Generation of atmospheric pressure air diffuse discharge plasma in oxygen enriched working gas with floating electrode

In this work, a floating electrode is employed to generate a stable large-area diffuse discharge plasma under an open oxygen-rich environment. The discharge image and the optical emission spectra of the N₂(C-B),N₂⁺(B-X), N²(B-A), and O(3p–3s, 777 nm) are measured to analyze the morphological and optical characteristics of the discharge. The effects of applied voltage, gas flow rate, and electrode gap on the reactive species, vibrational temperature and...     

Plasma Sheet Actuator Driven by Repetitive Nanosecond Pulses with a Negative DC Component

A type of electrical discharge called sliding discharge was developed to generate plasma aerodynamic actuation for flow control. A three-electrode plasma sheet actuator driven by repetitive nanosecond pulses with a negative DC component was used to generate sliding discharge, which can be called nanosecond-pulse sliding discharge. The phenomenology and behaviour of the plasma sheet actuator were investigated experimentally. Discharge morphology shows that the formation of nanosecond-pulse sliding discharge is dependent on the peak value of the repetitive nanosecond pulses and negative DC component applied on the plasma sheet actuator. Compared to dielectric barrier discharge (DBD), the extension of plasma in nanosecond-pulse sliding discharge is quasi-diffusive, stable, longer and more intensive. Test results of particle image velocimetry demonstrate that the negative DC component applied to a third electrode could significantly modify the topology of the flow induced by nanosecond-pulse DBD. Body force induced by the nanosecond-pulse sliding discharge can be approximately in the order of mN. Both the maximum velocity and the body force induced by sliding discharge increase significantly as compared to single DBD. Therefore, nanosecond-pulse sliding discharge is a preferable plasma aerodynamic actuation generation mode, which is very promising in the field of aerodynamics.     

Temporal evolution of atmospheric cascade glow discharge with pulsed discharge and radio frequency discharge

Atmospheric cascade discharges with pulsed discharge and radio frequency(RF)discharge were experimentally investigated by the temporal evolution of discharge spatial profile and intensity.The indium tin oxide(ITO)coated glass was employed as the transparent electrode to capture the discharge distribution above the electrode surface.It is demonstrated that in the pulsed discharge with dielectric barrier,the first discharge at the rising edge of pulse voltage is uniformly ignited and then forms an expanding plasma ring on the ITO electrode surface,which shrinks to the same diameter as that of bare stainless steel electrode with the generation of second discharge at the falling edge of pulse voltage.The discharge profiles along the electrode surface and discharge gap of the successive RF discharge are dependent on the intensity and spatial distribution of residual plasma species generated by the pulsed discharge,which is determined by the time interval between the pulsed discharge and RF discharge.It is demonstrated that the residual plasma species before the RF discharge ignition help to achieve the stable operation of RF discharge with elevated intensity.     

Numerical simulation of atmospheric pulse-modulated radio-frequency glow discharge ignition characteristics assisted by a pulsed discharge

A one-dimensional self-consistent fluid numerical model was developed to study the ignition characteristics of a pulse-modulated(PM) radio-frequency(RF) glow discharge in atmospheric helium assisted by a sub-microsecond voltage excited pulsed discharge. The temporal evolution of discharge current density and electron density during PM RF discharge burst was investigated to demonstrate the discharge ignition characteristics with or without the pulsed discharge. Under the assistance of pulsed discharge, the electron density in RF discharge burst reaches the magnitude of 1.87 × 10~(17) m~(-3) within 10 RF cycles, accompanied by the formation of sheath structure. It proposes that the pulsed discharge plays an important role in the ignition of PM RF discharge burst. Furthermore, the dynamics of PM RF glow discharge are demonstrated by the spatiotemporal evolution of the electron density with and without pulsed discharge. The spatial profiles of electron density, electron energy and electric field at specific time instants are given to explain the assistive role of the pulsed discharge on PM RF discharge ignition.     

