共查询到20条相似文献,搜索用时 562 毫秒
1.
针对电压互感器二次回路防止误接线的方法进行了探讨。首先介绍了影响选择电压互感器二次绕组的主要参数及常见接线方式;然后提出了电压互感器投运前和运行中应注意的事项;最后提供了两种实用方法,从接线前和接线后两个方面分别对二次回路进行检查,以判断二次回路接线是否正确。研究结果表明,该方法具有广阔的推广应用前景。 相似文献
2.
卜黎玲 《China Equipment》2009,(8X):261-261
电压互感器具有电气隔离作用,能有效判断一次系统是否有接地或断线问题。而且在不同的接线方式下输出的电压也有所不同,通常根据测量的电压来判断电压二次回路接线正确性。本文针对电压互感器二次回路接线的试验程序及关键技术进行探讨,以期通过掌握互感器二次回路接线试验方法,提升继电保护及自动装置的安全可靠运行水平,全面提高继电保护及安全自动装置的正确动作率,确保电网安全稳定可靠运行。 相似文献
3.
按国家规程,电压互感器的二次回路的零相线必须一点接地,要求将变电站内的电压互感器的零相线与控制室的小母线连在一起,选择该小母线在保护屏内一点接地。通过对一次电压互感器二次回路零相线误接的实例进行分析,说明电压互感器二次回路的零相线接线的重要性。 相似文献
4.
结合我国普遍采用的V/v接线方式,枚举AB相电压互感器极性反接、CB相上电压互感器极性反接以及AB相与CB相电压互感器极性均反接3种情况,分别讨论了一组和二组电压互感器一、二次极性接反的现象及后果。 相似文献
5.
中性点不接地系统一般采用三相五柱式电压互感器,这种互感器接成Y_0/Y_0/(?)形接线,它既能测量线电压和相电压,又能组成绝缘监察装置和供单相接地保护用,故被广泛采用。这种电压互感器的二次接线方式,在设计手册或标准图集中都能查到,概括起来可分 相似文献
6.
目前变电所中10kV系统中性点加装零序互感器以消除谐振过电压,但随着公用电网谐波的影响,特别是三(3n)次谐波,在二次系统电压回路中产生了叠加,引起二次电压严重畸变。通过对3n次谐波在电压二次回路中产生的原因进行分析和计算,并利用M12292型电能质量分析仪对实际进行了检测,指出目前接线方式可能存在的不良后果,提出改进建议。 相似文献
7.
8.
9.
针对电压互感器二次回路压降所引起的计量误差问题,详细介绍了电能计量装置中关于电压互感器二次回路的配置要求及电压互感器专用二次回路的作用,并分析了电压互感器专用二次回路设计时应注意的问题。 相似文献
10.
11.
针对目前750 kV电容式电压互感器(CVT)测试中传统比较测差法和"低校高"法存在的问题,研究并开发出750 kV CVT测试和检验系统。通过对750 kV CVT的工作原理、等效电路和误差组成的分析,提出了750 kV CVT空载误差、负荷误差的测试方法和测试线路,研制了30.6 kV带升压器标准电压互感器、变频电子电源和低频互感器检验仪,组成了一套完整的检验系统。通过现场试验,测试数据准确可靠,可以满足0.2级750 kV CVT量值溯源的要求,具有较高的实用和推广价值。 相似文献
12.
13.
连慧峰 《机械工程与自动化》2006,(4):148-149
根据电流互感器的等值电路图,讨论了两种电流互感器变比检查试验方法(电流法和电压法)的原理和特点,推荐一种简便可靠的电流互感器变比现场检验法——电压法。 相似文献
14.
15.
基于配电变压器无功补偿完成了一种智能无功补偿控制器的硬件设计,装置以MSP430F133单片机为核心,安装在配电变压器的低压侧,实时监测电流、电压和功率因数,按无功需求控制多组不同容量的补偿电容进行投切.与以往控制器投切方式和补偿方式相比,提高了补偿精度以及设备的利用率.经实际运行表明,变压器二次侧功率因数控制在0.95 ~0.98之间,达到了预期的效果. 相似文献
16.
