Effect of exhaust gas recirculation on performance and emission characteristics of a diesel engine fuelled with tamarind biodiesel

The present research work focuses on the influence of exhaust gas recirculation (EGR) on the characteristics of the diesel engine operated with 20% tamarind seed methyl ester (TSME 20) as the renewable fuel. The use of TSME 20 as biodiesel results in closer performance characteristics with diesel fuel. However, TSME 20 biodiesel blend generated higher oxides of nitrogen (NO_X) emissions at all operating conditions. Firstly, tests are performed using diesel and TSME 20 biodiesel blend at constant speed under different loads. Thereafter, experiments are conducted on TSME 20 with EGR rates at different concentrations. The test results revealed that with TSME 20 with 20% EGR rate, NO_X emissions are reduced by 45.67% and 52.69% when compared to diesel and TSME 20. However, there is a slight reduction in brake thermal efficiency. Hence, the use of 20% EGR rate to TSME 20 is an optimum approach for better control of NO_X emissions.

Abbreviations BDC: bottom dead centre; BMEP: brake mean effective pressure; BSFC: brake-specific fuel consumption; BTE: brake thermal efficiency; CO: carbon monoxide; CO₂: carbon dioxide; EGR: exhaust gas recirculation; FSN: filter smoke number; HC: hydrocarbon; kWh: kilo Watt hour; NO_X: oxides of nitrogen; ppm: parts per million; SO: smoke opacity; TDC: top dead centre; TSME: tamarind seed methyl ester; TSME 20: 20% tamarind seed methyl ester; TSME 20–20%: tamarind seed methyl ester with 80% diesel; TSME 10% EGR: TSME 20 with 10% exhaust gas recirculation; TSME 20% EGR: TSME 20 with 20% exhaust gas recirculation; TSME 30% EGR: TSME 20 with 30% exhaust gas recirculation     

An experimental investigation of performance and emission characteristics of diesel engine with blends of cottonseed oil methyl ester with cold and hot EGR

An experimental investigation of diesel engine using cottonseed oil biodiesel and its blends with exhaust gas recirculation (EGR) techniques has been carried out. An optimum nozzle opening pressure of 250 bar and lower static injection timing of 20° before top dead centre (bTDC) are considered because it has been observed that these conditions only give minimum emissions. From the test results, it could be noted that there is an increasing trend of emission characteristics of HC, smoke density and NO_x for both cold and hot EGR for all blends of fuel with respect to brake power. As compared with cold EGR, the hot EGR gives lower emissions at all loads. In hot EGR, among the blends, at no-load and full-load conditions, the B100 gives the highest reduction in NO_x of 14.23% and 7.91%, respectively. However, the use of EGR leads to a rise in soot emission because of soot–NO_x trade-off for both the cases.     

Evaluation of performance and emission behaviour of DI diesel engine powered by biofuel

In this experiment, the performance, emission, and combustion characteristics of a diesel engine were tested using bio-fuel (Anise oil) at different loads. The main focus of this study was to compare the existing biodiesel blends with the proposed mixture (anise?+?cerium oxide) of biodiesel blends in terms of engine parameters, cost, efficiency, and pollution control. The blends used in this experiment are B10 (Biodiesel-10%), B20 (Biodiesel-20%), and B30 (Biodiesel-30%). The emission and performance parameters considered for the test are SFC (specific fuel consumption), CO (carbon monoxide), NO_X (nitrogen oxide), and HC (hydrocarbon). These parameters were tested for different load conditions such as 0%, 25%, 50%, 75%, and 100%. From the results, it shows that SFC is lower for B20 blend compared to that of pure diesel fuel, while B10, B30, B40, and B50 blends have slightly higher values. From the experiment, it is found that emissions of the HC and NO_x were reduced and CO emission is slightly higher than the pure diesel.     

