沉淀法回收生物油高温馏分中的酚类物质

为了研究金属离子沉淀法对生物油高温馏分中酚类物质的回收,提高生物油中化学物质的利用率,利用气相色谱-质谱联用仪(GC-MS)从NaOH试剂浓度、反应温度和反应时间三个方面研究了镁离子对生物油中酚类物质的回收效果。结果表明,镁离子与酚类物质形成了不溶物,而且不同浓度的氢氧化钠溶液(1.0-4.0 mol/L)、不同的反应温度(25-85℃)以及不同的反应时间(5-35 min)对实验结果有着不同程度的影响。结果表明,在反应温度为25℃、氢氧化钠浓度为2.5mol/L,反应时间在20 min时为最佳反应条件。在此条件下,对生物油高温馏分中对乙基苯酚的回收率可达34.97%。     

蒸馏温度对核桃壳生物油馏分组分分布的影响

通过改变蒸馏温度对生物油进行常压蒸馏并将馏分分为油水两相，研究了馏分的组分分布变化。结果表明，在120-300℃随着蒸馏温度的升高，生物油馏出率不断增加；蒸馏温度低于240℃的油相馏分中萘、甲苯等芳烃类化合物和乙酸等羧酸类化合物明显富集，以120℃油相馏分为例，芳烃类和羧酸类化合物的相对含量是生物油原油的13.86倍和3.15倍；当蒸馏温度高于240℃时苯酚、愈创木酚等酚类化合物大量馏出，使得油相馏分的产率明显增加；同时，所获水相馏分中的水分含量皆高于60%，水分的富集效果明显；在馏分中检测到了2-乙基乙酸丁酯和环戊酮等原油中未检测到的组分并且馏分中水分总量高于生物油原油，这些都表明生物油在蒸馏过程中发生了酯化、缩聚等化学反应。通过对油相馏分的组分分布进行分析，发现改变蒸馏温度可以有效富集生物油中的高价值化合物，如苯酚、愈创木酚、4-甲基愈创木酚、4-乙基愈创木酚和4-丙基愈创木酚的相对含量在300℃的油相馏分中分别比生物油提高了109%、160%、84%、53%和444%。     

基于不同萃取剂的生物油常压蒸馏研究

选用乙酸乙酯、二氯甲烷、乙醚和甲苯四种溶剂,分别与生物油按一定质量比混合萃取。将萃取相蒸馏得到的四种油相层与原始生物油进行对比,研究不同萃取剂对生物油萃取-蒸馏后各馏分的产率、水分及高附加值酚类组分变化的影响。结果表明,经萃取-蒸馏后,生物油残渣比例减少,水分含量降低。在四种溶剂中,甲苯萃取率较低,蒸馏后酚类绝对峰面积较小;乙酸乙酯和乙醚萃取效率较高,但两者萃取相蒸馏后酚类含量低;二氯甲烷萃取酚类能力强,其馏分中愈创木酚及其衍生物相对含量为34.11%,比生物油高出15.52%,富集程度高,更有利于后续进一步提纯愈创木酚及其衍生物等高附加值化学品。     

木屑微波辐照裂解制备生物油工艺及产物分析

利用微波技术,以离子液体为微波吸收介质,对木屑进行低温裂解制取生物油,裂解获得的液体产物采用超临界CO2萃取技术将离子液体进行分离. 对原料与吸收剂离子液体的比例、反应温度和反应时间进行了研究. 结果表明,微波裂解最佳的工艺条件为: 原料木屑与吸收剂离子液体质量比为3: 4,反应时间30 min,反应温度473 K,生物油收率21.22%. 反应获得的生物油的组成采用FTIR, GCMS测试技术进行了分析,并采用氧气氛下的TGA曲线分析评价其燃烧性. 结果表明,生物油的主要成分是带有含氧官能团的苯酚类、醛类、酮类等芳香族环状化合物. TGA结果表明,生物油具有较好的燃烧性能.     