Effect of actuating voltage and discharge gap on plasma assisted detonation initiation process

The influence of actuating voltage and discharge gap on plasma assisted detonation initiation by alternating current dielectric barrier discharge was studied in detail.A loose coupling method was used to simulate the detonation initiation process of a hydrogen–oxygen mixture in a detonation tube under different actuating voltage amplitudes and discharge gap sizes.Both the discharge products and the detonation forming process assisted by the plasma were analyzed.It was found that the patterns of the temporal and spatial distributions of discharge products in one cycle keep unchanged as changing the two discharge operating parameters.However,the adoption of a higher actuating voltage leads to a higher active species concentration within the discharge zone,and atom H is the most sensitive to the variations of the actuating voltage amplitude among the given species.Adopting a larger discharge gap results in a lower concentration of the active species,and all species have the same sensitivity to the variations of the gap.With respect to the reaction flow of the detonation tube,the corresponding deflagration to detonation transition(DDT) time and distance become slightly longer when a higher actuating voltage is chosen.The acceleration effect of plasma is more prominent with a smaller discharge gap,and the benefit builds gradually throughout the DDT process.Generally,these two control parameters have little effect on the amplitude of the flow field parameters,and they do not alter the combustion degree within the reaction zone.     

Analysis of Power in an Argon Filled Pulsed Dielectric Barrier Discharge

In this paper an argon filled coaxial dielectric barrier discharge (DBD) has been studied to understand the detail of power transfer from a unipolar square pulse to plasma during discharge. A dielectric barrier discharge based diffuse pulse discharge and its electrical characteristics are investigated. A quartz coaxial DBD tube filled at different pressures is used in the experiment. A unipolar pulse voltage of different peak voltages and frequencies has been applied to the discharge electrodes for the generation of microdischarges. Two current pulses are used for two consecutive discharges per applied voltage pulse. The second discharge, which occurs at the falling flank of the voltage pulse, is induced by the charges stored on the dielectric barrier during the first discharge. It has been deduced that the power supplied to ignite the first discharge is partly stored to ignite the second discharge when the applied voltage decays. This process ultimately leads to much improved power transfer to the plasma. The knowledge obtained from dynamic processes of the DBDs in the discharge gap explains quantitatively the mechanism of ignition, development and extinction of the DBDs.     

Characterization and comprehension of corona partial discharge in air under power frequency to very low frequency voltage

For the partial discharge test of electrical equipment with large capacitance, the use of lowfrequency voltage instead of power frequency voltage can effectively reduce the capacity requirements of test power supply. However, the validity of PD test under low frequency voltage needs to be evaluated. In order to investigate the influence of voltage frequency on corona discharge in the air, the discharge test of the tip-plate electrode under the frequency from 50 to 0.1 Hz is carried out based on the impulse current method. The results show that some of the main features of corona under low frequency do not change. The magnitude of discharge in a positive half cycle is obviously larger than that in a negative cycle. The magnitude of discharge and interval in positive cycle are random, while that in negative cycle are regular. With the decrease of frequency, the inception voltage increases. The variation trend of maximum and average magnitude and repetition rate of the discharge in positive and negative half cycle with the variation of voltage frequency and magnitude is demonstrated, with discussion and interpretation from the aspects of space charge transportation, effective discharge time and transition of discharge modes. There is an obvious difference in the phase resolved pattern of partial discharge and characteristic parameters of discharge patterns between power and low frequency. The experimental results can be the reference for mode identification of partial discharge under low frequency tests. The trend of the measured parameters with the variation of frequency provides more information about the insulation defect than traditional measurements under a single frequency (usually 50 Hz). Also it helps to understand the mechanism of corona discharge with an explanation of the characteristics under different frequencies.     

Characteristics of Electrode-Water-Electrode Discharge and its Application to Water Treatment

Atmospheric air discharge above the surface of water is an effective method for water treatment.The leakage current and Joule heating of water are reduced by the air gap,which raises the energy efficiency of the water treatment.However,the application of this kind of discharge is limited by a pair of conflicting factors：the chemical efficiency grows as the discharge gap distance decreases,while the spark breakdown voltage decreases as the gap distance decreases.To raise the spark breakdown voltage and the chemical efficiency of atmospheric pressure water surface discharge,both the high-voltage electrode and the ground electrode are suspended above the water surface to form an electrode-water-electrode discharge system.For this system,there are two potential discharge directions：from one electrode to another directly,and from the electrodes to the water surface.The first step in utilizing the electrode-water-electrode discharge is to find out the discharge direction transition criterion.In this paper,the discharge direction transition criterions of spark discharge and streamer discharge are presented.By comparing the discharge characteristics and the chemical efficiencies,the discharge propagating from the electrodes to the water surface is proved to be more suitable for water treatment than that propagating directly between the electrodes.     

