波浪周期对防波堤护面块体稳定性影响的试验分析

波浪对斜坡堤护面结构的冲刷破坏作用受诸多因素的影响,如波浪要素、水深条件、坡面角度、护面块体型式等。在进行某项有关斜坡堤护面块体的课题研究中发现,当防波堤断面结构确定后,护面人工块体的稳定性主要取决于波高及波周期的变化。在进行这方面内容设计计算中,通常波高的取值都能给予足够的重视,但波周期对护面块体稳定性的影响容易被忽视。本研究通过物理模型试验,针对波浪周期对斜坡堤护面块体稳定性的影响进行了总结分析,为防波堤设计提供参考。     

堆石防波堤不规则波浪反射系数试验研究

结合物理模型试验,分析斜坡坡度、波陡、相对水深、护面类型和破波参数等因素对堆石防波堤不规则波浪反射系数的影响规律。将常用的Van der Meer公式,Seelig公式,Postma公式和Davison公式计算值和实测值进行比较,并结合试验数据,基于有效波高和平均周期定义的Iribarren数,得出堆石防波堤不规则波浪反射系数经验公式。结果表明,该公式能较好地计算不规则波作用下块石和扭王块体护面堆石防波堤波浪反射系数。     

深水斜坡式防波堤人工垫层块体稳定性及反射系数研究

船舶大型化的趋势导致港口设施向深水发展。而对于深水防波堤,在较大设计波浪作用下,护面块体和垫层块石的重量往往超出现行技术规范的要求,针对大型天然块石垫层选料和施工困难,大量的开山选石损害自然环境等问题,本文总结了国内外人工块体的研究成果,阐明了人工块体垫层代替大型块石垫层的可行性,遴选了3种类型人工块体作为垫层,进行护面块体稳定性试验,经对比分析得出扭王字护面下带槽方块垫层的新结构,并确定其重量比值关系对护面稳定性的影响;对比传统垫层块石,给出遴选人工块体垫层的K_D值、堤前反射系数经验公式及波浪爬高糙渗系数推荐值。通过物理模型试验证明了深水斜坡防波堤通过采用人工垫层块体代替大型天然垫层块石的方法是可行的,为港口工程技术规范的修订提供了参考。     

斜坡堤堤头护面块体的稳定性——石臼港引堤模型实验研究

本文是石臼港模型实验研究成果的一部分。通过实验提出了计算斜坡堤堤头护面块体稳定重量的初步方法。文中结论得到了原体观测的验证。     

斜坡堤护面块体安放过程及稳定性数值模拟

利用基于光滑粒子流体动力学(SPH)数值方法的开源软件DualSPHysics进行数值试验,模拟斜坡式防波堤上扭王字护面块体的安放过程,研究护面块体的稳定性。首先以DualSPHysics为平台开发了护面块体的安放功能模块,并对护面块体的安放效果进行评价,实现了按指定安放密度进行块体安放。块体安放完成后,在数值波浪水槽中研究护面块体在规则波作用下的运动及受力响应,并分析护面块体失稳的典型形式和失稳标准,通过系统化的参数分析,探讨波浪要素及块体安放等因素对块体稳定性的影响。结果表明,扭王字块体稳定性系数的取值范围为21.64~26.20,是规范推荐值的1.5倍左右。块体鼻轴方向的相对位置主要影响单个块体的上举脱出失稳,鼻轴方向在坡面上赤平投影图越分散,护面块体层整体上越稳定。坡面坡度变缓时,护面块体层整体下滑趋势减弱,但更易发生上举脱出失稳;单个块体缺失会加大周围块体的上举失稳概率。     

扭王字块体护面斜坡堤越浪量试验研究

针对现行规范中缺少扭王字块体护面斜坡堤越浪量的计算方法,考虑波陡、相对水深、相对堤顶超高、相对坡肩宽度、相对胸墙高度和相对块体尺寸等影响因素,通过波浪水槽物模试验,运用多元回归方法,给出了扭王字块体斜坡堤越浪量中护面结构影响系数和平均越浪量的计算公式。与试验值和其它计算公式进行了验证对比,结果基本吻合,具有一致性的规律。研究成果丰富了规范内容,对斜坡堤工程设计具有重要参考意义。     