The effect of engine emission on canola biodiesel blends with TiO2

The role of nanoparticles and nanofluid additives for biodiesel has gained consistent position in the current trend as they contribute to increase the performance of the engine with lower emission. In addition, additives also help to increase the engine reliability and lifespan. In this work, the effects of canola biodiesel blends of 20% proportions with diesel were investigated at 100% of engine load. The fuel is tested in a multi-cylinder water-cooled direct ignition (DI) engine. There are numerous notable works on nanofluid; however, the addition of TiO₂ nanoparticle as additive to produce canola biodiesel fuel is very limited. With the addition of the TiO₂ nanoparticle on Canola biodiesel blend in the DI engine, the exhaust property of gases such as CO, HC and NO_X is reduced. Furthermore, the combustion characteristics of the engine are improved. The canola biodiesel blends also resulted in lower NO_x emission as well as low smoke.     

Enhancement in the performance of a diesel engine fuelled with Pongamia methyl ester and n-butanol as oxygenated additive

The present paper investigates the performance and emission characteristics of a single-cylinder, four-stroke diesel engine fuelled with Pongamia methyl ester (PME) and n-butanol, at different loading conditions. Two blends of n-butanol–PME (10% and 20% n-butanol with PME on a volumetric basis) were prepared. The experimental results showed a significant improvement in the brake thermal efficiency of the engine with the blends and were found to increase with increasing percentage of n-butanol in the blends. The blended fuels also show lower emission such as carbon monoxide (CO), oxides of nitrogen (NO_x) and smoke opacity. However, unburned hydrocarbon (HC) emission was found to be slightly increased. Thus, it is concluded that the biodiesel with 20% n-butanol blend showed better results with respect to efficiency and emissions point of view compared with biodiesel.     

Optimisation of intake parameters for diesel engine fuelled with diesel-tamarind seed methyl ester biodiesel blend by Taguchi method

ABSTRACT

The present experimental work is focused on the use of Taguchi method to evaluate the optimum intake parameters to obtain the enhanced engine performance characteristics of diesel engine fuelled with TSME 20 (80% diesel and 20% Tamarind seed methyl ester) biodiesel blend. Injection pressure (IP), injection timing (IT) and exhaust gas recirculation (EGR) were considered as input parameters and each parameter at three levels. Brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), hydrocarbon (HC), oxides of nitrogen (NO_X) and smoke opacity (SO) were chosen as performance parameters. In this study, Taguchi L₂₇ orthogonal array (OA) was considered. Taguchi method is highly effective when dealing with responses influenced by several parameters; it significantly minimises the number of tests needed to model and optimise the responses influenced by various input parameters. In addition, an ANOVA test was conducted for the performance parameters to evaluate individual input parameters and its percentage contribution. It was found that IT has most significant on BTE; NO_X and smoke emission was highly influenced by EGR rate, followed by IT and IP.     

A comprehensive study on reduction of NOx emission applying EGR technique in a diesel engine using biodiesel (POME) as fuel with ether-based additives

The energy consumption is increasing rapidly due to population growth, improved living standards and industrialisation. A significant amount of fossil fuels is consumed by the transportation sector, which causes the fast depletion of fossil fuels and environmental pollution. These problems can be overcome by using Biodiesel. This research work aims to reduce the NO_x emission in diesel engines. The literature survey reveals that the use of a fuel additive reduces the emissions by oxygenating the fuel. Among oxygenates, ether proves to behave better than alcohols. Hence, for this present work, two different types of ethers were selected which were not used in earlier occasions. DGME (Diethylene Glycol Monomethyl Ether) and DGMB (Diethylene Glycol Monobutyl Ether) are the two additives selected from the ether group and used as additives with palm oil methyl ester (POME) biodiesel in various proportions and tested in a direct injection compression ignition engine which reduced the emissions. To start with, the engine was run with diesel and subsequently with biodiesel and with the additives. The performance tests were carried out in a single-cylinder, four-stroke, water-cooled engine with and without exhaust gas recirculation (EGR). This engine is coupled with eddy current dynamometer. The use of biodiesel in conventional diesel engines results in substantial reduction in emission of carbon monoxide, particulates and unburned hydrocarbons, but increases NO_x emission. This review focuses on reduction of NO_x emission. Combustion and performance analysis of the engine have also been evaluated.     