Generation of reactive species in atmospheric pressure dielectric barrier discharge with liquid water

Atmospheric pressure helium/water dielectric barrier discharge(DBD) plasma is used to investigate the generation of reactive species in a gas–liquid interface and in a liquid. The emission intensity of the reactive species is measured by optical emission spectroscopy(OES)with different discharge powers at the gas–liquid interface. Spectrophotometry is used to analyze the reactive species induced by the plasma in the liquid. The concentration of OH radicals reaches 2.2 μm after 3 min of discharge treatment. In addition, the concentration of primary longlived reactive species such as H_2O_2, NO_3~- and O_3 are measured based on plasma treatment time.After 5 min of discharge treatment, the concentration of H_2O_2, NO_3~-, and O_3 increased from 0 mg?·?L~(-1) to 96 mg?·?L~(-1), 19.5 mg?·?L~(-1), and 3.5 mg?·?L~(-1), respectively. The water treated by plasma still contained a considerable concentration of reactive species after 6 h of storage. The results will contribute to optimizing the DBD plasma system for biological decontamination.     

Investigation on pulsed discharge mode in SF6-C2H6 mixtures

The non-chain chemical HF(DF)laser is one of the most powerful electrically-driven lasers operating in mid-infrared,in which SF6-C2H6 mixtures are often used as lasering media.Due to the electronegativity of SF6,the discharge in SF6-C2H6 presents a complicated discharge mode.To achieve reproducible pulsed laser output,pulsed discharge in SF6-C2H6 mixtures is investigated for discharge mode using plane electrodes assisted by array pre-ionization spark pins in cathode surface.Firstly,two modes can be distinguished.One mode is called the selfsustained volume discharge(SSVD),which is characterized by spatial uniformity in the discharge gap and pulse to pulse repeatability.On the contrary,another mode includes random arc passages in the discharge gap and therefore cannot conduct lasering.By varying discharge conditions(gap voltage,gas pressure,etc)two discharge modes are observed.Secondly,the holding scope of the SSVD mode is analyzed for the optimal mixture ratio of 20:1,and the boundary tend of the holding scope of SSVD indicates there exists maximum gas pressure and maximum charging voltage for SSVD.Finally,the peak current of SSVD relates positively to charging voltage,while negatively to gas pressure,from which it is drawn that synchronous electron avalanches initiated by the sliding array overlap spatially into SSVD and thus SSVD is essentially an α ionization avalanche.     

Experimental and numerical simulation study of the effect for the anode positions on the discharge characteristics of 300 W class low power Hall thrusters

Low-power Hall thruster(LHT) generally has poor discharge efficiency characteristics due to the large surface-to-volume ratio.Aiming to further refine and improve the performance of 300 W class LHT in terms of thrust and efficiency,and to obtain the most optimal operating point,the experimental study of the discharge characteristics for three different anode positions was conducted under the operation of various discharge voltages(100-400 V) and anode mass flow rates(0.65 mg·s^-1 and 0...     

Filament Discharge Phenomena in Fingerprint Acquisition by Dielectric Barrier Discharge

In this paper, the dielectric barrier discharge fingerprint acquisition technique is introduced. The filament discharge phenomena were observed in the process of fingerprint acquisition. The filament discharge reduced the quality of fingerprint images. Obviously, it was necessary to eliminate streamer discharges in order to get good fingerprint images. The streamer discharge was considered to be the cause of the filament discharge in the experiment. The relationship between the critical electric field and the discharge gap was calculated with the Raether＇s model of streamer discharge. The calculated results and our experiment proved that it would be difficult for the streamer discharge to occur when the discharge gap was narrow. With a narrow discharge gap, the discharge was homogeneous, and the fingerprint images were clear and large in area. The images obtained in the experiment are very suitable for fingerprint identification as they contain more information.     