防波堤断面结构型式及护面块体稳定性模型试验研究——2008北京奥运会青岛帆船比赛基地水工模型试验

为确保2008北京奥运会青岛帆船比赛基地内工程的水工建筑物安全可靠，对给定的2种防波堤断面结构型式及护面块体稳定性进行物理模型试验。准确掌握在极端高水位、设计高水位、设计低水位和极端低水位时．SW向、25a和50a一遇波浪作用下，试验断面所承受的波浪作用力，及SE向50a一遇波浪作用下块体的稳定重量。并绘制各工况1％峰值波压力分布图，得出断面波压力的分布规律。对断面结构和护面块体稳定性进行分析。     

宽肩台式抛石防波堤稳定性的试验研究

宽肩台式无人工护面块体的抛石防波堤是一种新型结构的斜坡堤,它是靠在波浪长期作用下最终形成的动力平衡断面来防浪的。大连北良粮食中转港系银行贷款建设的项目,该港的防波堤采用了宽肩台式结构,这在我国尚属首例。本文为该港宽肩台式防波堤设计方案稳定性的试验研究成果。     

多向不规则波作用下斜坡式建筑物护面块体的稳定性

试验研究了扭工字块体、钩连块体、四脚空心方块和块石等四种护面块体在五种波向角(0°,15°,30°,45°和60°)的斜向波和多向不规则波作用下的稳定性,给出了四种护面块体稳定重量的实用计算方法.     

斜坡堤天然块石护脚的稳定性计算

试验研究表明 ,不规则波对斜坡堤护脚棱体稳定性的威胁大于波高对应于Hs 的规则波 ,斜坡堤护面形式对护脚块石的稳定也有影响。Gerding公式虽然准确地描述了棱体在波浪作用下的稳定性规律 ,但由于护面糙率、透水率等因素的影响在工程上应用仍需进一步修正。文章指出在中低水位 ,Gerding公式计算的护脚棱体稳定重量有可能偏小 ,并给出了不同类型护面下护脚棱体稳定计算的修正系数     

Experimental Research of Hexagon Multihole Armour Block on Breakwater

This paper introduces a new kind of armour block - hexagon multihole block on sloping breakwater. It has great characteristics such as good interlocking, strong resistance against waves and saving concrete. Through the hydraulic model test, the mechanism of stability of the block has been proved and the relations between stability and wave height, wave period, water depth, slope, laying method, porosity and cushion have been found. The effect of weight on steadiness have also been discovered. Finally, the method of design and some formulas are given.     

Experiment for Determination of Dry-Laid Stone Armour Layer Thickness of Rubble Mound Breakwaters

Through hydraulic model experiment and site investigation, this paper has derived a calculation formula of dry-laid stone armour layer thickness of rubble mound breakwaters for fishery harbours. The influences of the friction force between stone blocks and the variations of wave length or period and water depth are considered in the formula. The calculated results of several existing structures are in good agreement with field data. This formula is more practical than those ever published both at home and abroad, and has been adoptted by the technical standards of aquatic projects published by the Ministry of Agriculture of China. It is applicable for the calculation of dry-laid stone armour layer of breakwater for small- or medium-size harbours.     

