Distribution of clay-sized sediments in streambeds and influence of fine sediment clogging on hyporheic exchange

In this work, the deposition of clay-sized fine particles (d₅₀ = 0.006 mm) and its subsequent influence on the dune-induced hyporheic exchange are investigated. Fine sand (D₅₀ = 0.28 mm), coarse sand (D₅₀ = 1.7 mm), and gravel (D₅₀ = 5.5 mm) grains were used to form homogenous model streambeds; one control - no clay input, and two treatments - increasing clay inputs for each grain type. The results indicate that the clogging profiles of clay-sized sediments may not be predicted accurately using the previously proposed metric based on the relative sizes of infiltrating and substrate sediments. Further, the depositional patterns vary with the initial concentration of clay particles in the surface water. The assessment of clogging profiles in coarse-grained model streambeds also reveals a preferential infiltration of the clay particles in the hyporheic downwelling regions. The results from the dye tracer test suggest that the accumulation of clay particles altered the exchange characteristics in the treatment flumes. For each grain size, the treatment flumes exhibit lower hyporheic flux and higher median residence times compared to their respective control flumes. The dye penetration depths were lower in treatment flumes with fine and coarse sand compared to their respective control flumes. Interestingly, higher penetration depths were observed in treatment flumes with gravel compared to their respective control flume potentially due to the generation of preferential flow paths in the partially clogged gravel beds. The clogging altered the hyporheic fluxes and residence times in the coarse-grained model beds to a greater degree in comparison to the fine sand beds. Overall, our findings indicate that the properties of both fine and substrate sediments influence the clogging patterns in streambeds, and the subsequent influence of fine sediment clogging on hyporheic exchange and associated processes may vary across stream ecosystems.     

Effects of sand content on initial gravel motion in gravel‐bed rivers

When fine sediments are present in gravel streambeds (gravel‐framework beds), the gravel can be more easily removed from its original position, compared with gravel in a streambed without fine sediment but otherwise under the same hydraulic conditions. In this study, the effect of the presence of sand on the initiation of gravel motion in gravel riverbeds was investigated using flume experiments. The relationship between the critical Shields stress for gravel motion initiation and the fraction of sand in the bed was determined experimentally. The results can be summarized as follows. (1) When the fraction of sand in the bed is smaller than about 0.4, the critical Shields stress for the initiation of gravel motion decreases with increasing fraction of sand. The critical Shields stress increases, however, with increasing fraction of sand when it is larger than about 0.4. (2) The difference between the value of the critical Shields stress predicted by the Egiazaroff equation and the value obtained from the experimental data becomes maximum at about 0.4 of the fraction of sand. Here an empirical relation between the critical Shields stress and the fraction of sand is proposed so as to consider the effects of the ratio of the characteristic gravel size to the mean size of the bed material on the critical Shields stress. (3) Gravel in armored beds can be more easily mobilized by supplying sand as part of a sediment augmentation scheme. The sand fraction in the subsurface layer of the bed appears to reduce the friction angle of exposed particles. Sediment augmentation using sand has been recently demonstrated to be a viable alternative for mobilizing gravel for the restoration of gravel‐bed rivers downstream of dams. The quantitative evaluation obtained through the experiments reported here may be useful for the design of augmentation schemes. Copyright © 2017 John Wiley & Sons, Ltd.     

Suspended sediment dynamics at high and low storm flows in two small watersheds

A record spanning almost 20 years of suspended sediment and discharge measurements on two reaches of an agricultural watershed is used to assess the influence of in‐channel sediment supplies and bed composition on suspended sediment concentrations (SSC). We analyse discharge‐SSC relationships from two small streams of similar hydrology, climate and land use but widely different bed compositions (one dominated by sand, the other by gravel). Given that sand‐dominated systems have more fine sediment available for transport, we use bed composition and the relative proportion of surface sand and gravel to be representative of in‐channel sediment supply. Both high flow events and lower flows associated with onset and late recessional storm flow (‘low flows’) are analysed in order to distinguish external from in‐channel sources of sediment and to assess the relationship between low flows and sediment supply. We find that SSC during low flows is affected by changes to sediment supply, not just discharge capacity, indicated by the variation in the discharge‐SSC relationship both within and between low flows. Results also demonstrate that suspended sediment and discharge dynamics differ between reaches; high bed sand fractions provide a steady supply of sediment that is quickly replenished, resulting in more frequent sediment‐mobilizing low flow and relatively constant SSC between floods. In contrast, SSC of a gravel‐dominated reach vary widely between events, with high SSC generally associated with only one or two high‐flow events. Results lend support to the idea that fine sediment is both more available and more easily transported from sand‐dominated streambeds, especially during low flows, providing evidence that bed composition and in‐channel sediment supplies may play important roles in the mobilization and transport of fine sediment. In addition, the analysis of low‐flow conditions, an approach unique to this study, provides insight into alternative and potentially significant factors that control fine sediment dynamics. Copyright © 2007 John Wiley & Sons, Ltd.     