Degradation and mineralization of ciprofloxacin by gas–liquid discharge non-thermal plasma

A typical quinolones antibiotic ciprofloxacin(CIP) in aqueous solution was degraded by a gas–liquid discharge non-thermal plasma system. The discharge plasma power and the emission intensity of the excited reactive species(RS) generated in the gas phase were detected by the oscilloscope and the optical emission spectroscopy. The effects of various parameters on CIP degradation, i.e. input powers, initial concentrations addition of radical scavengers and p H values were investigated. With the increase of discharge power, the degradation efficiency increased but the energy efficiency significantly reduced. The degradation efficiency also reduced under high concentration of initial CIP conditions due to the competitive reactions between the plasma-induced RS with the degradation intermediates of CIP. Different radical scavengers(isopropanol and CCl_4) on ·OH and H· were added into the reaction system and the oxidation effects of ·OH radicals have been proved with high degradation capacity on CIP.Moreover, the long-term degradation effect on CIP in the plasma-treated aqueous solution proved that the long-lived RS(H_2O_2 and O_3, etc) might play key roles on the stay effect through multiple aqueous reactions leading to production of ·OH. The degradation intermediates were determined by the method of electrospray ionization(+)-mass spectroscopy, and the possible degradation mechanism were presented.     

Study of ionic wind based on dielectric barrier discharge of carbon fiber spiral electrode

Based on the idea that a large number of charged particles can be generated by a high-frequency alternating current(AC)dielectric barrier discharge(DBD),and charged particles can be accelerated directionally by a direct current(DC)electric field,a new type of ionic wind formation method is proposed in this paper.To this end,a carbon fiber spiral electrode serves as the generation electrode and a metal rod electrode as the collection electrode,with AC and DC potentials applied respectively to the generation electrode and the collection electrode to form an AC-DC coupled electric field.Under the action of the coupled electric field,a dielectric barrier discharge is formed on the carbon fiber spiral electrode,and the electrons generated by the discharge move from the generation electrode to the collection electrode in the opposite direction of the electric field vectors.During the movement,energy is transferred to the gas molecules by their colliding with neutral gas molecules,thereby forming a directional gas stream movement,i.e.ionic wind.In the research process,it is verified through electric field simulation analysis and discharge experiment that this method can effectively increase the number of charged particles in the discharge process,and the velocity of the ionic wind is nearly doubled.On this basis,the addition of a third electrode forms a distinct discharge region and an electron acceleration region,which further increases its velocity.The experimental result shows that the ionic wind speed reaches up to 2.98 m s^?1.Thanks to the ability of the electrode structure to generate an atmospheric pressure DBD plasma and form an ionic wind,we can create a noise-free air purification device without resorting to a fan,with this device having good application prospects in the field of air purification.     

Simulation of Multi-Steady States in Low Temperature Gas Discharge

This article presents hydrodynamics simulation of multi-steady states and mode transition by DC-beam-injected gas discharge, and provides a model approach to hysteresis and distinct forms of multi-steady states. The critical transition conditions of the three discharge modes (temperature limited mode, Langmuir mode, and space charge limited mode) are estimated to be dependent on the gas pressure and the filament temperature. Various forms of the multi-steady states in gas discharge can be uniformly explained by the displacement of the mutant positions.The simulation results are in a good agreement with those of the experiments.     

Regulation characteristics of oxide generation and formaldehyde removal by using volume DBD reactor

Discharge plasmas in air can be accompanied by ultraviolet(UV) radiation and electron impact,which can produce large numbers of reactive species such as hydroxyl radical(OH·),oxygen radical(O·),ozone(O3),and nitrogen oxides(NOx),etc.The composition and dosage of reactive species usually play an important role in the case of volatile organic compounds(VOCs) treatment with the discharge plasmas.In this paper,we propose a volume discharge setup used to purify formaldehyde in air,which is configured by a plate-to-plate dielectric barrier discharge(DBD) channel and excited by an AC high voltage source.The results show that the relative spectral-intensity from DBD cell without formaldehyde is stronger than the case with formaldehyde.The energy efficiency ratios(EERs) of both oxides yield and formaldehyde removal can be regulated by the gas flow velocity in DBD channel,and the most desirable processing effect is the gas flow velocity within the range from2.50 to 3.33 m s-1.Moreover,the EERs of both the generated dosages of oxides(O3 and NO2) and the amount of removed formaldehyde can also be regulated by both of the applied voltage and power density loaded on the DBD cell.Additionally,the EERs of both oxides generation and formaldehyde removal present as a function of normal distribution with increasing the applied power density,and the peak of the function is appeared in the range from 273.5 to 400.0 W l-1.This work clearly demonstrates the regulation characteristic of both the formaldehyde removal and oxides yield by using volume DBD,and it is helpful in the applications of VOCs removal by using discharge plasma.     

