单晶Cu(001)薄膜塑性变形的分子动力学模拟

使用分子动力学方法,模拟研究了单晶Cu(001)薄膜在双向等轴拉伸应变下的塑性变形行为.当应变超过一定值时,样品通过产生位错、层错及孪晶而发生塑性变形.当应变相对较低时,不全位错首先在薄膜表面形核并在密排面上滑移,留下堆积层错;当应变增加时,位错在表面与内部同时成核生长,层错数量也随之增加.分析了相邻滑移面上的位错之间相互作用形成孪晶的微观过程.材料内部形成大量堆积层错及孪晶后,较大孪晶的密排面上的原子也会发生滑移,形成孪晶内部的层错结构以释放残余应力.     

晶界对纳米多晶铝中冲击波阵面结构影响的分子动力学研究

用分子动力学方法研究了纳米多晶铝在冲击加载下的冲击波阵面结构及塑性变形机理.模拟研究结果表明:在弹性先驱波之后,是晶界间滑移和变形主导了前期的塑性变形机理;然后是不全位错在界面上成核和向晶粒内传播,然后在晶粒内形成堆垛层错、孪晶和全位错的过程主导了后期的塑性变形机理.冲击波阵面扫过之后留下的结构特征是堆垛层错和孪晶留在晶粒内,大部分全位错则湮灭于对面晶界.这个由两阶段塑性变形过程导致的时序性塑性波阵面结构是过去未见报道过的. 关键词： 晶界 塑性变形 冲击波阵面 分子动力学     

强流脉冲电子束作用下金属纯Cu的微观结构状态——变形结构

为了研究金属的超快变形机理,利用强流脉冲电子束(HCPEB)技术对多晶纯Cu进行了辐照处理,并利用透射电子显微镜对HCPEB诱发的表面微结构进行了表征.实验结果表明,HCPEB轰击多晶纯Cu后,在轰击表层诱发了幅值极大的应力和极高的应变速率.1次HCPEB轰击材料表层的变形结构以交滑移形成的位错胞和位错缠结结构为主;多次轰击后平行的位错墙和孪晶是该区域的主要变形结构特征;原子面的扩散乃至位错攀移可在晶界和孪晶界上形成台阶结构.根据各自区域的变形结构特征,对相应的变形机理进行了探讨. 关键词： 强流脉冲电子束 多晶Cu 变形结构 孪晶     

激光冲击对E690高强钢激光熔覆修复微观组织的影响

为研究激光冲击对E690高强钢激光熔覆修复层微观组织的影响,选用专用金属粉末对E690高强钢试样预制凹坑进行激光熔覆修复,并使用脉冲激光对激光熔覆层进行冲击强化处理,同时采用扫描电镜、透射电镜和X射线应力分析仪分别对激光冲击前后激光熔覆层的微观组织和表面残余应力进行检测。结果表明:激光熔覆修复后,激光熔覆层组织为等轴晶,熔覆层与E690高强钢基体之间冶金结合良好,其表面残余应力为均匀分布的压应力。经激光冲击后,激光熔覆层截面晶粒得到细化,并观察到大量的形变孪晶,互相平行的孪晶界分割熔覆层粗大晶粒,在激光熔覆层的晶粒细化过程中发挥着重要作用;试样表层位错在{110}滑移面上发生交滑移,在晶界周围形成了位错缠结。经激光冲击后,激光熔覆层冲击区域表面残余压应力数值相较于冲击前提升了1.1倍。     

多晶银纳米线拉伸变形的分子动力学模拟研究

纳米尺度金属Ag以其独特的导电和导热性,广泛应用于微电子、光电子学、催化等领域,特别是在纳米微电极和纳米器件方面的应用.本文采用分子动力学方法模拟了不同晶粒尺寸下多晶银纳米线的拉伸变形行为,详细分析了晶粒尺寸对多晶银纳米线弹性模量、屈服强度、塑性变形机理的影响.发现当晶粒尺寸小于13.49 nm时,多晶Ag纳米线呈现软化现象,出现反Hall-Petch关系,此时的塑性变形机理主要以晶界滑移、晶粒转动为主,变形后期形成五重孪晶;当晶粒尺寸大于13.49 nm时,塑性变形以位错滑移为主,变形后期产生大量的孪晶组织.     