回复电压法是一种研究电力变压器绝缘老化状态的无损检测方法。回复电压含有丰富的反映绝缘状态的介电弛豫响应信息,为充分发挥回复电压法诊断油纸绝缘老化的优点,提出了利用驰豫电量评估变压器绝缘老化状态的新方法,并给出了相对驰豫电量与变压器油中糠醛含量的定量关系。首先,对回复电压曲线进行微分解谱求解回复电压的驰豫响应函数;其次,利用驰豫电量与驰豫响应函数的关系,计算出回复电压测量过程中的相对驰豫电量;最后,分析了相对驰豫电量与绝缘老化状态的关系。分析结果表明,驰豫电量对变压器油纸绝缘的老化非常敏感,相对驰豫电量Q_(1000)和Q_(500)与变压器油中糠醛含量存在较好的线性关系,相对驰豫电量可用于变压器油纸绝缘老化的定量评估。 相似文献
17.
变压器是电网中极其重要、极其普遍的一种电力设备。由于电网的电压随用电负荷的变化而相应变化,因此,也应对变压器的电压做随时调整;否则,电网电压的上升或下降会造成变压器损耗的加大,而且还会带来对安全的不利影响。研制的新型节能SZ11有载调压变压器具有在不停电的情况下,切换变压器调压档位进行调压,并随着电网电压的波动稳定负载中心的电压,调节负载潮流,合理配置电力资源的特点;同时,通过改进结构,改善性能,运用新技术、新材料、新工艺等措施,使该种变压器的结构更为合理,电气性能大为改善,节能效果更为显著。 相似文献
18.
In this study, a Rosen-type Pb(Mg(1/3)Nb(2/3))O(3)-PbTiO(3) single crystal piezoelectric transformer is presented. First, we simulate the operation of this transformer using the finite element method and ANSYS. By adjusting the dimensions of the piezoelectric transformer, a maximum voltage step-up ratio of 138 can be obtained at a frequency of 33.8 kHz when the output part is open. Second, we fabricate a transformer with the size of 20 mm length, 4 mm width, and 1 mm thickness to examine the simulation results. It is found that this transformer exhibits a maximum voltage step-up ratio of 134 at 37 kHz, with the efficiency over 95% when driving a liquid crystal display backlight, which shows good consistency with the numerical simulation results. Besides, we investigate the electrical properties under different frequencies and load resistances. When the input voltage increases, a maximum output power of 1 W is obtained with the temperature rise less than 10 degrees C. 相似文献
19.
For the power conditioning circuit used to deliver power efficiently from flux compression generator (FCG) to the load with high impedance, an air-cored and wire-wrapped transformer convenient in coaxial connection to the other parts is investigated. To reduce the size and enhance the performance, an auto-connection is adopted. A fast and simple model is used to calculate the electrical parameters of the transformer. To evaluate the high voltage capability, the voltages across turns and the electric field distribution in the transformer are investigated. The calculated and the measured electrical parameters of the transformer show good agreements. And the safe operating voltage is predicted to exceed 500 kV. In the preliminary experiments, the transformer is tested in a power conditioning circuit with a capacitive power supply. It is demonstrated that the output voltage of the transformer reaches -342 kV under the input voltage of -81 kV. 相似文献
20.
Shukla R Banerjee P Sharma SK Das R Deb P Prabaharan T Das B Adhikary B Verma R Shyam A 《The Review of scientific instruments》2011,82(10):106103
The experimental results of an air-core pulse transformer are presented, which is very compact (<10 Kg in weight) and is primed by a capacitor bank that is fabricated in such a way that the capacitor bank with its switch takes the shape of single-turn rectangular shaped primary of the transformer. A high voltage capacitor assembly (pulse-forming-line capacitor, PFL) of 5.1 nF is connected with the secondary of transformer. The transformer output voltage is 160 kV in its second peak appearing in less than 2 μS from the beginning of the capacitor discharge. The primary capacitor bank can be charged up to a maximum of 18 kV, with the voltage delivery of 360 kV in similar capacitive loads. 相似文献