高效液相色谱法同时测定长春花中的文多灵、长春质碱和脱水长春碱

运用高效液相色谱（HPLC）梯度洗脱同时测定了长春花中的文多灵、长春质碱和脱水长春碱等3种生物碱。色谱柱为Waters 5C18-MS-Ⅱ(4.6 mm×250 mm),流动相为甲醇-1%二乙胺(磷酸调pH至7.3)系统,梯度洗脱,检测波长220 nm,柱温25 ℃。实验结果表明,文多灵、长春质碱和脱水长春碱等3种生物碱分别在0.03～1 mg/mL,0.03～1 mg/mL和0.01～0.5 mg/mL时线性关系良好,平均加样回收率分别为96.8%,97.0%和96.4%,相对标准偏差(RSD)分别为1.53%,1.37%和1.96%。用该法同时检测了不同干旱条件处理下长春花样品中的文多灵、长春质碱和脱水长春碱,方法准确、快速、简便。     

树脂法分离纯化倒提壶生物碱的研究

采用阳离子交换树脂和大孔吸附树脂联用的方法,将倒提壶生物碱提取液依次经过阳离子交换树脂和两次大孔吸附树脂,对其中的天芥菜碱和毛果天芥菜碱进行分离纯化。结果表明,倒提壶生物碱溶液采用阳离子交换树脂经过水洗和NaCl洗脱与大孔吸附树脂两次经乙醚和50%乙醇洗脱后,毛果天芥菜碱与天芥菜碱的纯度分别从0.73%和2.2%提高至81.6%和79.2%,提取量分别由4.6 mg/g和10.7 mg/g提高至50.6mg/g和92.7 mg/g。该文所建立的分离纯化方法具有成本低、污染小、周期短、操作简便和分离纯化效率高等特点,适合工业化生产。     

吸附树脂分离纯化枇杷花总黄酮的研究

比较了D-101、D-160、AB-8、NKA-9和聚酰胺等5种吸附树脂对枇杷花总黄酮的吸附及解吸附性能。在静态吸附和动态吸附实验基础上,筛选出效果较好的AB-8树脂进行动态吸附参数的研究。考察了样品液pH值、样品液浓度、洗脱液浓度、上样速度、洗脱速度等对AB-8树脂吸附和解吸效果的影响,确定了AB-8树脂动态吸附枇杷花总黄酮的最佳条件。获得的最佳纯化条件如下,样品液pH值为5.5,样品液浓度为12mg/mL,洗脱液为30%的乙醇水溶液,上样速度为2BV/h,洗脱速度为1BV/h。纯化后样品总黄酮含量达86.7%,比纯化前总黄酮含量高5~6倍。实验结果表明,AB-8树脂可用于分离纯化枇杷花总黄酮。     

大孔树脂分离纯化藏药白花龙胆花总黄酮的研究

考察了HPD-826、HPD-417、ADS-17、HPD-722、HPD-450、AB-8、HPD-600、D-101,共8种大孔树脂对藏药白花龙胆花总黄酮的吸附和解吸性能,通过静态吸附量和解吸附率及静态吸附曲线的绘制,筛选出AB-8树脂的效果最佳;以AB-8树脂为目标,进行了动态吸附实验,考察了上柱液浓度、pH值、上柱液流速、乙醇浓度、解吸剂流速、解吸体积等对AB-8树脂吸附和解吸效果的影响,确定出AB-8树脂动态吸附白花龙胆花总黄酮的最佳条件:上柱液浓度为6.5mg/mL,pH为3.79,上柱流速4BV/h;最佳洗脱条件:用50%乙醇进行洗脱,解吸流速为3BV/h,解吸体积4BV。在此条件下,白花龙胆花总黄酮纯度由原来的22.10%,变为65.75%,产品精制倍数为65.75%/22.10%=2.97,表明AB-8树脂可用于白花龙胆花总黄酮的分离纯化。     