Experimental analysis of Deccan hemp oil as a new energy feedstock for compression ignition engine

This study investigates the biodiesel from Deccan hemp oil and its blends for the purpose of fuelling diesel engine. The performance and emission characteristics of Deccan hemp biodiesel are estimated and compared with diesel fuel. The experimental investigations are carried out with different blends of Deccan hemp biodiesel. Results show that brake thermal efficiency is improved significantly by 4.15% with 50 BDH when compared with diesel fuel. The Deccan hemp biodiesel reduces NO_x, HC and CO emission along with a marginal increase in CO₂ and smoke emissions with an increase in the biodiesel proportion in the diesel fuel. The improvement in heat release rates shows an increase in the combustion rate with different percentage blends of Deccan hemp biodiesel. From the engine test results, it has been established that 30–50 BDH of Deccan hemp biodiesel can be substituted for diesel.     

Performance and emission characteristics of cashew nut shell oil on the CI engine

This article is an effort to address the need for a non-cooking oil-based biodiesel. Here, the experimental work is done on a single cylinder, direct injection CI engine using cashew nut shell oil biodiesel blends under constant speed. The cashew nut shell liquid (CNSL) biodiesel is blended with the diesel fuel and used as biodiesel blend. Blends used for testing are B20, B40 and B60. The effect of the fuels on engine power, brake thermal efficiency (BTE) and exhaust gas temperature was determined by performance tests. The influences of blends on CO, CO₂, HC and NO_x emissions were investigated by emission tests. The BTE values of biodiesel are closer to diesel. Compared to diesel, all the biodiesel blends gave lesser unburnt hydrocarbon (HC), carbon monoxide (CO) and smoke emissions. Slightly higher NO_x emissions were found in CNSL biodiesel blends, which is typical of the other biodiesels.     

Experimental investigations on the influence of properties of Calophyllum inophyllum biodiesel on performance,combustion, and emission characteristics of a DI diesel engine

The current state of future energy and environmental crises has revitalised the need to find alternative sources of energy due to escalating oil prices and depleting oil reserves. To meet increasing energy requirements, there has been a growing interest in alternative fuels like biodiesel that can become a suitable diesel fuel substitute for compression ignition engine. Biodiesel offers a very promising alternative to diesel fuel, since they are renewable and have similar properties. Calophyllum inophyllum seed oil collected from different restaurants in the Nagapattinam region of South India was converted into methyl esters (biodiesel) by transesterification. Biodiesel produced from C. inophyllum oil was blended with diesel by different volume proportions (25%, 50%, and 75%). Biodiesel and its blends were tested on a direct injection (DI) diesel engine at a constant speed by varying loads from 0% to 100% in steps of 20% to analyse its performance, emission, and combustion characteristics. The results obtained were compared with that of diesel fuel. B25 (27.5%) showed better performance than diesel fuel (26.28%) at full load and B50 showed performances similar to diesel fuel. Smoke density of B25 was slightly (2.6%) higher than that of diesel at full load conditions. At full load, measured carbon monoxide emissions for B25 and B50 were 4% lower than that of diesel. Hydrocarbon emissions for B25 and B100 were 5.37% and 25.8% higher than that of diesel, respectively. Nitrogen oxides (NO_x) emission was lower for all biodiesel blends. NO_x emissions of B100 and B75 were lower than that of diesel by 22.16% and 13.29% at full load, respectively. Combustion profile was smoother, and no knocking problem was observed while operating with biodiesel blends. B75 produced peak cylinder pressure.     

