Surface roughness and cutting forces modeling for optimization of machining condition in finish hard turning of AISI 52100 steel

An experimental investigation was conducted to analyze the effect of cutting parameters (cutting speed, feed rate and depth of cut) and workpiece hardness on surface roughness and cutting force components. The finish hard turning of AISI 52100 steel with coated Al₂O₃ + TiC mixed ceramic cutting tools was studied. The planning of experiment were based on Taguchi’s L₂₇ orthogonal array. The response table and analysis of variance (ANOVA) have allowed to check the validity of linear regression model and to determine the significant parameters affecting the surface roughness and cutting forces. The statistical analysis reveals that the feed rate, workpiece hardness and cutting speed have significant effects in reducing the surface roughness; whereas the depth of cut, workpiece hardness and feed rate are observed to have a statistically significant impact on the cutting force components than the cutting speed. Consequently, empirical models were developed to correlate the cutting parameters and workpiece hardness with surface roughness and cutting forces. The optimum machining conditions to produce the lowest surface roughness with minimal cutting force components under these experimental conditions were searched using desirability function approach for multiple response factors optimization. Finally, confirmation experiments were performed to verify the pertinence of the developed empirical models.     

高速铣削铝合金叶片表面质量的试验研究

使用硬质合金球头铣刀对铝合金叶轮叶片进行了高速铣削试验。研究了切削速度和进给量对加工表面粗糙度的影响。试验结果表明:在高速加工中,每齿进给量比铣削行距对加工表面质量的影响更大;提高切削速度和减少每齿进给量有利于降低加工表面粗糙度。但当切削速度超过某一范围后,进一步提高速度对降低表面粗糙度的作用并不明显;每齿进给量减小到一定范围后,表面粗糙度反而会有所增加;对于铝合金叶片曲面的加工,合理选择切削速度、进给量和行距可获得较低的表面粗糙度值和较高的加工效率。     

An experimental investigation on the machining characteristics of microscale end milling

This paper discusses an experimental approach to assess the machining characteristics in microscale end milling operation through a systematic experimentation procedure. Microchannels were machined on brass plates using a carbide end mill of 1?mm diameter to analyze the effect of chip load (feed per tooth) and cutting speed on the surface roughness, specific cutting pressure, and cutting forces during microend milling operation. The tangential and radial components of forces were analyzed with the help of a three-dimensional model using the force signals acquired through KISTLER dynamometer. Feed per tooth and the interaction of cutting speed and chip load were identified as the critical parameters affecting the surface roughness of microchannel. Applying the concept of elastic recovery on the side wall surface of microchannels, the minimum chip thickness during the above micromilling operation was evaluated as 0.97???m, and the result was validated by the drastic increase in specific cutting pressure and erratic behavior of cutting forces below a chip load of 1???m.     

Empirical models and optimal cutting parameters for cutting forces and surface roughness in hard milling of AISI H13 steel

In the present research, an attempt has been made to experimentally investigate the effects of cutting parameters on cutting forces and surface roughness in hard milling of AISI H13 steel with coated carbide tools. Based on Taguchi’s method, four-factor (cutting speed, feed, radial depth of cut, and axial depth of cut) four-level orthogonal experiments were employed. Three cutting force components and roughness of machined surface were measured, and then range analysis and analysis of variance (ANOVA) are performed. It is found that the axial depth of cut and the feed are the two dominant factors affecting the cutting forces. The optimal cutting parameters for minimal cutting forces and surface roughness in the range of this experiment under these experimental conditions are searched. Two empirical models for cutting forces and surface roughness are established, and ANOVA indicates that a linear model best fits the variation of cutting forces while a quadratic model best describes the variation of surface roughness. Surface roughness under some cutting parameters is less than 0.25 μm, which shows that finish hard milling is an alternative to grinding process in die and mold industry.     

Optimization techniques for machining operations: a retrospective research based on various mathematical models

Simulated annealing, genetic algorithm, and particle swarm optimization techniques have been used for exploring optimal machining parameters for single pass turning operation, multi-pass turning operation, and surface grinding operation. The behavior of optimization techniques are studied based on various mathematical models. The objective functions of the various mathematical models are distinctly different from each other. The most affecting machining parameters are considered as cutting speed, feed, and depth of cut. Physical constraints are speed, feed, depth of cut, power limitation, surface roughness, temperature, and cutting force.     