Influence of bed clusters and size gradation on operational time distribution for non‐uniform bed‐load transport

The operational time distribution (OTD) defines the time for bed‐load sediment spent in motion, which is needed to characterize the random nature of sediment transport. This study explores the influence of bed clusters and size gradation on OTD for non‐uniform bed‐loads. First, both static and mobile bed armouring experiments were conducted in laboratorial flumes to monitor the transport of mixed sand/gravel sediments. Only in the mobile armouring experiment did apparent bed clusters develop, because of stable feeding and a longer transport period. Second, a generalized subordinated advection (GSA) model was applied to quantify the observed dynamics of tracer particles. Results show that for the static armour layer (without sediment feed), the best‐fit OTD assigns more weight to the large displacement of small particles, likely because of the size‐selective entrainment process. The capacity coefficient in the GSA model, which affects the width of the OTD, is space dependent only for small particles whose dynamics can be significantly affected by larger particles and whose distribution is more likely to be space dependent in a mixed sand and gravel system. However, the OTD for the mobile armour layer (with sediment recirculation) exhibited longer tails for larger particles. This is because the trailing edge of larger particles is more resistant to erosion, and their leading front may not be easily trapped by self‐organized bed clusters. The strong interaction between particle–bed may cause the capacity coefficient to be space‐dependent for bed‐load transport along mobile armour layers. Therefore, the combined laboratory experiments and stochastic model analysis show that the OTD may be affected more by particle–bed interactions (such as clusters) than by particle–particle interactions (e.g. hiding and exposing), and that the GSA model can quantify mixed‐size sand/gravel transport along river beds within either static or mobile armour layers. Copyright © 2016 John Wiley & Sons, Ltd.     

Graded and uniform bed load sediment transport in a degrading channel

Twenty runs of experiments are carried out to investigate non-equilibrium transport of graded and uniform bed load sediment in a degrading channel. Well-sorted gravel and sand are employed to compose four kinds of sediment beds with different gravel/sand contents, i.e., uniform 100%gravel bed, uniform 100% sand bed, and two graded sediment beds respectively with 53% gravel and 47% sand as well as 22%gravel and 78%sand. For different sediment beds, the experiments are conducted under the same discharges, thereby allowing for the role of sediment composition in dictating the bed load transport rate to be identified. A new observed dataset is generated concerning the flow, sediment transport and evolution of bed elevation and composition, which can be exploited to underpin devel-opments of mathematical river models. The data shows that in a degrading channel, the sand greatly promotes the transport of gravel, whilst the gravel considerably hinders the transport of sand. The promoting and hindering effects are evaluated by means of impact factors defined based on sediment transport rates. The impact factors are shown to vary with flow discharge by orders of magnitude, being most pronounced at the lowest discharge. It is characterized that variations in sand or gravel inputs as a result of human activities and climate change may lead to severe morphological changes in degrading channels.     

Evolution of an advancing gravel front: observations from Vedder Canal,British Columbia

Channelization of the lowermost part of Vedder River in 1922 initiated a natural experiment relevant to the unresolved question of how abrupt gravel–sand transitions develop along rivers. The new channel (Vedder Canal) had a fine bed and a much lower slope than the gravel‐bed river immediately upstream. Changes in morphology and sedimentology as gravel advanced into and along the Canal are documented using air photos, historical surveys, and fieldwork. The channel aggraded and steepened until stabilized by occasional gravel extraction in recent decades. The deposited material fines progressively along the Canal but the gravel front has retained an abrupt appearance because it has advanced by the sequential development of discrete gravel tops on initially sandy alternate bars. Near the gravel front the bed is highly bimodal and there is a sharper drop in the extent of gravel‐framework surface facies than in bulk gravel content. Ahead of the front, gravel is restricted to thin ribbons which often become buried by migrating sand. Calculations show that even though the gravel bed at the head of the Canal is almost unimodal, size‐selective transport during floods can account for the strong bimodality farther downstream. Copyright © 2011 John Wiley & Sons, Ltd.     

