室温下制备以{211}晶面为主的Ti1-xVxO2薄膜及其可见光催化性能

以金属Ti和V作为靶材,采用直流反应共溅射技术在室温下制备了以{211}晶面为主的锐钛矿相Ti_1-xV_xO₂薄膜,研究了不同V靶功率对Ti_1-xV_xO₂薄膜的薄膜成分、晶相结构和可见光催化性能的影响。研究表明,Ti_1-xV_xO₂薄膜的晶相结构为锐钛矿相,择优取向为(211),而结晶度受V靶功率的影响。随着V靶功率的增加,薄膜中V元素含量逐渐增加,同时,晶粒和沉积速率也逐渐增加。另外,当V靶功率为150 W时,薄膜的表面粗糙度值有一个最大值。V的掺杂导致薄膜的能带间隙变窄,对光的吸收向可见光区偏移,从而有效地改善了薄膜的可见光催化能力。当V靶功率为150 W时,Ti_1-xV_xO₂薄膜的能带间隙值为 2.82 eV,其在2 h的可见光照射下分解了80%的RhB染料。这被归结于能带间隙窄,高能晶面{211}和结晶度高的共同作用。     

BaCe0.8-xNbxGd0.2O3-δ(0≤x≤0.45)的制备及性能研究

采用高温固相反应法制备了质子导体BaCe_0.8-xNb_xGd_0.2O_3-δ(0≤x≤0.45)。结合XRD、SEM、EIS等技术对其物相、微观形貌、稳定性及电导率进行了研究。结果表明,在1 600 ℃烧结5 h制备的质子导体BaCe_0.8-xNb_xGd_0.2O_3-δ(0≤x≤0.45)均能保持主相为斜方晶的钙钛矿结构。Nb的加入可明显提高烧结样品的致密性及在CO₂和水蒸气气氛下的稳定性。在湿润H₂/Ar(0.4%,V/V)气氛中800 ℃下,x=0.1样品的电导率为5.73 mS·cm^-1,电导活化能为0.35 eV,与x=0的样品相当。     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

层状O2结构锂锰氧化物Li0.60[MgxCoyMn1-x-y]O2的制备及结构表征

本文采用离子交换法分别制备了双复合锂锰氧化物Li_0.60[Mg_xMn_1-x]O₂(0.05 ≤ x ≤ 0.15)和三复合锂锰氧化物Li_0.60[Mg_xCo_yMn_1-x-y]O₂(x=0.05，0.05 ≤      

CexPr1-xO2-δ复合氧化物的XRD和Raman表征

A series of Ce_xPr_1-xO_2-δ mixed oxides were synthesized by sol-gel method and characterized by Raman and XRD techniques. When x value was changed from 1.0 to 0.5, only a cubic phase CeO₂ was observed. The samples were very well crystallized on decreasing x from 0.50 to 0.99. For Ce_xPr_1-xO_2-δ samples 465 cm^-1 and 1 150 cm^-1 Raman peaks are attributed to the Raman active F_2g mode of CeO₂. The broad peak at about 570 cm^-1 in the region of 0.3 ≤x≤ 0.99 can be linked to lattice defects resulting in oxygen vacancies. The new band at about 195 cm^-1 may be attributed to the asymmetric vibration caused by the formation of oxygen vacancies. Calcination temperatures had great effect on the peak intensity for CeO₂ but less effect on Ce_0.8Pr_0.2O_2-δ in Raman spectra. It might be due to the transformation of the colors for the mixed oxides, the insertion of Pr atom into the ceria lattice could enhance the sintering resistance and thermal stability of the mixed oxides.     

La2-xBixCuO4阴极材料的合成与电化学性质

采用甘氨酸-硝酸盐法合成了固体氧化物燃料电池阴极材料La_2-xBi_xCuO₄（x=0、0.05、0.10）,并利用X射线衍射（XRD）对材料的物相进行分析。结果表明,La_2-xBi_xCuO₄形成单一的类钙钛矿结构氧化物,且晶胞体积随着铋掺杂量的增加而增大。在950℃烧结24 h过程中,La_2-xBi_xCuO₄不与电解质Sm_0.2Ce_0.8O_1.9（SDC）发生反应,表明这种电解质材料具有良好的高温化学相容性。电导率测试结果表明Bi的掺入显著提高了材料电导率。程序升温脱附测试结果表明,铋的掺杂显著增强了材料的表面氧吸附能力。不同氧分压下的交流阻抗谱测试结果表明,La_1.9Bi_0.1CuO₄阴极在700℃空气中的极化电阻为0.26 Ω·cm²,以电解质SDC支撑的单电池NiO-SDC/SDC/La_1.90Bi_0.10O₄在700℃的最大输出功率密度为308 mW·cm^-2,电极反应的速控步骤为氧分子的扩散与表面吸附过程。     