Performance studies of multilayer hard surface coatings (TiN/TiCN/Al2O3/TiN) of indexable carbide inserts in hard machining: Part-I (An experimental approach)

In recent years, hard machining using CBN and ceramic inserts became an emerging technology than traditional grinding and widely used manufacturing processes. However the relatively high cost factors associated with such tools has left a space to look for relatively low cost cutting tool materials to perform in an acceptable range. Multilayer coated carbide insert is the proposed alternative in the present study due to its low cost. Thus, an attempt has been made to have an extensive study on the machinability aspects such as flank wear, chip morphology, surface roughness in finish hard turning of AISI 4340 steel (HRC 47 ± 1) using multilayer coated carbide (TiN/TiCN/Al₂O₃/TiN) insert under dry environment. Parametric influences on turning forces are also analyzed. From the machinability study, abrasion and chipping are found to be the dominant wear mechanism in hard turning. Multilayer TiN coated carbide inserts produced better surface quality and within recommendable range of 1.6 μm i.e. comparable with cylindrical grinding. At extreme parametric conditions, the growth of tool wear was observed to be rapid thus surface quality affected adversely. The chip morphology study reveals a more favorable machining environment in dry machining using TiN coated carbide inserts. The cutting speed and feed are found to have the significant effect on the tool wear and surface roughness from ANOVA study. It is evident that, thrust force (Fy) is the largest component followed by tangential force (Fz) and the feed force (Fx) in finish hard turning. The observations yield the machining ability of multilayer TiN coated carbide inserts in hard turning of AISI 4340 steel even at higher cutting speeds.     

Some studies on hard turning of AISI 4340 steel using multilayer coated carbide tool

Hard turning with multilayer coated carbide tool has several benefits over grinding process such as, reduction of processing costs, increased productivities and improved material properties. The objective was to establish a correlation between cutting parameters such as cutting speed, feed rate and depth of cut with machining force, power, specific cutting force, tool wear and surface roughness on work piece. In the present study, performance of multilayer hard coatings (TiC/TiCN/Al₂O₃) on cemented carbide substrate using chemical vapor deposition (CVD) for machining of hardened AISI 4340 steel was evaluated. An attempt has been made to analyze the effects of process parameters on machinability aspects using Taguchi technique. Response surface plots are generated for the study of interaction effects of cutting conditions on machinability factors. The correlations were established by multiple linear regression models. The linear regression models were validated using confirmation tests. The analysis of the result revealed that, the optimal combination of low feed rate and low depth of cut with high cutting speed is beneficial for reducing machining force. Higher values of feed rates are necessary to minimize the specific cutting force. The machining power and cutting tool wear increases almost linearly with increase in cutting speed and feed rate. The combination of low feed rate and high cutting speed is necessary for minimizing the surface roughness. Abrasion was the principle wear mechanism observed at all the cutting conditions.     

Optimization of machining parameters using genetic algorithm and experimental validation for end-milling operations

Optimization of cutting parameters is valuable in terms of providing high precision and efficient machining. Optimization of machining parameters for milling is an important step to minimize the machining time and cutting force, increase productivity and tool life and obtain better surface finish. In this work a mathematical model has been developed based on both the material behavior and the machine dynamics to determine cutting force for milling operations. The system used for optimization is based on powerful artificial intelligence called genetic algorithms (GA). The machining time is considered as the objective function and constraints are tool life, limits of feed rate, depth of cut, cutting speed, surface roughness, cutting force and amplitude of vibrations while maintaining a constant material removal rate. The result of the work shows how a complex optimization problem is handled by a genetic algorithm and converges very quickly. Experimental end milling tests have been performed on mild steel to measure surface roughness, cutting force using milling tool dynamometer and vibration using a FFT (fast Fourier transform) analyzer for the optimized cutting parameters in a Universal milling machine using an HSS cutter. From the estimated surface roughness value of 0.71 μm, the optimal cutting parameters that have given a maximum material removal rate of 6.0×10³ mm³/min with less amplitude of vibration at the work piece support 1.66 μm maximum displacement. The good agreement between the GA cutting forces and measured cutting forces clearly demonstrates the accuracy and effectiveness of the model presented and program developed. The obtained results indicate that the optimized parameters are capable of machining the work piece more efficiently with better surface finish.     

