免疫亲和柱净化/柱前衍生化-高效液相色谱荧光检测法测定粮谷中的T-2毒素

建立了免疫亲和柱净化/柱前衍生化-高效液相色谱荧光检测器测定粮谷中T-2毒素含量的方法。样品经甲醇-水(体积比为80∶20)混合溶剂提取,通过免疫亲和柱(IAC)净化,以氰酸蒽(1-AN)为衍生化试剂、4-二甲基氨基吡啶(DMAP)为催化剂进行衍生,以ZORBAX Eclipse XDB-C18 柱为分离柱,乙腈-水(体积比为80∶20)为流动相进行高效液相色谱分离及荧光检测，荧光检测的激发波长为381 nm，发射波长为470 nm。T-2毒素的质量浓度为0.01~1.5 mg/L时与峰高呈良好的线性,相关系数为0.9985。在0.01~1.5 μg/g添加水平下，回收率为79.7%~94.5%,相对标准偏差小于7%；检出限（S/N＝3）为0.01 μg/g。该方法净化效果好,灵敏度高,操作简便快速。     

免疫亲和柱净化-液相色谱质谱法对粮谷中T-2与HT-2毒素的测定

建立了免疫亲和柱净化-液相色谱质谱法同时检测粮谷中T-2和HT-2毒素的方法.样品经乙腈-水(体积比80∶20)混合溶剂提取,免疫亲和柱(Bond ElutMycotoxin)净化后,采用液相色谱质谱(HPLC-MS)测定.T-2和HT-2毒素在0.005～0.5 mg/L范围内线性关系良好,相关系数均大于0.999 0;在0.01、0.05、0.10、0.2 mg/kg的加标水平下,2种毒素的平均回收率为76%～90%,相对标准偏差为2.8%～7.6%;T-2和HT-2毒素的检出限(S/N=3)分别为0.001、0.002 mg/kg.     

高效液相色谱-三重四极杆串联质谱测定谷物中T-2毒素和HT-2毒素

建立了快速分析谷物样品中T-2毒素和HT-2毒素的高效液相色谱-三重四极杆串联质谱( HPLC-MS/MS)分析方法.样品经乙腈-水(80:20,V/V)混合溶剂提取,免疫亲和柱净化后,采用HPLC-MS/MS测定.T-2毒素和HT-2毒素的检测线性范围均为0.20 ～20.00 μg/kg,定量下限为0.20 μg/...     

多组分免疫亲和柱净化/超高效液相色谱-串联质谱检测水产饲料中的黄曲霉毒素

建立了多组分免疫亲和柱净化/超高效液相色谱-串联质谱(UPLC-MS/MS)测定水产饲料中黄曲霉毒素AFB_1、AFB_2、AFG_1及AFG_2含量的方法。饲料样品用80%乙腈水超声提取后,经多组分免疫亲和柱净化,采用UPLC-MS/MS测定,外标法定量。以0.1%甲酸-乙腈为流动相,梯度洗脱分离,电喷雾正离子多反应监测模式检测。结果表明,AFB_1、AFG_1和AFB_2、AFG_2分别在2.25～22.5 ng/mL和0.75～7.5 ng/mL质量浓度范围内呈良好线性,相关系数大于0.997;AFB_1、AFG_1的定量下限均为0.7μg/kg,AFB_2、AFG_2的定量下限均为0.2μg/kg。AFB_1、AFG_1在1.5μg/kg,AFB_2、AFG_2在0.5μg/kg加标水平下的回收率为78.7%～85.5%,日内相对标准偏差(RSD)为6.0%～6.5%,日间RSD为6.6%～7.0%。该法操作简单,耗时少,重复性好,灵敏度高,适用于水产饲料中黄曲霉毒素的测定。     

电化学衍生-高效液相色谱和荧光光度法检测花生酱中的黄曲霉毒素

建立了免疫亲和柱净化-柱后电化学衍生-高效液相色谱结合荧光光度法检测花生酱中4种黄曲霉毒素(B1、B2、G1和G2)的方法。样品经过体积分数为60%的甲醇提取,通过免疫亲和柱净化后,以KobraCell装置柱后衍生,高效液相色谱法分离定量。黄曲霉毒素B1、B2、G1和G2能达到完全的基线分离,检测限分别为0.5、0.15、0.5和0.15μg/kg,线性相关系数0.999,回收率可达74.2%～96.5%,相对标准偏差低于11%。该方法能够满足花生酱中黄曲霉毒素检测的需要。     

免疫亲和柱净化-光化学柱后衍生-高效液相色谱法测定柏子仁中的黄曲霉毒素

采用免疫亲和柱净化-光化学柱后衍生-高效液相色谱法测定中药材柏子仁中的黄曲霉毒素G_2、G_1、B_2和B_1。样品经甲醇(7+3)溶液提取,提取液经免疫亲和柱净化,用甲醇洗脱,洗脱液经黄曲霉毒素专用C18色谱柱分离,以甲醇(45+55)溶液为流动相进行洗脱,柱后光化学衍生波长为254nm,荧光检测器的激发波长为365nm,发射波长为440nm。黄曲霉毒素G2、B2的线性范围均为0.125~5.0μg·L~(-1),黄曲霉毒素G_1、B_1的线性范围均为0.50~20μg·L~(-1),检出限(3S/N)在0.012~0.047μg·L~(-1)之间。加标回收率81.4%~105%之间,测定值的相对标准偏差(n=6)在1.6%~6.9%之间。     

