">Hizikia fusiformis</Emphasis>

The objective of the present study is to evaluate the absorption efficacy of H. fusiformis biochar (HFB) for the removal of phenol and heavy metals from single and mixed solute systems of these species under different experimental conditions. The effects of contact time, pH change, initial phenol concentration, and heavy metal concentration on the adsorption capacity of HFB were investigated. The kinetics and equilibrium models of sorption of the components of the single and mixed solute systems on HFB were also studied. The experimental data were fitted to kinetic and equilibrium models. The batch experiments revealed that 360 min of contact time was sufficient to achieve equilibrium for the adsorption of both phenol and heavy metals. The adsorption of phenol and nickel by HFB followed the pseudo-second-order kinetic model, which was quite adequate for describing the adsorption mechanism. The equilibrium data for the adsorption of phenol and heavy metals fit well to the Langmuir model with regression coefficients of R ² > 0.819. The maximum Langmuir adsorption capacities were 10.39, 12.13, 22.25, 2.24, 2.89, and 22.03 mg/g for phenol, Ni²⁺, Zn²⁺, Cu²⁺, Pb²⁺, and Cd²⁺, respectively. Moreover, HFB exhibited optimal sorption under slightly acidic conditions at pH 6. The HFB used in the present study exhibited higher adsorption capacity for the removal of phenol and heavy metals from aqueous solutions compared to documented sorbents. These results demonstrate that HFB is potentially useful for alleviating the harmful effects of phenol and heavy metal in wastewater treatment systems.