Precision machining of an aluminum alloy piston reinforced with a cast iron insert

Bimetallic pistons consisting of aluminum alloy reinforced with a cast iron (CI) insert are used to reduce the weight and improve the wear resistance of pistons. A major problem with machining such bimetallic pistons is producing the desired shape with minimal cutting forces and without damaging the bonding registry. The objective of this paper is to determine the optimal cutting parameters (cutting speed, feed, and depth of cut) for turning bimetallic pistons. When machining, we wish to obtain optimal values of the cutting forces and a better surface integrity while maintaining the required surface finish. Experiments were conducted following Taguchi’s parameter design approach using a cubic boron nitride tool for the machining. The results indicate that the process parameters affected the mean and variance of the cutting force at the Al-CI interface of the piston. The Al-CI interface was examined using an ultrasonic piston bond tester after machining to assure the bond quality. The surface roughness of the components was measured with a surface roughness tester. A mathematical model was developed using the Systat 12.0 software package to establish the relationship between the input quantities (speed, feed, and depth of cut) and the output data (cutting force). The output data of the mathematical model were compared with the experimental results. The results from the Taguchi robust design concept were compared with the results obtained from a nonconventional Genetic Algorithm optimization technique.     

Experimental investigations on machinability aspects in finish hard turning of AISI 4340 steel using uncoated and multilayer coated carbide inserts

The present work deals with some machinability studies on flank wear, surface roughness, chip morphology and cutting forces in finish hard turning of AISI 4340 steel using uncoated and multilayer TiN and ZrCN coated carbide inserts at higher cutting speed range. The process has also been justified economically for its effective application in hard turning. Experimental results revealed that multilayer TiN/TiCN/Al₂O₃/TiN coated insert performed better than uncoated and TiN/TiCN/Al₂O₃/ZrCN coated carbide insert being steady growth of flank wear and surface roughness. The tool life for TiN and ZrCN coated carbide inserts was found to be approximately 19 min and 8 min at the extreme cutting conditions tested. Uncoated carbide insert used to cut hardened steel fractured prematurely. Abrasion, chipping and catastrophic failure are the principal wear mechanisms observed during machining. The turning forces (cutting force, thrust force and feed force) are observed to be lower using multilayer coated carbide insert in hard turning compared to uncoated carbide insert. From 1st and 2nd order regression model, 2nd order model explains about 98.3% and 86.3% of the variability of responses (flank wear and surface roughness) in predicting new observations compared to 1st order model and indicates the better fitting of the model with the data for multilayer TiN coated carbide insert. For ZrCN coated carbide insert, 2nd order flank wear model fits well compared to surface roughness model as observed from ANOVA study. The savings in machining costs using multilayer TiN coated insert is 93.4% compared to uncoated carbide and 40% to ZrCN coated carbide inserts respectively in hard machining taking flank wear criteria of 0.3 mm. This shows the economical feasibility of utilizing multilayer TiN coated carbide insert in finish hard turning.     

Comparative evaluations of machining performance during turning of 17-4 PH stainless steel under cryogenic and wet machining conditions

Productivity in machining of 17-4 PH stainless steel is adversely affected by the premature failure of tool and poor surface finish as a consequence of high cutting temperatures. Conventional cutting fluids not only create environmental and health problems but also fail to overcome the high cutting temperatures during machining. Cryogenic cooling is an environmentally clean cooling technology for attractive management of machining zone temperatures. The present study investigates the effect of cryogenic liquid nitrogen (LN₂ at ?196°C) on cutting temperatures, cutting forces (main cutting force, feed force), surface roughness, tool flank wear and chip morphology in turning of 17-4 PH stainless steel with AlTiN PVD-coated tungsten-coated carbide inserts and results were compared to wet machining. In overall, cryogenic machining reduces the cutting temperature, cutting forces, surface roughness and tool flank wear to a maximum of 73.4, 17.62, 44.29 and 55.55%, respectively. Improved chip breakability was found in cryogenic machining.     