掺镍型层状LixNiyMn1-yO2正极材料的合成与电性能研究

A kind of cathode material of layered Li_xNi_yMn_1-yO₂ characterized with the O2 type has been synthesized by a simple method. Its precursor Na_xNi_yMn_1-yO₂ has been prepared from manganese dioxide， nickel hydroxide and sodium carbonate at high temperature in air and quickly cooled in cold water， then it has been exchanged by the melted LiNO₃ at 300～400℃ in air. The effects of calcine-temperature for the precursors and its compositions (the content of Na and Ni) on the electrochemical properties of the material Li_xNi_yMn_1-yO₂ have been investingated by XRD and electrochemical tests. The results show that the sample Li_0.7Ni_0.3Mn_0.7O₂， has the best electrochemical properties which shows only one charge-discharge potential stage of 2.8～3.0V and has a high specific capacity over 180mAh·g^-1 cycled between 2.0～4.20V. A significant structure transformation to the spinal-type phase has not been found in the charge-discharge cycling and the discharge specific capacity around 165mAh·g^-1 has re-mained after the 20th cyclings for the material.     

LiNi1-xMxVO4的红外光谱和拉曼光谱研究

The vanadates of LiNi_1-xM_xVO₄(M=Fe,Co,Ni) containing VO₄ tetrahedrons were synthesized by soft chemical method through a new mild liquid route. The samples sintered at 450℃ for 3h and at 650℃ for 3h are named for LT-LiNiVO₄ and for MT-LiNi_1-xM_xVO₄ respectively. All of the products were measured by X-ray diffraction, IR and Raman spectra respectively. In comparison with IR spectra of V₂O₅ and NiO, the LT-LiNiVO₄ has a strong and broad IR absorption band of VO₄ tetrahedrons located at 600～850cm^-1 with three small splitting peaks corresponding to the asymmetry stretching vibrations of V-O bonds. The results of IR and Raman spectra for MT-LiNi_1-xM_xVO₄ show that the cations of Ni²⁺, Co²⁺, Fe²⁺ have the influences on the frequency shifts of the V-O vibrations.     

Ba0.98Bi0.02(Ti0.9Zr0.1)1-xCuxO3陶瓷的介电性能、弛豫行为与结晶化学特性

采用固相合成法, Bi3+作施主掺杂A位, Cu₂₊作受主掺杂B位, 制备了Ba_0.98Bi_0.02(Ti_0.9Zr_0.1)_1-xCu_xO₃(x=0, 0.01, 0.02, 0.03)陶瓷样品。借助XRD、LCR等研究了该陶瓷的结构与介电性能。结果表明:当x=0.03时, 陶瓷样品出现第二相。通过GULP模拟, 缺陷偶极子的稳定性从低到高依次为:[2Bi_Ba^·+V_Ba"]、[2Bi_Ba^·+Cu_Ti/Zr"]、[Cu_Ti/Zr"+V_O^··], 结合实验可知:介电弛豫程度与晶体中缺陷偶极子的存在形式相关, 其中x=0.01时, 晶体中以[2Bi_Ba^·+Cu_Ti/Zr"]为主。随Cu₂₊掺杂量的增加, 介电常数增加, 介电常数与B位键价和呈反比变化、与八面体BO₆的体积呈正比变化。     

纳米Ce1-xLaxO2-δ的微波引诱燃烧合成及其性能表征

Nanometer Ce_1-xLa_xO_2-δ solid solutions were synthesized by microwave-induced combustion process us-ing cerium nitrate hexahydrate， lanthanum nitrate hexahydrate and urea as raw materials. The process took only six minutes to obtain La₂O₃-doped CeO₂ nanopowders. The nanopowders were characterized by XRD， Laser Raman spectrum ， UV-Vis spectroscopy，field-emission scanning electron micrograph(FE-SEM)and TEM. The results revealed that the grain size of Ce_1-xLa_xO_2-δ varied from 20 to 40 nm calculated by Scherer formula through the plane of (111)， that oxygen vacancy was produced in the crystal lattices and the concentration of oxygen vacancy was increased with La doping， therefore the covalence of Ce-O bond was strenthened， which results in more intensive UV-C(200～280 nm)absorption. It can be seen from SEM that the porous appearance was obtained. Grain size is no more than 40nm observed from TEM.     