Distribution and species composition of macroinvertebrates in the hyporheic zone of bed sediment

The hyporheic zone is a layer of substrate on a river bed where benthic animals normally live,grow,feed,reproduce,and exist for any portion of their life cycle.The hyporheic zone was studied by samplin...     

Water‐worked gravel beds in laboratory flumes – a natural analogue?

An investigation has been conducted to identify the key parameters that are likely to scale laboratory sediment deposits to the field scale. Two types of bed formation were examined: one where sediment is manually placed and screeded and the second where sediment is fed into a running flume. This later technique created deposits through sequential cycles of sediment transport and deposition. Detailed bed surface topography measurements have been made over a screeded bed and three fed beds. In addition, bulk subsurface porosity and hydraulic conductivity have been measured. By comparing the four beds, results revealed that certain physical properties of the screeded bed were clearly different from those of the fed beds. The screeded bed had a random organization of grains on both the surface and within the subsurface. The fed beds exhibited greater surface and subsurface organization and complexity, and had a number of properties that closely resembled those found for water‐worked gravel beds. The surfaces were water‐worked and armoured and there was preferential particle orientation and direction of imbrication in the subsurface. This suggested that fed beds are able to simulate, in a simplified manner, both the surface and subsurface properties of established gravel‐bed river deposits. The near‐bed flow properties were also compared. It revealed that the use of a screeded bed will typically cause an underestimation in the degree of temporal variability in the flow. Furthermore, time‐averaged streamwise velocities were found to be randomly organized over the screeded bed but were organized into long streamwise flow structures over the fed beds. It clearly showed that caution should be taken when comparing velocity measurements over screeded beds with water‐worked beds, and that the formation of fed beds offers an improved way of investigating intragravel flow and sediment–water interface exchange processes in gravel‐bed rivers at a laboratory scale. Copyright © 2008 John Wiley & Sons, Ltd.     

Controls on the aerodynamic roughness length and the grain‐size dependence of aeolian sediment transport

Estimates of the wind shear stress exerted on Earth's surface using the fully rough form of the law‐of‐the‐wall are a function of the aerodynamic roughness length, z₀. Accurate prediction of aeolian sediment transport rates, therefore, often requires accurate estimates of z₀. The value of z₀ is determined by the surface roughness and the saltation intensity, both of which can be highly dynamic. Here we report field measurements of z₀ values derived from velocity profiles measured over an evolving topography (i.e. sand ripples). The topography was measured by terrestrial laser scanning and the saltation intensity was measured using a disdrometer. By measuring the topographic evolution and saltation intensity simultaneously and using available formulae to estimate the topographic contribution to z₀, we isolated the contribution of saltation intensity to z₀ and document that this component dominates over the topographic component for all but the lowest shear velocities. Our measurements indicate that the increase in z₀ during periods of saltation is approximately one to two orders of magnitude greater than the increase attributed to microtopography (i.e. evolving sand ripples). Our results also reveal differences in transport as a function of grain size. Each grain‐size fraction exhibited a different dependence on shear velocity, with the saltation intensity of fine particles (diameters ranging from 0.125 to 0.25 mm) saturating and eventually decreasing at high shear velocities, which we interpret to be the result of a limitation in the supply of fine particles from the bed at high shear velocities due to bed armoring. Our findings improve knowledge of the controls on the aerodynamic roughness length and the grain‐size dependence of aeolian sediment transport. The results should contribute to the development of improved sediment transport and dust emission models. © 2018 John Wiley & Sons, Ltd.     