Experimental study on particulate and NOx emissions of a diesel engine fueled with ultra low sulfur diesel, RME-diesel blends and PME-diesel blends

Ultra low sulfur diesel and two different kinds of biodiesel fuels blended with baseline diesel fuel in 5% and 20% v/v were tested in a Cummins 4BTA direct injection diesel engine, with a turbocharger and an intercooler. Experiments were conducted under five engine loads at two steady speeds (1500 rpm and 2500 rpm). The study aims at investigating the engine performance, NO_x emission, smoke opacity, PM composition, PM size distribution and comparing the impacts of low sulfur content of biodiesel with ULSD on the particulate emission. The results indicate that, compared to base diesel fuel, the increase of biodiesel in blends could cause certain increase in both brake specific fuel consumption and brake thermal efficiency. Compared with baseline diesel fuel, the biodiesel blends bring about more NO_x emissions. With the proportion of biodiesel increase in blends, the smoke opacity decreases, while total particle number concentration increases. Meanwhile the ULSD gives lower NO_x emissions, smoke opacity and total number concentration than those of baseline diesel fuel. In addition, the percentages of SOF and sulfate in particulates increase with biodiesel in blends, while the dry soot friction decreases obviously. Compared with baseline diesel fuel, the biodiesel blends increase the total nucleation number concentration, while ULSD reduces the total nucleation number concentration effectively, although they all have lower sulfur content. It means that, for ULSD, the lower sulfur content is the dominant factor for suppressing nucleation particles formation, while for biodiesel blends, lower volatile, lower aromatic content and higher oxygen content of biodiesel are key factors for improving the nucleation particles formation. The results demonstrate that the higher NO_x emission and total nucleation number concentration are considered as the big obstacles of the application of biodiesel in diesel engine.     

Study of emission characteristics of a diesel engine using cerium oxide nanoparticle blended pongamia methyl ester

In this work cerium oxide (CeO₂) nanoparticle was added to pongamia methyl ester (PME) to study its impact on emission characteristics in a diesel engine. It was found that CeO₂ nanoparticles act as an oxygen shelter owing to its high surface energy content due to its huge surface to volume ratio which expedites the process of combustion. Cerium oxide nanoparticles were mixed with neat PME at a different dose of 50?ppm and 100?ppm on a mass basis. CeO₂ nanoparticles are mixed to biodiesel by means of ultrasonicator and magnetic agitator to make sure homogenous. A diesel engine was used for the experimental analysis and fuelled with neat PME, diesel, PME dozed with CeO₂ nanoparticles at 50?ppm (PMEA50) and 100?ppm (PMEA100). Experimental results revealed that nanoparticle had an affirmative effect on emissions of PME as CeO₂ nanoparticles acted as a catalyst of oxidation. Amid the fuels containing CeO₂ nanoparticles, PMEA100 showed an improvement in various emissions as compared to conventional fuels. CeO₂ nanoparticles were to be the superior oxidising catalyst as it could effectively reduce CO and HC emissions. NO_x emission reduced appreciably owing to the catalytic activity of CeO₂ nanoparticles.     

Experimental analysis on a DI diesel engine with cerium-oxide-added Mahua methyl ester blends

An investigational research is carried out to found the performance and emission characteristics of a direct injection (DI) diesel engine with cerium oxide nanoparticles additives in diesel and biodiesel blends. Mahua methyl ester was produced by transesterification and blended with diesel. Cerium oxide nanoparticles of 50 and 100?ppm in proportion are subjected to high-speed mechanical agitation followed by ultra-sonication. The experimentations was conducted on a single cylinder DI diesel engine at a constant speed of 1500?rpm using different cerium-oxide (CeO₂)-blended biodiesel fuel (B20?+?50?ppm, B20?+?100?ppm, B50?+?50?ppm and B50?+?100?ppm) and the outcomes were compared with those of neat diesel and Mahua biodiesel blend (B20 and B50). The experimental results indicated that brake thermal efficiency of B20?+?100?ppm cerium oxide was increased by 1.8 with 1% betterment in specific fuel consumption. Emissions of hydrocarbon and carbon monoxide were reasonably lower than Diesel fuel.     