固溶体Bi_2Mo_(1-x)W_xO_6的水热合成及光催化性能

采用水热法,在较低温度下合成了系列Bi2Mo1-xWxO6固溶体。结果表明,W的替代抑制了固溶体的晶粒生长,导致了较小的晶粒尺寸。随着x的增加,红外光谱中840cm-1处M-O键的振动频率νM-O有规律地向低频率方向移动,表明Mo6+离子逐步被W6+替代,生成了无限互溶的固溶体。光吸收性能研究表明,随着W6+逐步替代Mo6+,带隙出现了先降后升的趋势,x=0.4时带隙最小。而固溶体的光催化性能随着x的增加,出现了先增后减的趋势,x=0.4时光催化活性最高。此外,含W样品的光催化活性高于Bi2MoO6。这与固溶体的带隙、带结构和晶粒尺寸变化有关。     

室温电化学沉积Ba1-xCaxMoO4多晶固溶体薄膜

近年发展起来的制备功能薄膜的电化学沉积技术,是软溶液工艺路线(Soft Solution Processing简记为SSP)中的重要技术[1]。与传统的薄膜制备技术相比,电化学沉积技术在反应控制、形貌控制、沉积速度、能量消耗、环境影响、薄膜晶化以及沉积设备等方面都有较明显的优势,同时避免了     

SiO2/TiO2-xCx/C的制备、表征及其吸附和可见光催化性能

以SiO2为成核中心,钛酸四丁酯为钛源,分别以多羟基化合物乙二醇、丙三醇、葡萄糖和聚乙烯醇为联接剂,采用水解沉淀法制备了碳掺杂和包覆的多孔SiO2/TiO2-xCx/C可见光响应型光催化剂。采用X-射线衍射(XRD)、透射电子显微镜(TEM)、X-射线光电子能谱(XPS)、傅里叶变换-红外光谱(FTIR)、比表面积(BET)和紫外-可见(UV-Vis)漫反射光谱对样品进行表征。对不同结构样品的形成机理进行了分析。以次甲基蓝(MB)溶液为模拟废水,对样品的吸附性能和可见光催化性能进行了评价。结果表明,多羟基化合物对材料的结构和性能有重要影响。碳的掺杂和包覆使材料的吸收光谱包含了整个可见光区,而多孔结构使材料的吸附性能得到提高。以聚乙烯醇为原料所得样品吸附性能最好,30 min内吸附率达到70%;而以丙三醇为原料所得样品具有最好的可见光催化性能,40 min内次甲基蓝的降解率达到95%。     

NixCo3-xO4表面修饰对CdSe/TiO2纳米管阵列光电化学氧化水活性的影响

利用氨挥发诱导法在CdSe/TiO2纳米管阵列表面负载一层NixCo3-xO4。采用SEM、XRD、XPS、UV-Vis对样品进行表征,通过线性扫描伏安法测定光阳极的释氧电势来评价其光电水氧化活性。结果表明:表面NixCo3-xO4是尖晶石结构;相对于CdSe/TiO2纳米管阵列光阳极,NixCo3-xO4/CdSe/TiO2光阳极能将光电氧化水的过电势降低430 mV。Ni离子的引入使得NixCo3-xO4表面富含三价阳离子(Ni3+,Co3+),从而促进CdSe/TiO2光阳极光电水氧化的进行。     

Bi2WO6量子点(QDs)修饰Bi2MoO6-xF2x异质结的构筑及其催化活性增强机理

采用简单沉积-沉淀法合成了Bi₂WO₆@Bi₂MoO_6-xF_2x（BWO/BMO6-xF2x）异质结,借助XRD、XPS、TEM、SEM、EDS、UV-Vis-DRS、PC和EIS等测试技术对其组成、形貌、光吸收特性和光电化学性能等进行系统表征,并以模型污染物罗丹明B（RhB）的光催化降解作为探针反应来评价Bi₂WO₆@Bi₂MoO_6-xF_2x异质结的光催化活性增强机制。形貌分析表明,所得Bi₂MoO₆微球由大量厚度为20~50 nm的纳米片组成;FE-SEM和HR-TEM分析表明,尺寸约为10 nm的Bi₂WO₆量子点均匀沉积在Bi₂MoO_6-xF_2x微球表面,形成新颖的Bi₂WO₆@Bi₂MoO_6-xF_2x异质结;与纯Bi₂MoO₆或者Bi₂WO₆相比,1∶1Bi₂WO₆@Bi₂MoO_6-xF_2x异质结表现出更好的光催化活性和光电流性质,其对RhB光催化降解的表观速率常数分别为纯BMO和BWO的6.4和11.6倍。PC和EIS图谱分析表明,Bi₂WO₆量子点表面沉积显著提高Bi₂MoO_6-xF_2x光生电子/空穴的分离效率和迁移速率;活性物种捕获实验证明了·O₂^-和h⁺是主要的活性物种。根据实验结果,探讨了F^-掺杂和Bi₂WO₆量子点之间的协同效应对Bi₂MoO₆的光催化活性的影响机制。     