Construction of a surface roughness prediction model for high speed machining

In manufacturing environment prediction of surface roughness is very important for product quality and production time. For this purpose, the finite element method and neural network is coupled to construct a surface roughness prediction model for high-speed machining. A finite element method based code is utilized to simulate the high-speed machining in which the cutting tool is incrementally advanced forward step by step during the cutting processes under various conditions of tool geometries (rake angle, edge radius) and cutting parameters (yielding strength, cutting speed, feed rate). The influences of the above cutting conditions on surface roughness variations are thus investigated. Moreover, the abductive neural networks are applied to synthesize the data sets obtained from the numerical calculations. Consequently, a quantitative prediction model is established for the relationship between the cutting variables and surface roughness in the process of high-speed machining. The surface roughness obtained from the calculations is compared with the experimental results conducted in the laboratory and with other research studies. Their agreements are quite well and the accuracy of the developed methodology may be verified accordingly. The simulation results also show that feed rate is the most important cutting variable dominating the surface roughness state.     

Surface roughness analysis of hardened steel after high-speed milling

The work refers to analysis of various factors affecting surface roughness after end milling of hardened steel in high-speed milling (HSM) conditions. Investigations of milling parameters (cutting speed v(c) , axial depth of cut a(p) ) and the process dynamics that influence machined surface roughness were presented, and a surface roughness model, including cutter displacements, was elaborated. The work also involved analysis of surface profile charts from the point of view of vibrations and cutting force components. The research showed that theoretic surface roughness resulting from the kinematic-geometric projection of cutting edge in the workpiece is significantly different from the reality. The dominant factor in the research was not feed per tooth f(z) (according to the theoretical model) but dynamical phenomena and feed per revolution f.     

Machinability aspects concerning micro-turning of PA66-GF30-reinforced polyamide

This paper aims to study the behavior of machining forces and machined surface finish when micro-turning PA66-GF30-reinforced polyamide with various tool materials under distinct cutting conditions. The performance of polycrystalline diamond (PCD), CVD diamond coated carbide and plain cemented carbide tools (K15-KF and K15) were investigated in addition to the influence of feed rate on cutting forces, surface roughness and chip formation. The results indicated that the radial force was the highest force component because of the reduction in the effective cutting edge angle. Moreover, the cutting force increased almost linearly with feed, whereas the feed and radial forces remained unaltered. The cutting tools possessing lower edge radius promoted lower surface finish and turning forces, i.e., the best results were provided by the PCD tool, followed by the uncoated carbide inserts and finally by the CVD diamond-coated carbide tool.     

An experimental analysis and measurement of process performances in machining of nimonic C-263 super alloy

Nimonic C-263 alloy is extensively used in the fields of aerospace, gas turbine blades, power generators and heat exchangers because of its unique properties. However, the machining of this alloy is difficult due to low thermal conductivity and work hardening characteristics. This paper presents the experimental investigation and analysis of the machining parameters while turning the nimonic C-263 alloy, using whisker reinforced ceramic inserts. The experiments were designed using Taguchi’s experimental design. The parameters considered for the experiments are cutting speed, feed rate and depth of cut. Process performance indicators, viz., the cutting force, tool wear and surface finish were measured. An empirical model has been created for predicting the cutting force, flank wear and surface roughness through response surface methodology (RSM). The desirability function approach has been used for multi response optimization. The influence of the different parameters and their interactions on the cutting force, flank wear and surface roughness are also studied in detail and presented in this study. Based on the cutting force, flank wear and surface roughness, optimized machining conditions were observed in the region of 210 m/min cutting speed and 0.05 mm/rev feed rate and 0.50 mm depth of cut. The results were confirmed by conducting further confirmation tests.     