Effect of injection pressure on the performance and emission characteristics of the CI engine using Vateria indica biodiesel

Vateria indica Linn seeds were found to contain nearly 19% of oil/fat content. This fat is converted into biodiesel by a novel method by the authors at the biodiesel preparation facility at NITK, Surathkal, India. As biodiesel is a promising alternative fuel for petro diesel in compression ignition (CI) engines, this biofuel is tested in a single-cylinder diesel engine. The objective of this work is to find combustion, performance and emission characteristics of a CI engine with diesel and blends of V. indica biodiesel at 180, 200 and 220?bar injection pressures. Blending is done in volumetric ratios of 10%, 15%, 20% and 25% of biodiesel with diesel which are called as B10, B15, B20 and B25. The idea of increasing fuel injection pressure is to promote atomisation and full penetration into the combustion chamber leading to better combustion. Blend B25 showed best thermal efficiency of the order of 33.03% and the least NO_X emission of 1047?ppm at 220?bar injection pressure at 75% load.     

Experimental studies on the performance,emission and combustion characteristics of a biodiesel-fuelled (Pongamia methyl ester) diesel engine with diethyl ether as an oxygenated fuel additive

This paper investigates the combustion, performance and emission characteristics of a single-cylinder diesel engine using neat biodiesel (Pongamia methyl ester) with two different blends (10% and 15% diethyl ether [DEE]) at different load conditions. The measured values of brake thermal efficiency (BTE), brake specific fuel consumption (BSFC), exhaust gas temperature (EGT), carbon monoxide (CO), hydrocarbon (HC), nitrogen oxide (NO) and smoke were calculated and analysed and compared with diesel fuel. The results showed that a significant reduction in NO and smoke emissions for neat biodiesel with 15% DEE blend compared with neat biodiesel at full load conditions. The peak pressure and heat release rate were decreased, and maximum rate of pressure rise and ignition delay were also decreased with DEE blends at full load. On the whole, it is concluded that the biodiesel with 15% DEE blend showed better results with respect to efficiency and emissions point of view compared with biodiesel.     

Light vehicle regulated and unregulated emissions from different biodiesels

In this study, the regulated and unregulated emissions profile and fuel consumption of an automotive diesel and biodiesel blends, prepared from two different biodiesels, were investigated. The biodiesels were a rapeseed methyl ester (RME) and a palm-based methyl ester (PME). The tests were performed on a chassis dynamometer with constant volume sampling (CVS) over the New European Driving Cycle (NEDC) and the non-legislated Athens Driving Cycle (ADC), using a Euro 2 compliant passenger vehicle. The objectives were to evaluate the impact of biodiesel chemical structure on the emissions, as well as the influence of the applied driving cycle on the formation of exhaust emissions and fuel consumption. The results showed that NO_x emissions were influenced by certain biodiesel properties, such as those of cetane number and iodine number. NO_x emissions followed a decreasing trend over both cycles, where the most beneficial reduction was obtained with the application of the more saturated biodiesel. PM emissions were decreased with the palm-based biodiesel blends over both cycles, with the exception of the 20% blend which was higher compared to diesel fuel. PME blends led to increases in PM emissions over the ADC. The majority of the biodiesel blends showed a tendency for lower CO and HC emissions. The differences in CO₂ emissions were not statistically significant. Fuel consumption presented an increase with both biodiesels. Total PAH and nitro-PAH emission levels were decreased with the use of biodiesel independently of the source material. Lower molecular weight PAHs were predominant in both gaseous and particulate phases. Both biodiesels had a negative impact on certain carbonyl emissions. Formaldehyde and acetaldehyde were the dominant aldehydes emitted from both fuels.     