玉米秸秆催化液化制备生物油实验研究

以玉米秸秆为原料,添加分子筛催化剂在体积为500 mL的高温高压反应釜中进行催化液化制备生物油实验研究。选取反应温度、催化剂含量和反应时间三个主要因素为变量,探究其对玉米秸秆催化液化产物分布的影响。利用气相色谱-质谱联用仪(GC-MS)和傅里叶红外光谱仪(FT-IR)对玉米秸秆生物油的成分和官能团结构进行分析。结果表明,玉米秸秆的最佳催化液化条件为,反应温度为340 ℃,玉米秸秆15 g,FeHZSM-5催化剂含量为6.67%,反应时间为30 min。在此条件下,生物油产率为28.03%,催化液化整体转化率为81.73%。生物油的主要成分为酚类和长链酯类,生物油的热值达30.08 MJ/kg。     

麦草碱木质素的微波辅助液化降解

研究了微波辅助条件下液化剂、催化剂、反应温度和反应时间对麦草碱木质素进行液化降解制备生物油收率的影响,并利用红外光谱(FT-IR)、气相色谱质谱联用仪(GC-MS)和核磁共振氢谱(1H-NMR)对产物进行表征。结果表明,微波辅助下以甲醇为液化剂,硫酸铁为催化剂液化降解碱木质素可以显著缩短液化反应时间,在160℃相对较低液化温度下反应5 min,生物油的收率达到55.22%。液化降解后的木质素残渣结构变化少,表明木质素降解产物的重新聚合的几率低,碱木质素反应原料可以回收再利用以提高原料利用率。生物油主要为单酚类物质,其中,S型、G型和H型单体的含量分别为57.72%、25.28%和8.98%。核磁共振氢谱中β-O-4键和C-C键质子峰的存在说明生物油中含有部分的二聚体和低聚体酚类化合物。     

水稻秸秆在亚/超临界乙醇中的液化实验研究

在间歇式高压反应釜中采用乙醇为溶剂在亚/超临界状态下对水稻秸秆进行液化实验研究，考察了反应温度、稻秆/乙醇比及停留时间对稻秆液化的影响，确定了反应温度325 ℃、稻秆与乙醇比为1.0/10.0（g/mL）、反应时间60 min为最佳液化条件。在此条件下，稻秆转化率为78.32%，液化油收率达55.03%；通过GC-MS对液化油进行分析，结果表明，生物油的主要成分是酚类和酯类，占总体的50%左右。液化油的热值为28.95 MJ/kg，运动黏度为5.63 mm²/s，水分含量为2.2%。     

固体酸催化烯烃改性生物油酚类化合物研究

选取生物油中含量较高的愈创木酚、儿茶酚和苯酚为酚类模型化合物,以蒙脱土K-10负载的Cs2.5H0.5PW12O40为固体超强酸催化剂,苯酚/1-辛烯烷基化反应为探针,考察了催化剂负载量,反应温度及物料摩尔比等因素对酚类烷基化反应的影响.结果表明,在60～100℃范围内,30%Cs2.5H0.5PW12O40/K-10对苯酚烷基化反应具有很好的催化活性和选择性,原料摩尔比为1时苯酚氧烷基化产物的选择性最好.愈创木酚中甲氧基的位阻效应使其转化率在相同条件下比苯酚低很多,相应氧烷基化产物的选择性也很低.儿茶酚与1-辛烯反应主要生成单羟基氧烷基化产物,100℃时选择性仍高达96%.升高温度有利于烷基化改性反应的进行,但产物中氧烷基化产物的选择性随着温度升高而降低.     