Effect of machining parameters on surface roughness and tool wear for 7075 Al alloy SiC composite

In the present study, an attempt has been made to investigate the influence of cutting speed, depth of cut, and feed rate on surface roughness during machining of 7075 Al alloy and 10 wt.% SiC particulate metal-matrix composites. The experiments were conducted on a CNC Turning Machine using tungsten carbide and polycrystalline diamond (PCD) inserts. Surface roughness of 7075Al alloy with 10 wt.% SiC composite during machining by tungsten carbide tool was found to be lower in the feed range of 0.1 to 0.3 mm/rev and depth of cut (DOC) range of 0.5 to 1.5 mm as compared to surface roughness at other process parameters considered. Above cutting speed of 220 m/min surface roughness of SiC composite during machining by PCD tool was less as compared to surface roughness at other values of cutting speed considered. Wear of tungsten carbide and PCD inserts was analyzed using a metallurgical microscope and scanning electron microscope. Flanks wear of carbide tool increased by a factor of 2.4 with the increase of cutting speed from 180 to 240 m/min at a feed of 0.1 mm/rev and a DOC of 0.5 mm. On the other hand, flanks wear of PCD insert increased by only a factor of 1.3 with the increase of cutting speed from 180 to 240 m/min at feed of 0.1 mm/rev and DOC 0.5 mm.     

响应面法在高速加工切削参数优选中的应用

讨论了响应面法的原理及应用，结合回归统计建立了淬硬模具钢高速铣削表面粗糙度的经验公式，并分析了切削速度、进给率和轴向切削深度对表面粗糙度的影响规律，为高速加工切削参数的选择和表面质量的控制提供依据。     

Investigation of surface integrity in dry machining of Inconel 718

Machining of advanced aerospace materials have grown in the recent years although the diffucult-to-machine characteristics of alloys like titanium or nickel-based alloys cause higher cutting forces, rapid tool wear, and more heat generation. Therefore, machining with the use of cooling lubricants is usually carried out. To reduce the production costs and to make the processes environmentally safe, the goal is to move toward dry cutting by eliminating cutting fluids. This objective can be achieved by using coated tool, by increasing cutting speed, and by improving the product performance in term of surface integrity and product quality. The paper addresses the effects of cutting speed and feed on the surface integrity during dry machining of Inconel 718 alloy using coated tools. In particular, the influence of the cutting conditions on surface roughness, affected layer, microhardness, grain size, and microstructural alteration was investigated. Results show that cutting conditions have a significant effect on the parameters related to the surface integrity of the product affecting its overall performance.     

Effect of work material hardness and cutting parameters on performance of coated carbide tool when turning hardened steel: An optimization approach

In present work performance of coated carbide tool was investigated considering the effect of work material hardness and cutting parameters during turning of hardened AISI 4340 steel at different levels of hardness. The correlations between the cutting parameters and performance measures like cutting forces, surface roughness and tool life, were established by multiple linear regression models. The correlation coefficients found close to 0.9, showed that the developed models are reliable and could be used effectively for predicting the responses within the domain of the cutting parameters. Highly significant parameters were determined by performing an Analysis of Variance (ANOVA). Experimental observations show that higher cutting forces are required for machining harder work material. These cutting forces get affected mostly by depth of cut followed by feed. Cutting speed, feed and depth of cut having an interaction effect on surface roughness. Cutting speed followed by depth of cut become the most influencing factors on tool life; especially in case of harder workpiece. Optimum cutting conditions are determined using response surface methodology (RSM) and the desirability function approach. It was found that, the use of lower feed value, lower depth of cut and by limiting the cutting speed to 235 and 144 m/min; while turning 35 and 45 HRC work material, respectively, ensures minimum cutting forces, surface roughness and better tool life.     

Optimization of surface roughness and flank wear using the Taguchi method in milling of Hadfield steel with PVD and CVD coated inserts

In this paper, the Taguchi method and regression analysis have been applied to evaluate the machinability of Hadfield steel with PVD TiAlN- and CVD TiCN/Al₂O₃-coated carbide inserts under dry milling conditions. Several experiments were conducted using the L₁₈ (2 × 3 × 3) full-factorial design with a mixed orthogonal array on a CNC vertical machining center. Analysis of variance (ANOVA) was used to determine the effects of the machining parameters on surface roughness and flank wear. The cutting tool, cutting speed and feed rate were selected as machining parameters. The analysis results revealed that the feed rate was the dominant factor affecting surface roughness and cutting speed was the dominant factor affecting flank wear. Linear and quadratic regression analyses were applied to predict the outcomes of the experiment. The predicted values and measured values were very close to each other. Confirmation test results showed that the Taguchi method was very successful in the optimization of machining parameters for minimum surface roughness and flank wear in the milling the Hadfield steel.