大孔树脂D-101纯化黑骨藤复方药物有效部位工艺研究

选取D-101型大孔树脂,以总黄酮、总萜和总生物碱的转移率评价上样质量浓度、上样量、吸附时间和洗脱液体积流量对纯化效果的影响,以落干酸、6'-O-β-D-葡萄糖基龙胆苦苷、獐牙菜苦苷、龙胆苦苷、獐牙菜苷、杠柳苷、延胡索乙素、四氢小檗碱和延胡索甲素的转移率评价洗脱液浓度对纯化效果的影响,以延胡索甲素的转移率确定洗脱终点,最终优化出最佳纯化工艺条件:上样质量浓度75mg/mL,样品:填料为1:70,吸附时间为2h,洗脱液体积流量为4.0mL/min,洗脱条件为先用3BV蒸馏水除杂,再依次用2BV 30%乙醇、2BV 60%乙醇和10BV95%乙醇洗脱。该纯化工艺稳定可行,可作为黑骨藤复方药物有效部位制备工艺。     

固相萃取富集-高效液相色谱法测定长春花中的3种内源激素

植物内源激素直接参与植物生命的所有活动。激素在植物中的含量极低,且性质不稳定,加上长春花（Catharan．thusroseus（L_）G．Don）中文多灵（vindoline）、长春质碱（catharanthine）等众多生物碱类的干扰,使得长春花植物内源激素的测定十分困难。目前对于长春花中内源激素的分离和检测尚未见报道。本文以固相萃取和高效液相色谱法测定了长春花中的3种内源激素含量,取得了理想的效果。     

SP700大孔树脂纯化酸枣仁中三萜总皂苷的研究

从7种极性不同的大孔树脂中筛选出一种对酸枣仁三萜总皂苷具有良好吸附和解吸性能的树脂—三菱SP700树脂。静态实验中,该树脂的最高吸附容量可达131.0mg皂苷/g树脂,皂苷在树脂表面的吸附符合Langmuir模型,用体积分数为90%的乙醇解吸得率最高可达97.8%;动态实验中,样液在膨胀床模式下上样,树脂的平均动态吸附容量为15mg皂苷/g树脂,上样后,用体积分数分别为50%和90%的乙醇溶液进行分段洗脱,洗脱得率最高可达到95.1%,经过纯化的皂苷提取物的含量提高了4倍。SP700大孔吸附树脂作为一种对酸枣仁中三萜总皂苷进行纯化的介质具有良好的性能和应用价值。     

大孔吸附树脂纯化石蒜中石蒜碱

比较了9种大孔吸附树脂对石蒜碱的吸附率和解吸率,确定了HPD300为优选吸附树脂,研究了该树脂纯化石蒜碱的条件及参数. 室温下,9 BV 1.22 g/L的石蒜碱上样液以2 BV/h过柱,4 BV水以2 BV/h洗涤后用8 BV 70%乙醇以2 BV/h洗脱,石蒜碱的纯度由9.93%提高至23.07%.     

大孔吸附树脂富集纯化柴胡总皂苷的研究

以柴胡皂苷a为指标,采用高效液相色谱法测定洗脱液中柴胡皂苷a的含量,考察D-101大孔吸附树脂对柴胡总皂苷的吸附性能和洗脱条件,以柴胡提取液15 mL(0.2 g药材/mL)上柱,70%的乙醇洗脱,柴胡总皂苷洗脱率为71.83%.且除杂能力强.     

树脂吸附法分离纯化桑叶总黄酮——（Ⅱ）动态法分离桑叶总黄酮的工艺条件及数学模拟

考察了H103树脂固定床吸附分离桑叶总黄酮的工艺参数,并对吸附工艺进行了数学模拟和比较.实验结果表明,H103树脂固定床吸附分离桑叶总黄酮在上样浓度6.05mg/mL时,以9mL/min上样,吸附完全后用60%乙醇以4.5mL/min流速洗脱,桑叶总黄酮产品的回收率为90.57%,纯度为76.33%,建立的固定床吸附模型为预测固定床吸附桑叶水提液中桑叶黄酮达到穿透点时间及固定床吸附容量提供了准确、快捷的方法.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.