强流脉冲电子束诱发纯钛表面的微观结构及应力状态

利用强流脉冲电子束(HCPEB)装置对金属纯钛进行轰击,采用X射线衍射,扫描电子显微镜及透射电子显微镜技术详细分析了轰击样品表层的结构和缺陷. X射线衍射分析表明, HCPEB能够在材料表层诱发幅值为 GPa量级的压应力,并在(100), (102)和(103)晶面出现择优取向.表层微观结构的观察表明: HCPEB轰击后材料表层发生了马氏体相变,形成了大量的片状马氏体组织; 此外, HCPEB轰击还在辐照表面诱发了强烈的塑性变形,一次轰击后,晶粒内部的塑性变形以(100)晶面的位错滑移为主,位错密度显著提高;多次轰击后,样品变形结构发生变化,变形孪晶的数量明显增多. 这些变形微结构不仅影响表层的织构演化行为,而且还能细化晶粒,进而提高材料表面硬度, 为HCPEB技术进行纯钛表面强化提供了一条有效的途径.     

纳米单晶与多晶铜薄膜力学行为的数值模拟研究

通过对不同温度下单晶薄膜的拉伸性能的分子动力学模拟，从微观角度揭示了温度效应对材料性能的影响. 结果表明温度效应对材料的变形机理影响很大.0K温度下由于缺乏热激活软化的影响, 粒子运动所受到的阻碍较大, 薄膜的强度较高, 塑性变形主要来自于粒子的短程滑移.温度升高，粒子的热运动加剧，屈服强度降低, 塑性变形将主要来自于大范围的位错长程扩展.多晶薄膜的模拟结果表明, 虽然其晶粒形状较为特殊, 但是它仍然遵循反Hall-Petch关系.在模拟过程中，侧向应力最大值比拉伸方向应力的最大值滞后出现.位错只会从晶界产生并向晶粒内部传播，晶粒间界滑移是多晶薄膜塑性变形的主要来源. 关键词： 纳米薄膜 变形机理 温度效应 分子动力学     

晶粒尺寸对纳米多晶铁变形机制影响的模拟研究

利用分子动力学模拟方法研究了拉伸荷载作用下晶粒尺寸对纳米多晶铁变形机制的影响.研究结果表明杨氏模量随着晶粒尺寸的减小而减小.当晶粒尺寸小于15.50 nm时,纳米多晶铁的峰值应力和晶粒尺寸之间遵循反常的Hall-Petch关系,此时晶粒旋转和晶界迁移是其塑性变形的主要变形机制;随着晶粒尺寸的增大,变形孪晶和位错滑移在其塑性变形过程中逐渐占据主导地位.裂纹的形成是导致大晶粒尺寸模型力学性能降低的主要因素.纳米多晶铁在塑性变形中会出现孪晶界的迁移和退孪晶现象.此外还研究了温度对纳米多晶铁变形机制的影响.     

体心立方Ta的广义面错能及在Ⅱ型裂纹尖端初始塑性研究中的应用

基于嵌入原子势考察体心立方(bcc)金属Ta的广义层错能和广义孪晶能并获得广义层错能和广义孪晶能曲线. 研究表明,bcc Ta的广义层错能曲线与面心立方金属的广义层错能曲线有明显差异,Ta的广义层错能曲线不存在明显的能量极小值,位错主要以全位错的形式发射. 不同原子厚度的广义孪晶能曲线表明4个原子层的孪晶能曲线开始出现亚稳定的能量极小值,5个原子层的孪晶能曲线出现稳定的能量极小值. 为进一步验证广义层错能和广义孪晶能曲线揭示的塑性变形机理,采用准连续介质力学多尺度方法研究Ⅱ型裂纹尖端的初始塑性变形过程. 关键词： 广义层错能 广义孪晶能 体心立方金属钽 Ⅱ型裂纹     

强流脉冲电子束作用下金属锆的微观结构与应力状态

利用强流脉冲电子束 (HCPEB) 技术对金属纯锆进行表面处理, 采用X射线衍射, 扫描电子显微镜及透射电子显微镜详细分析了辐照诱发的表层微观结构和缺陷. X射线分析结果表明, HCPEB辐照后在材料表层诱发幅值为GPa量级的压应力, 并形成{0002}, {1012}, {1120}及{1013}织构. 表层微观结构观察表明, 与其他金属材料不同, HCPEB辐照在材料表层诱发的熔坑数量极少, 多次轰击甚至几乎没有表面熔坑的形成. 此外, 在快速的加热和冷却状态下, 在表面熔化层形成大量的超细晶粒结构, 同时诱发马氏体相变和强烈的塑性变形. 1次HCPEB辐照后表层内形成的变形微结构以位错为主, 孪晶数量较少; 5 次辐照样品的位错密度迅速增高, 孪晶数量也显著增加; 10次辐照后样品中的变形微结构以变形孪晶为主, 且出现二次孪晶现象. 表层晶粒内部变形的晶体学特征不仅决定了表层的织构演化行为, 而且还起到细化晶粒的作用, 为纯锆及锆合金表面强化提供了一条有效的途径. 关键词： 强流脉冲电子束 纯锆 微观结构 应力状态     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.