Simulations demonstrating interaction between coarse and fine sediment loads in rain‐impacted flow

Rain‐impacted flows dominate sheet and interrill erosion and are important in eroding soil rich in nutrients and other chemicals which may have deleterious effects on water quality. Erosion in rain‐impacted flow is associated with raindrop detachment followed by transport either by the combination of flow velocity and raindrop impact (raindrop‐induced flow transport, RIFT) or the inherent capacity of the flow to transport detached material. Coarse particles tend to be transported by RIFT, while fine particles tend to be transported without any assistance from raindrop impact. Because the transport process associated with coarse particles is not 100 per cent efficient, it generates a layer of loose particles on the soil surface and this layer protects the underlying soil from detachment. Simulations were performed by modelling the uplift and downstream movement of both fine and coarse particles detached from the soil surface by individual raindrop impacts starting with a surface where no loose material was present. The simulations produced a flush of fine material followed by a decline in the discharge of fine material as the amount of loose material built up on the bed. The decline in the discharge of fine material was accompanied by an increase in the discharge of coarse material. The relative amounts of coarse and fine material discharged in the flow varied with flow velocity and cohesion in the surface of the soil matrix. The results indicate that the discharge of various sized sediments is highly dependent on local soil, rain and flow conditions and that extrapolating the results from one situation to another may not be appropriate. Copyright © 2006 John Wiley & Sons, Ltd.     

Bedload: a granular phenomenon

Bedload, the transport of sediment remaining in contact with the stream bed, has mainly been studied from the perspective of the correlation between fluid driving forces and the responding sediment flux. Yet grain–grain interactions are important and bedload should also be considered as a granular phenomenon. We review progress made recently in the study of granular flows, especially on segregation and rheology, that better illuminates the nature of bedload. Granular flows may exhibit gas‐like or fluid‐like flow, or quasi‐solid deformation. All three conditions might be duplicated in bedload. Understanding of intense bedload transport occurring continuously in a layer several grains deep – typical of sand beds – might greatly benefit from results in granular physics, as illustrated by grain‐inspired bedload results. However, processes restricted to the surface of the bed, when particles move intermittently and the bed becomes structured, while characteristic in gravel‐bed channels, are not well addressed in granular physics. Mutual study of these phenomena may benefit both physics and fluvial geomorphology. We intend, therefore, to contribute to an enhanced dialogue between granular physics and bedload science communities. Copyright © 2010 John Wiley & Sons, Ltd.     

Downstream fining in contrasting reaches of the sand‐bedded Yellow River

Compared to downstream fining of a gravel‐bedded river, little field evidence exists to support the process of downstream fining in large, fine sand‐bedded rivers. In fact, the typically unimodal bed sediments of these rivers are thought to produce equal mobility of coarse and fine grains that may discourage downstream fining. To investigate this topic, we drilled 200 sediment cores in the channel beds of two fine‐grained sand‐bedded reaches of the Yellow River (a desert reach and a lower reach) and identified a fine surface layer (FSL) developed over a coarse subsurface layer (CSL) in the 3‐m‐thick bed deposits. In both reaches downstream, the thickness of the FSL increased, while that of the CSL decreased. Comparison of the depth‐averaged median grain sizes of the CSL and the FSL separately in both reaches shows a distinct downstream fining dependence to the median grain size, which indicates that at a large scale of 600‐800 km, the CSL shows a significant downstream fining, but the FSL shows no significant trends in downstream variations in grain size. This result shows that fine sediment supply (<0·08 mm median grain size) from upstream, combined with lateral fine sediment inputs from tributaries and bank erosion, can cause a rapid fining of the downstream channel bed surface and can develop the FSL layer. However, in the desert reach, lateral coarse sediment supply (>0·08 mm median grain size) from wind‐borne sediments and cross‐desert tributaries can interrupt the FSL and coarsen the channel bed surface locally. Copyright © 2011 John Wiley & Sons, Ltd.     

STREAM-SUBSURFACE EXCHANGE, SUSPENDED SEDIMENT TRANSPORT, AND THE COUPLED TRANSPORT OF COLLOIDS AND CONTAMINANTS IN SEDIMENT BEDS

1 INTRODUCTION Alluvial streams generally have permeable bed sediments that can admit significant pore water flows. Steady flow of surface water over bed roughness features such as sand waves or pools and riffles can then drive water flow into and out of the shallow subsurface. This is often termed hyporheic exchange, and the subsurface region where mixing between stream and ground waters occurs is the hyporheic zone (Hynes, 1983). The hyporheic zone has been shown to be a critical com…     

Evaluating fine sediment mobilization and storage in a gravel‐bed river using controlled reservoir releases