Ni-Cu-Ru/HZSM-5催化木质素生物油加氢脱氧制芳香烃的研究（英文）

木质素所得生物油（LDB）成分相对复杂对其后续利用产生巨大挑战。本研究以LDB为原料，在超临界乙醇条件下（320℃，14 MPa），以NaOH和负载金属（Ni、Cu和Ru）共同改性的HZSM-5为催化剂制备富含芳香烃的生物油。结果表明，脱硅处理后负载Ni、Cu和Ru三种金属制得的Ni-Cu-Ru/DeHZSM-5催化剂表现出最佳的催化活性，其中，提质油（UBO）中芳香烃的相对含量达到28.95%。此外，结合GC-MS分析结果，提出了愈创木酚、丁香酚和甲基愈创木酚潜在的加氢反应路径。LDB在Ni-Cu-Ru/DeHZSM-5的催化加氢作用下，提质生物油（UBO）的收率可达到80.40%，能量回收率达到96.32%。在催化加氢过程中主要发生了脱甲氧基化反应和脱水反应。相比于LBD,UBO的热值提高了19.80%，达到35.22 MJ/kg，且其含水量、黏度和酸值等性能均有显著改善。具有微介孔结构及Ni、Cu和Ru负载共同修饰的Ni-CuRu/DeHZSM-5催化剂有利于提升芳香烃的收率。     

生物油酸性组分分离精制研究

生物油因水分含量高和呈酸性未能作为高品位能源直接规模化应用。利用分子蒸馏技术将生物油水分与酸性组分作为整体对象进行分离,既得到生物油酸性组分富集馏分,又获得了水分含量低、酸性较弱与热值较高的精制生物油Ⅰ（蒸馏重质馏分）与精制生物油Ⅱ（常温冷凝馏分）。同时,具体考察了精制前后生物油的pH值、热值和水分等参数的变化规律。研究表明,生物油的水分与酸性组分得到有效分离,精制生物油Ⅰ和Ⅱ的低级羧酸含量从原始生物油的18.85%分别降低至0.96%和2.2%     

皂化P204微乳体系萃取大豆蛋白的研究

研究了NaOH皂化P204/正辛烷微乳体系萃取大豆蛋白的机理和工艺,考察了大豆加入量、P204的浓度、NaOH的浓度、萃取时间、水相pH值及离子强度等对大豆蛋白萃取率的影响。实验结果表明,该微乳体系萃取大豆蛋白的优化工艺条件为:大豆粉与微乳液的质量体积比1∶10,P204在油相中浓度0.8 mol/L,NaOH的浓度1.25 mol/L,萃取时间15 min,外水相pH值5,萃取率可达88.48%。通过调节水相pH和离子强度可实现大豆蛋白的萃取和反萃取。     

木槿叶中混合氨基酸的提取工艺研究

以浓盐酸和乙醇溶液为提取剂,分别通过加热回流和超声波组织破碎法提取了木槿叶中的混合氨基酸,确定了氨基酸提取的最佳工艺条件。结果表明,用盐酸回流提取,盐酸与木槿干粉的液料比为25∶1,盐酸浓度6 mol/L,100℃下回流提取5 h,提取3次,氨基酸的提取效果最佳,提取率可达16.76%,产品收率可达8.6%。用80%乙醇溶液,室温下超声波提取30 min,提取3次,提取效果最好,提取率可达17.42%,产品收率可达8.93%。     

萃取Fe3+和氨水-乙醇反萃沉淀法制备α-Fe2O3

以磷酸二异辛基酯(P204)为萃取剂,CCl4为溶剂,从Fe(NO3)2水溶液中萃取铁离子,以氨的乙醇溶液反萃含铁的有机相,通过优化控制相间传质过程,获得了Fe(OH)3前驱体,经煅烧后得α-Fe2O3粉体,采用TEM、FTIR、XRD等测试技术对α-Fe2O3进行表征。 研究表明,在油水相比为1∶1,水相c(Fe3+)=0.10 mol/L(pH=3.0)、油相P204为V(P204)∶V(CCl4)=1∶3、平衡时间为20 min,Fe3+萃取率达98.44%;反萃取溶液V(氨水)∶V(乙醇)=1∶7、陈化温度约10.0 ℃,制备纳米α-Fe2O3的煅烧温度为600 ℃较宜。     