波浪作用下方块石护面稳定性研究

护面是海堤和护岸的重要结构,直接抵御波浪作用,可采用人工块体、块石等,种类繁多。采用紧密排列方块石作为护面结构是一种景观性较好的型式,依据方块石厚度不同能抵御不同大小的波浪作用。干砌条石及干砌块石护面曾有一些规范给出过计算方法,但现行规范没有相关内容可供设计参考,已有计算方法的理论分析还存在不足。当波浪与斜坡堤相互作用时,方块石护面出现位移或脱落可能发生在波浪回落最低阶段、波浪破碎打击阶段及破后爬高水流作用阶段,通过研究得到了不同阶段波浪对方块石护面作用力的计算方法。在波浪回落最低阶段,考虑了护面及其下方垫层渗透性影响,通过理论分析建立了低渗透护面浮托压强计算模型,采用物模试验将计算结果与试验测量值进行了对比分析,结果表明总体趋势符合,量值接近;在波浪破碎冲击阶段,基于射流冲击作用原理,提出了波浪在斜坡面破碎冲击压强计算方法,通过试验分析了波浪破碎水深波高比与破波相似参数的关系,利用浅水波理论计算了波浪破碎冲击水流流速;在爬高水流作用阶段,提出了水流引起的方块石护面垂直浮托力及水平拖曳力的计算方法,通过试验结果拟合了浮托力系数和拖曳力系数,验证了水流作用下护面的受力特征。最后,针对方块...     

Core made of geotextile sand containers for rubble mound breakwaters and seawalls: Effect on armour stability and hydraulic performance

A systematic armour stability and the hydraulic performance, including wave reflection, wave transmission, experimental study in the twin-wave flumes of Leichtweiss-Institute (LWI) is performed on a geocore breakwater and a conventional rubble mound breakwater in order to comparatively determine the wave run-up and wave overtopping. The geocore breakwater consists of a core made of sand-filled geotextile containers (GSC) covered by an armour made of rock. The geocore is more than an order of magnitude less permeable than the quarry run core of a conventional breakwater. As expected, the core permeability substantially affects the armour stability on the seaside slope, the wave transmission and the wave overtopping performance. Surprisingly, however, wave reflection and hydraulic stability of the rear slope are less affected. Formulae for the armour stability and hydraulic performance of the geocore breakwater are proposed, including wave reflection, transmission, run-up and overtopping.     

Experimental analysis of breakwater stability with antifer concrete block

Armor is a pavement made of erosion-resistant materials like a stone or concrete that is constructed to protect breakwater, coasts, and other coastal line features against erosion. These armors are a kind of protective layer made of stone or concrete, used in breakwater constructions or coastal lines, arrayed with specific regular or irregular pattern on the breakwater or the coast. The antifer concrete blocks have almost cubic form, often changed into frustum by adding inclined plates to their sides. One of the most important advantages of these armors is their diversified regular and irregular placement patterns. In this study, using the physical modeling and different tests, the stability level of antifer concrete blocks was evaluated considering the decrease of the armor weight. Results of this study show that by a 10% decrease in the block weight, the failure graph slope is increased and the damage is intensified.     

On front slope stability of berm breakwaters

The short communication presents application of the conventional Van der Meer stability formula for low-crested breakwaters for the prediction of front slope erosion of statically stable berm breakwaters with relatively high berms. The method is verified (Burcharth, 2008) by comparison with the reshaping of a large Norwegian breakwater exposed to the North Sea waves. As a motivation for applying the Van der Meer formula a discussion of design parameters related to berm breakwater stability formulae is given. Comparisons of front erosion predicted by the use of the Van der Meer formula with model test results including tests presented in Sigurdarson and Van der Meer (2011) are discussed. A proposal is presented for performance of new model tests with the purpose of developing more accurate formulae for the prediction of front slope erosion as a function of front slope, relative berm height, relative berm width, method of armour stone placement, and hydraulic parameters. The formulae should cover the structure range from statically stable berm breakwaters to conventional double layer armoured breakwaters.     

On rubble-mound breakwaters of composite slope

The geometrical properties of the armor layer of rubble mound breakwaters were investigated by observations made on two cases. The first case is a laboratory-scaled model of natural rock, designed with a composite slope. The second is a breakwater in the sea, constructed with a uniform slope of tetrapods. In both cases the cross-section underwent changes, resulting in an apparently stable profile of composite slope. This implied that for stability the optimal armour layer should be of composite slope. The general nature of this profile was implied by the geometrical similarity between the two cases which were basically so different.