Two controlled flow events were generated by releasing water from a reservoir into the Olewiger Bach, located near Trier, Germany. This controlled release of near bank‐full flows allowed an investigation of the fine sediment (<63 µm) mobilized from channel storage. Both a winter (November) and a summer (June) release event were generated, each having very different antecedent flow conditions. The characteristics of the release hydrographs and the associated sediment transport indicated a reverse hysteresis with more mass, but smaller grain sizes, moving on the falling limb. Fine sediment stored to a depth of 10 cm in the gravels decreased following the release events, indicating the dynamic nature and importance of channel‐stored sediments as source materials during high flow events. Sediment traps, filled with clean natural gravel, were buried in riffles before the release of the reservoir water and the total mass of fine sediment collected by the traps was measured following the events. Twice the mass of fine sediment was retained by the gravel traps compared with the natural gravels, which may be due to their altered porosity. Although the amount of fine sediment collected by the traps was not significantly related to measures of gravel structure, it was found to be significantly correlated to measures of local flow velocity and Froude number. A portion of the traps were fitted with lids to restrict surface exchange of water and sediment. These collected the highest amounts of event‐mobilized sediments, indicating that inter‐gravel lateral flows, not just surface infiltration of sediments, are important in replenishing and redistributing the channel‐stored fines. These findings regarding the magnitude and direction of fine sediment movement in gravel beds are significant in both a geomorphic and a biological context. Copyright © 2006 John Wiley & Sons, Ltd.     

Regional grain size variations in aeolian sediments along the transition between Tibetan highlands and north‐western Chinese deserts – the influence of geomorphological settings on aeolian transport pathways

Sediment distribution is investigated applying grain size analysis to 279 surface samples from the transitional zone between high mountains (Qilian Shan) and their arid forelands (Hexi Corridor) in north‐western China. Six main sediment types were classified. Medium scale (10³ m) geomorphological setting is carefully considered as it may play an important role concerning sediment supply and availability. A tripartite distribution of sedimentological landscape units along the mountain to foreland transition is evident. Aeolian sediments (e.g. loess and dune sands) are widespread. They are used to identify aeolian transport pathways. The mU/fS‐ratio (5–11 µm/48–70 µm) among primary loess opposes the two grain size fractions being most sensitive to varying accumulation conditions. The first fraction is attributed to long‐distance transport in high suspension clouds whereas the latter represents local transport in saltation mode. The ratio shows strong correlation with elevation (R² = 0.77). Thus, it indicates a relatively higher far‐traveled dust supply in mountainous areas (>3000 m above sea level [a.s.l.]) compared to the foreland. The contribution of westerlies to high mountain loess deposits is considered likely. Hereby, the influence of the geomorphological setting on grain size composition of aeolian sediments becomes apparent: the contribution from distant dust sources is ubiquitous in the study area. However, the far‐distance contribution may be reduced by the availability of fine sand provided in low topography settings. Plain foreland areas support fine sand deflation from supplying river beds, allowing the formation of sandy loess in foreland areas and intramontane basins. In contrast, high mountain topography inhibits strong sand deflation into loess deposits. Eastern parts of the Hexi Corridor show higher aeolian sand occurrence. In contrast, the western parts are dominated by gravel gobi surfaces. This is attributed to higher sand supply in eastern parts provided by the Badain Jaran Desert and fluvial storages as sand sources. Copyright © 2014 John Wiley & Sons, Ltd.     

Suspended sediment transport during tropical‐cyclone floods in Fiji

Flow records, rising‐stage sediment samplers, and a sand suspension model are used to examine suspended sediment concentrations during major floods caused by tropical cyclones TC Joni and TC Kina in the Rewa River, Fiji. The highest concentrations of total suspended solids were measured during the early stages of TC Kina. The suspension model predicts higher sand concentrations for TC Kina compared with TC Joni because of the larger slope and higher shear stresses during Kina. Extremely high wash load concentrations early in TC Kina are at least partly due to remobilization of fine sediment deposited during the earlier TC Joni flood. Samples from the TC Kina had volumetric concentrations larger than 5%, indicating hyperconcentrated streamflows. Mass‐density shear stresses in the hyperconcentrated flows are up 1·6 times larger than clear‐water shear stresses, but they occur early during low stages of the flood and probably do not result in severe bed erosion. Copyright © 2002 John Wiley & Sons, Ltd.     