Protease-catalyzed Synthesis of Bz-Arg-Gly-Asp-OMe in Full Aqueous Medium

Synthesis of N-benzoyl-argininylglycylasparagine methyl ester(Bz-Arg-Gly-Asp-OMe),a precursor tripeptide of Arg-Gly-Asp)was catalyzed by papain under kinetic control,at alkaline pH,in a full aqueous medium.The substrates were N-benzoyl-argininylglycine ethyl ester and asparagine dimethyl ester.An aqueous solution of 0.1 mol/L KCl/NaOH containing 8 mmol/L EDTA and 2 mmol/L DTT was selected as the reaction medium.The synthesized hydrophilic tripeptide was soluble in the reaction medium during the reaction process,however,the secondary hydro-lysis of the tripeptide product was not considerable.The effects of different factors,including water content,temperature,reaction time,and molar ratio of the substrates,on the yield of Bz-Arg-Gly-Asp-OMe were examined.The optimal reaction conditions were 0.05 mol/L Bz-Arg-Gly-OEt and 0.15 mol/L Asp(-OMe)2·HCl in 0.1 mol/L KCl/NaOH solution(pH 8.5),at 40 ℃,and a reaction time of 60 min,with a maximum conversion yield of 62.4%.     

Solidified floating organic drop microextraction combined with high performance liquid chromatography for the determination of carbamazepine in human plasma and urine samples

Solidified floating organic drop microextraction (SFODME) in combination with high performance liquid chromatography was used for separation/preconcentration and determination of carbamazepine (CBZ) in human plasma and urine samples. Parameters that affect the extraction efficiency such as the type and volume of extraction solvent, ionic strength, sodium hydroxide concentration, stirring rate, sample volume and extraction time, were investigated and optimized. Under the optimum conditions (extraction solvent, 40 μL of 1-undecanol; sodium hydroxide concentration, 1 mol/L; temperature, 50 ℃; stirring speed, 400 r/min; sample volume, 8 mL; sodium chloride concentration, 3% (w/v) and extraction time, 60 min) the calibration curve was found to be linear in the mass concentration range of 0.4-700.0 μg/L. The limit of detection (LOD) was 0.1 μg/L and the relative standard deviation (RSD) for six replicate extraction and determination of carbamazepine at 100 μg/L level was found to be 4.1%. The method was successfully applied to the determination of CBZ in human plasma and urine samples.     

负载型Ni-Co-P/CNFs催化剂的制备及释氢性能

以纳米碳纤维(CNFs)为基体材料,采用化学镀法在CNFs表面沉积了Ni-Co-P催化剂。研究了催化剂用量,硼氢化钠、氢氧化钠浓度,温度等对碱性硼氢化钠溶液水解释氢的影响。电感耦合等离子体原子发射光谱法(ICP-AES)测试得出负载型Ni-Co-P催化剂含镍13.30%(质量分数,下同)、钴82.25%、磷4.45%。硼氢化钠水解释氢实验结果表明,产氢速率与催化剂用量呈线性关系。当温度为45 ℃、催化剂浓度为7.5 g/L、氢氧化钠浓度为5%、硼氢化钠浓度为2.5%时,氢气释放速率达到最大值18.044 L/(g·min)。通过对负载型催化剂Ni-Co-P/CNFs催化碱性硼氢化钠溶液释放氢气动力学研究表明,该催化剂的活化能E_a为51.57 kJ/mol。     

Lead removal and recovery from battery industry wastewaters by soluble starch xanthate