CdS插层的K4Nb6-xCuxO17复合物的制备及其光催化制氢活性

以Nb2O5,K2CO3和CuO为原料经高温固相反应合成K4Nb6-xCuxO17催化剂,并通过层间离子交换反应,胺插入反应以及硫化反应制备CdS插层K4Nb6-xCuxO17复合催化剂(K4Nb6-xCuxO17/CdS)。利用X射线衍射(XRD),X射线光电子能谱(XPS),场发射扫描电镜(SEM),X射线能谱仪(EDX),紫外-可见漫反射(UV-Vis),分子荧光光谱(PL)等技术对催化剂进行表征。考察了催化剂的可见光催化制氢活性。结果表明,Cu离子掺杂进入K4Nb6O17晶格中,CdS位于K4Nb6O17层间。CdS插层K4Nb6-xCuxO17催化剂的最大吸收光波长约为550 nm。催化剂制氢活性有明显提高,紫外光和可见光下3 h产氢量分别达到279.83 mmol.gcat-1和7.11 mmol.gcat-1。最后讨论了复合催化剂光生电荷转移机理。     

纳米微孔NixZn(1-x)Fe2O4的水热合成研究

０引言尖晶石型铁酸盐是一类重要的磁性材料，它可用于防止电磁波辐射设备以及隐身材料中的吸波剂犤１，２犦，具有价格低廉、吸波性能优良的特点。同时尖晶石型铁酸盐也是一类重要的催化剂，９０年代初又发现了氧缺位的该类化合物具有将CO２还原为C的优良催化性能犤３犦。因此，有关铁酸盐的制备及性能研究一直是化学工作者和材料科学工作者感兴趣的领域。随着新的合成方法的不断涌现，对传统铁氧体材料进行结构改造以提高其性能是一个重要的研究发展方向，本文采用模板剂造孔技术，首次在NixZn（１－x）Fe２O４水热合成中选用模板剂，…     

Fabrication and properties of xBiFeO3-(1 − x)Bi4Ti3O12 system by sol–gel process

The thin films of mixture of xBiFeO₃-(1 − x)Bi₄Ti₃O₁₂ (x = 0.4, 0.5, and 0.6) system were prepared by a sol–gel process. The thicknesses of the thin films were 540, 500, and 570 nm, respectively. The crystal structure of all thin films annealed at 650 °C was analyzed by X-ray diffraction. It was found that the thin films at x = 0.4 and 0.5 mainly consisted of a Bi₄Ti₃O₁₂ phase while Bi₅Ti₃FeO₁₅ was the major phase of the thin film at x = 0.6. The thin film (x = 0.6) showed better ferroelectric properties in remnant polarization and polarization fatigue than those observed in the thin films (x = 0.4 and 0.5). The values of remnant polarization 2P _r and coercive field 2E c of the thin film at x = 0.6 were 36 μC/cm² and 192 kV/cm at an applied electric field of 260 kV/cm, respectively. There was almost no polarization fatigue up to 10¹⁰ switching cycles. Also weak ferromagnetism was observed in the thin film at x = 0.6.     

尖晶石型LiMn2-xInxO4(x=0，0.01，0.02，0.05)的合成及电化学性能研究

以醋酸锰、氢氧化锂和三氧化二铟为原料,以柠檬酸为配位剂,采用溶胶-凝胶法制备了掺杂In的尖晶石LiMn2-xInxO4(x=0,0.01,0.02,0.05),采用XRD、SEM对目标材料进行了结构和形貌表征,采用恒流充放电、循环伏安(CV)以及交流阻抗(EIS)谱测试对材料进行了电化学性能表征,考察了不同In掺杂量对材料性能的影响。结果表明,当In掺杂量为1%时,LiMn1.99In0.01O4样品具有纯的尖晶石锰酸锂结构,在0.5C和3.4～4.35 V电压范围条件下,LiMn1.99In0.01O4的初始放电容量为119.9 mAh.g-1,经过1C 30次,2C 30次,再0.5C 5次循环后,其放电容量保持率为84.9%,显示了良好的电化学性能。掺杂1%的In的样品比未掺杂的样品具有更优的高温循环稳定性能。