Examining the physical components of boundary shear stress for water‐worked gravel deposits

It is argued in this commentary that, in order to understand better the physical mechanisms that generate boundary shear stress over water‐worked gravel beds, flow velocity data should be re‐evaluated by spatial averaging the Reynolds equations to produce time‐ and space‐averaged (double‐averaged) momentum equations. A series of laboratory experiments were conducted in which the flow velocities were measured using a PIV system over two water‐worked gravel deposits. Combined with detailed data on the bed surface topography and vertical porosity, the physical components of shear stress were obtained. This enabled the various momentum transfer mechanisms present above, within and at the interface of a porous, fluvial deposit, to be quantified. This included the examination of the relevant contributions of temporal and spatial fluctuations in velocity and surface drag to the overall momentum transfer. It is demonstrated that double‐averaging represents a logical framework for assessing the fluid forces responsible for sediment entrainment and for investigating intragravel flow and sediment–water interface exchange mechanisms within the roughness layer in water‐worked gravel deposits. By considering the physical components of shear stress and their relative sizes it was possible to provide a physically based explanation for existing observations of enhanced mobility of gravel–sand mixtures and the transfer of solutes into porous, gravel deposits. This analysis reveals the importance of obtaining co‐located, high quality spatial data on the flow field and bed surface topography in order to gain a physical understanding of the mechanisms which generate boundary shear stress. Copyright © 2010 John Wiley & Sons, Ltd.     

Streambed restoration to remove fine sediment alters reach‐scale transient storage in a low‐gradient fifth‐order river,Indiana, USA

Hyporheic restoration is of increasing interest given the role of hyporheic zones in supporting ecosystem services and functions. Given the prevalence of sediment pollution to waterways, an emerging restoration technique involves the removal of sediment from the interstices of gravel‐bed streams. Here, we document streambed sediment removal following a large, accidental release of fine sediment into a gravel‐bed river. We use this as a natural experiment to assess the impact of fine sediment removal on reach‐scale measures of transient storage and to document the responses of reaches with contrasting morphology (restored vs. unrestored) to changing discharge one‐field season. We conducted a series of conservative solute tracer experiments in each reach, interpreting both summary statistics for the recovered in‐stream solute tracer time series. Additionally, we applied the transient storage model to interpret the results via model parameters, including a Monte Carlo analysis to measure parameter identifiability and sensitivity in each experiment. Despite the restoration effort resulting in an open matrix gravel bed in the restored reach, we did not find the significant differences in most time series metrics describing reach‐scale transport and transient storage. We hypothesize that this is due to enhanced vertical exchange with the gravel bed in the restored reach replacing lateral exchange with macrophyte beds in the unrestored reach, developing a conceptual model to explain our findings. Consequently, we found that the impact of reach‐scale removal of fine sediment is not measureable using reach‐scale solute tracer studies. We offer recommendations for future studies seeking to measure the impacts of stream restoration at the reach scale.     

Size sorting of fine-grained sediments during erosion: Results from the western Gulf of Lions

Sediment cores from the western Gulf of Lions France were subject to known bottom shear stresses with the goal of understanding size-specific sediment erodibility. On cruises in October 2004, February and April 2005, cores with an undisturbed sediment–water interface were collected along a transect extending seaward from the Tet river mouth. The cores were exposed to increasing shear stresses (0.01–0.4 Pa) onboard the vessel shortly after collection by using a Gust erosion chamber. Samples of the suspensate were collected during the erosion experiments and analyzed for disaggregated inorganic grain size (DIGS) using a Coulter Multisizer IIe. Size-specific mobility plots were generated by dividing the proportion of each grain size in suspension at each shear stress by its proportion in the sediment before erosion. If all grain sizes that make up the bottom sediment are eroded equally from the bed, then mobility equals one for all grain sizes. Values >1 indicate that the suspended sediment is enriched in the size class and values <1 indicate that the size class is enriched in the bed. Results show that in non-cohesive, sandy silts, fine grains (clays and fine silts) are eroded preferentially from the bed at low shear stresses. With increasing bottom stress progressively larger grains are eroded from the bed. In cohesive silts, preferential erosion of the finer sizes no longer occurs, with all sizes up to medium silts eroding at approximately the same rate. Effectively, a sandy silt can be winnowed of its fine grain fraction during erosion while cohesive silts cannot. This difference in the sortability of cohesive and non-cohesive sediment during erosion may control the position and maintenance of the sand–mud transition and the sequestration of surface-adsorbed contaminants.