Treatment, removal and recovery of lead (3 mg/L) from battery industry wastewaters have been investigated utilising a chemical precipitation process with soluble starch xanthate (SX) at pH 5-6. A reactant ratio, i.e., SX/Pb(II) = 6 mol/mol, a reaction time of 15 min., the addition of 15 mg/L of a cationic polyelectrolyte and a final filtration gave residual lead concentrations in the liquid phase less than 0.2 mg/L, well below the maximum limit established by the EU Directive. Lead was extracted from the obtained sludge by oxidation with sodium hypochlorite or hydrogen peroxide solutions. The amounts of oxidant needed were quantified as 13.5 mol NaClO/mol Pb and one order of magnitude larger, for H2O2, the latter due to the competitive disproportion reaction of the oxidant. The metal extraction was quantitative using sodium hypochlorite; when hydrogen peroxide was used, the formation of insoluble PbSO4 (Anglesite) gave a 80% metal extraction. In both cases molar ratios between sulphate and lead ions in the extracted solutions were in the range 2.1-2.2, in agreement with the stoichiometries of the reactions. Lead can be quantitatively recovered from the extracted (NaClO) solutions, for reuse, after a chemical precipitation process with 1M NaOH at pH 9-9.5, in the form of hydrocerussite [Pb3(CO3)2(OH)2].     

聚吡咯-离子液体固相微萃取涂层的电沉积制备及其在苯类化合物气相色谱检测中的应用

在0.1 mol/L吡咯-0.1 mol/L对甲苯磺酸-4g/L 1-丁基-3-甲基咪唑四氟硼酸盐水溶液中,通过循环伏安法在不锈钢丝表面制备了新型聚吡咯-离子液体(Polypyrrole-ionic liquid,PPY-IL)涂层.此涂层呈菜花状结构,粒度比PPY小.以5种苯类化合物(即1,2-二甲苯、1,2,4-三氯苯、1,2-二氯苯、1,2,4-三甲苯和1,3,5-三甲苯)为目标分析物,对所得萃取头性能进行了考察.在优化的实验条件(萃取温度:50℃；萃取时间:40 min;搅拌速率:600 r/min; NaCl浓度:0.2 g/mL)下,对这些苯类化合物进行顶空固相微萃取-气相色谱检测,其线性范围为0.6～800 μg/L,单根多次萃取的相对标准偏差小于4.5％(n=5),多根萃取头平行萃取的相对标准偏差为4.5％～12.4％(n=5).PPY-IL萃取头有良好的稳定性,在使用150次后萃取性能仅有很小的变化；在温度升至290℃时不分解.与聚吡咯和聚二甲基硅氧烷萃取头相比,本萃取头对这些苯类化合物有更高的萃取能力.     

Combination of corona discharge ion mobility spectrometry with a novel reagent gas and two immiscible organic solvent liquid-liquid-liquid microextraction for analysis of clomipramine in biological samples

A novel and sensitive method based on combination of two immiscible organic solvents hollow fiber-based liquid-liquid-liquid microextraction and corona discharge ion mobility spectrometry (HF-LLLME-CD-IMS) was employed for the analysis of clomipramine in human urine and plasma. The effect of formic, acetic and propionic acid as the reagent gas (dopant) on the corona discharge ion mobility signal was investigated. The influence of dopant amount was also studied. Optimum mass flow rates of the dopants were 3.7, 1.1 and 1.0 μmol min(-1) for formic, acetic and propionic acid, respectively. Experimental parameters influencing the extraction efficiency of HF-LLLME, such as NaOH concentration as donor solution, ionic strength of the sample, stirring rate, and extraction time were investigated and optimized. Under the optimum conditions, analytical parameters such as linearity, precision and limit of detection were also evaluated. The linear dynamic range was from 1 to 100 μg L(-1) (r(2)=0.9980) and the limit of detection was 0.35 μg L(-1). Intra- and inter-day precisions were satisfactory with a relative standard deviation (RSD) of 5.9 and 6.7%, respectively. The proposed method was satisfactorily applied for the determination of clomipramine in human plasma and urine.