Experimental investigation of performance,combustion and emission characteristics of CI engine fuelled with chicha oil biodiesel

As the decreasing availability of the fossil fuel is rising day by day, the search of alternate fuel that can be used as a substitute to the conventional fuels is rising rapidly. A new type of biofuel, chicha oil biodiesel, is introduced in this work for the purpose of fuelling diesel engine. Chicha oil was transesterified with methanol using potassium hydroxide as catalyst to obtain chicha oil methyl ester (COME). The calorific value of this biodiesel is lower, when compared to that of diesel. The COME and their blends of 20%, 40%, 60% and 80% with diesel were tested in a single cylinder, four stroke, direct injection diesel engine and the performance, combustion and emission results were compared with diesel. The test result indicates that there is a slight increase in brake thermal efficiency and decrease in brake-specific fuel consumption for all blended fuels when compared to that of diesel fuel. The use of biodiesel resulted in lower emissions of CO and HC and increased emissions of CO₂ and NO_x. The experimental results proved that the use of biodiesel (produced from chicha oil) in compression ignition engine is a viable alternative to diesel.     

Bio-ethanol additive effect on direct injection diesel engine performance,emission and combustion characteristics – an experimental examination

ABSTRACT

The present investigation explores the effect of dairy scum oil methyl ester (DSOME) blends and ethanol additive on TV1 Kirloskar diesel engine performance, combustion and emission characteristics. From the experimental study, it is concluded that DSOME-B20 (20% dairy scum biodiesel?+?80% diesel) has shown appreciable performance and lower HC and CO emissions among all other blends. Hence DSOME-B20 is optimised as best fuel blend and it is carried for further investigations to study the effect of bio-ethanol additive on diesel engine performance. From the study it apparent that diesel engine operated with ethanol additive and 20% dairy scum biodiesel blended fuels shown the satisfactorily improved emission characteristics when compared to petroleum diesel fuel operation. Finally, from the experimental investigation, it concludes that addition of ethanol shown the slightly higher HC, CO emission and improved BTE, BSFC, NOx and CO₂ than sole B20 biodiesel blend. Among all three (3%, 6% and 9%) ethanol additive ratios, E6% (6%-ethanol with B20) ethanol additive exhibits slightly better BTE, BSFC, cylinder pressure and heat release rate hence 6% ethanol additive with B20 biodiesel blend would furnish beneficial effects in the diesel engine.     

Influence of injection timing on cerium oxide nanoparticle doped in waste cooking palm oil bio-diesel and diesel blends fuelled in diesel engine

ABSTRACT

Injection timing (IT) is a vital factor among different injection parameters which governs the emissions and performance factors of the engine. This work portrays the effect of IT on cerium oxide nanoparticle doped Waste Cooking Palm Oil biodiesel and diesel blends. The doping is made at 30, 60 and 90?ppm. The modified fuels are introduced in reducing IT of 19°, 21° and 23°bTDC. 1500?rpm engine is made use in this study. Results revealed a significant reduction in emissions (CO, NO_X, HC and Smoke) at IT?=?23°bTDC. Furthermore, performance (BSFC, BTE) is improved for fuel blends at IT?=?23°bTDC.     

The effect of exhaust gas recirculation on performance and emission characteristics of HCCI engine

In this work, performance and emission characteristics tests are conducted on homogeneous charge compression ignition (HCCI)-mode engine using mango seed methyl ester. And also the effect of exhaust gas recirculation (EGR) on performance and emission of HCCI engine is analysed. The three different percentages of EGR were added with intake fresh air at 15%, 30% and 45%. The objective of this work is to obtain the optimum EGR percentage based on engine performance and emissions. The brake thermal efficiency (BTE) slightly increased than conventional unmodified direct injection (DI) diesel engine. 15% of EGR shows higher BTE than other percentages of EGR added with HCCI engine. Specific fuel consumption of HCCI-mode engine is lower than the normal diesel engine. The exhaustion of harmful emission of oxides of nitrogen has been reduced when biodiesel is used in HCCI-mode engine. However, smoke and CO emissions were reduced in HCCI-mode engine compared with DI diesel engine and further decreased by using EGR in HCCI-mode engine. HC emissions are slightly increased for HCCI-mode engine.