Study of Atmospheric Pressure Abnormal Glow Discharge

Atmospheric pressure abnormal glow discharge （APAGD） was carried out simply with a transformer of 1 ： 500 driven by a alternating current with a frequency of 50 Hz. Typical stable discharge parameters, namely voltage of 400 V to 850 V and current of 60 mA to 110 mA were measured by oscillograph. Simulation of the discharge process suggested that the stable discharge was supported by the impedance from the secondary coil of the transformer, which offered a negative feedback to prevent the discharge from turning into an arc. An interpretation was given for the oscillogram of the sinuous discharge current and square voltage. Furthermore, the electron temperature and electron density averaged in the discharge channel of APAGD were estimated.     

A comparative study on the activity of TiO2 in pulsed plasma under different discharge conditions

In the present study,a combination of pulsed discharge plasma and TiO_2(plasma/TiO_2)has been developed in order to study the activity of TiO_2by varying the discharge conditions of pulsed voltage,discharge mode,air flow rate and solution conductivity.Phenol was used as the chemical probe to characterize the activity of TiO_2in a pulsed discharge system.The experimental results showed that the phenol removal efficiency could be improved by about 10%by increasing the applied voltage.The phenol removal efficiency for three discharge modes in the plasma-discharge-alone system was found to be highest in the spark mode,followed by the spark–streamer mode and finally the streamer mode.In the plasma/TiO_2system,the highest catalytic effect of TiO_2was observed in the spark–streamer discharge mode,which may be attributed to the favorable chemical and physical effects from the spark–streamer discharge mode,such as ultraviolet light,O_3,H_2O_2,pyrolysis,shockwaves and high-energy electrons.Meanwhile,the optimal flow rate and conductivity were 0.05 m~3l~(-1)and 10μS cm~(-1),respectively.The main phenolic intermediates were hydroquinone,catechol,and p-benzoquinone during the discharge treatment process.A different phenol degradation pathway was observed in the plasma/TiO_2system as compared to plasma alone.Analysis of the reaction intermediates demonstrated that p-benzoquinone reduction was selectively catalyzed on the TiO_2surface.The effective decomposition of phenol constant(D_e)increased from 74.11%to 79.16%when TiO_2was added,indicating that higher phenol mineralization was achieved in the plasma/TiO_2system.     

Discharge characteristics and reactive species production of unipolar and bipolar nanosecond pulsed gas–liquid discharge generated in atmospheric N_2

In this paper,unipolar pulse (including positive pulse and negative pulse) and bipolar pulse voltage are employed to generate diffuse gas–liquid discharge in atmospheric N_2with a rumpetshaped quartz tube.The current–voltage waveforms,optical emission spectra of excited state active species,FTIR spectra of exhaust gas components,plasma gas temperature,and aqueous H_2O_2,NO_2~-,andNO_3~-production are compared in three pulse modes,meanwhile,the effects of pulse peak voltage and gas flow rate on the production of reactive species are studied.The results show that two obvious discharges occur in each voltage pulse in unipolar pulse driven discharge,differently,in bipolar pulse driven discharge,only one main discharge appears in a single voltage pulse time.The intensities of active species (OH(A),and O(3p)) in all three pulsed discharge increase with the rise of pulse peak voltage and have the highest value at 200 ml min~(-1)of gas flow rate.The absorbance intensities of NO_2and N_2O increase with the increase of pulse peak voltage and decrease with the increase of gas flow rate.Under the same discharge conditions,the bipolar pulse driven discharge shows lower breakdown voltage,and higher intensities of excited species (N_2(C),OH(A),and O(3p)),nitrogen oxides (NO_2,NO,and N_2O),and higher production of aqueous H_2O_2,NO_2~-,andNO_3~-compared with both unipolar positive and negative discharges.     

Spectroscopic study of bipolar nanosecond pulse gas-liquid discharge in atmospheric argon

Atmospheric gas-liquid discharge with argon as a working gas is presented by employed nanosecond pulse power. The discharge is presented in a glow-like mode. The discharge powers are determined to be less than 1 W, and remains almost constant when the discharge duration time increases. Bountiful active species are determined by capturing optical emission spectra,and their main generation processes are also discussed. The plasma gas temperature is calculated as 350 K by comparing the experimental spectra and the simulated ones of N_2(C~3Ⅱ_g→B~3Ⅱ_g, Δv =-2). The time resolved vibrational and rotational temperature is researched to present the stability of discharge when pulse voltage and discharge duration vary.The electron density is determined to be 10~(16) cm~(-3) according to the Stark broadening effect of the H_α line.