莱克多巴胺、沙丁胺醇与克伦特罗三合一免疫亲和柱的制备及应用

将莱克多巴胺抗体和克伦特罗抗体偶联到溴化氰活化的琼脂糖凝胶上,制成免疫亲和柱,对其柱性能进行测试,并优化了使用条件,结合高效液相色谱-串联质谱对实际饲料样品进行检测。结果表明:该免疫亲和柱对莱克多巴胺、沙丁胺醇、克伦特罗的柱容量依次为49,27,24 ng/mL胶,保质期为5个月,最佳洗脱液为甲醇,对3种物质的回收率为78.9%~96.5%,RSD均小于1.5%,检出限为0.1~1 ng/g。该法可同时检测饲料中3种瘦肉精的含量。     

高效液相色谱法对农产品中黄曲霉毒素的测定研究

采用免疫亲和方法进行样品前处理,用甲醇-乙腈-水三元流动相体系分离黄曲霉毒素,氯化汞溶液在线衍生,荧光检测器检测,建立了新型的高效液相色谱柱后衍生测定黄曲霉毒素(B1、B2、G1、G2、M1)的方法。该方法在13 min内完成测定,线性关系良好,5种黄曲霉毒素的线性相关系数r值均大于0.999。方法成功应用于花生、花生制品、大米、玉米等农产品。对样品进行不同水平的加标回收实验,回收率为83%~100%,相对标准偏差1.51%~4.98%(n=7),B1检出限(S/N=3)和定量下限(S/N=10)分别达到了0.05μg/kg和0.17μg/kg。     

免疫亲和柱净化-柱后光化学衍生-高效液相色谱法同时检测粮谷中的黄曲霉毒素、玉米赤霉烯酮和赭曲霉毒素A

建立了同时检测粮谷中黄曲霉毒素(B1、B2、G1和G2)、玉米赤霉烯酮和赭曲霉毒素A的免疫亲和柱净化-柱后光化学衍生-高效液相色谱方法。样品经过甲醇-水(体积比为80∶20)提取,通过免疫亲和柱富集和净化,采用Waters Nova-Pak色谱柱(3.9 mm i.d.×150 mm,4 μm),以甲醇、乙腈和1%的磷酸溶液为流动相,梯度洗脱,柱后光化学衍生、改变波长荧光检测。黄曲霉毒素(B1、B2、G1和G2)、玉米赤霉烯酮和赭曲霉毒素A检出限分别为0.24,4.0和0.5 μg/kg,标准曲线的线性范围分别为0.24~6.0,4.0~100.0和0.5~40.0 μg/L;在小麦、玉米、黑麦样品中,平均加标回收率为70.8% ~94.0%,相对标准偏差为2.79% ~9.38%。     

超声萃取-免疫亲和柱净化-柱后光化学衍生高效液相色谱法同时测定蜂房药材中4种黄曲霉毒素

建立超声萃取-免疫亲和柱净化-柱后光化学衍生高效液相色谱同时测定蜂房药材中黄曲霉毒素B1、黄曲霉毒素B2、黄曲霉毒素G1、黄曲霉毒素G2含量的分析方法。样品经粉碎，过孔径为120μm筛后，采用70%甲醇溶液超声处理30 min，经免疫亲和柱净化、高效液相色谱分离、光化学柱后衍生，通过荧光检测器测定4种黄曲霉毒素的含量。黄曲霉毒素B1的线性范围为0.010 4～0.052 0 ng，相关系数为0.999 9；黄曲霉毒素B2的线性范围为0.003 8～0.019 0 ng，相关系数为0.999 8；黄曲霉毒素G1的线性范围为0.010 8～0.054 0 ng，相关系数为0.999 8；黄曲霉毒素G2的线性范围为0.003 8～0.019 0 ng，相关系数为0.999 8。4种黄曲霉毒素检出限分别为0.42、0.15、0.43、0.15μg/kg，测定结果的相对标准偏差不大于2.5%(n=6)，样品加标回收率为92.9%～96.9%。该方法操作简便，灵敏度高，可用于蜂房中黄曲霉毒素含量的测定。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Carbon black and propylene oxidation over Ru/CoxMgyAl2Oz catalysts

The effects of Co_xMg_yAl₂O_z mixed oxides composition and ruthenium addition on the oxidation of propylene and carbon black (CB) were investigated. Different reactive cobalt and ruthenium oxide species were formed following calcination at 600 °C. The addition of ruthenium was beneficial for the CB oxidation under “loose contact” conditions and for propylene oxidation when the cobalt content was intermediate to low. The calculated activation energy for CB oxidation was decreased from 151 kJ mol⁻¹ for the uncatalyzed reaction to 111 kJ mol⁻¹ over the best catalyst.