Low dose powdered activated carbon addition at high sludge retention times to reduce fouling in membrane bioreactors

The addition of a low concentration of PAC (0.5 g L⁻¹ of sludge, i.e. a dose of 4 mg L⁻¹ of wastewater), in combination with a relatively long SRT (50 days), to improve membrane filtration performance was investigated in two pilot-scale MBRs treating real municipal wastewater. Continuous filterability tests at high flux showed the possibility to run for 18 h at 72 L m⁻² h⁻¹ and 180 h at 50 L m⁻² h⁻¹, while significant fouling occurred without PAC. In addition, measurements of the critical flux showed an increase of 10% for this strategy. Low dosage and high retention time makes it feasible and cost effective. Further advantages with regard to permeate quality and possible micropollutants removal are currently under investigation.     

Development of a novel fouling suppression system in membrane bioreactors using an intermittent electric field

A novel membrane bioreactor system that uses an intermittent electric field was successfully developed to suppress membrane fouling, caused mainly by activated sludge. We found that the surface of the activated sludge is negatively charged, and propose the utilization of an electric repulsive force to move the sludge away from the membrane by applying an electric field only when the permeate flux has drastically declined because of membrane fouling. The experimental results showed that a field of 6 V cm⁻¹, switched on and off every 90 s, significantly improved the removal of the activated sludge from the membrane and accordingly improved the average permeate flux.     

Identification and quantification of major organic foulants in treated domestic wastewater affecting filterability in dead-end ultrafiltration

Ultrafiltration (UF) membranes can be used after conventional wastewater treatment to produce particle free and hygienically safe water for reuse. However, membrane fouling affects the performance of UF to a large extent. Stirred cell tests with UF membrane show high flux decline filtering treated domestic wastewater. Investigation on the impact of size fractioned substances indicates that dissolved substances are major foulants affecting water filterability. Dissolved organic substances in feed and permeate samples of the stirred cell tests are analyzed by liquid chromatography with online organic carbon detection (LC-OCD). The resulting chromatograms displayed a significant difference of feed and permeate samples in the range of large molecules identified as biopolymer peak. The substances detected in this peak (mostly macro polysaccharide-like and protein-like molecules) are almost completely retained by UF membranes. Quantified investigation shows that biopolymer concentration influences filterability of corresponding water sample proportionally. The apparent magnitude of delivered biopolymer to membrane has a striking correlation with fouling resistance. The relationship was verified to be reproducible using different water samples. Mechanism analysis demonstrates that based on the delivered biopolymer load to membrane pore blocking or cake/gel fouling is the main fouling mechanism in the present experiment conditions.     

Characterization of dissolved extracellular organic matter (dEOM) and bound extracellular organic matter (bEOM) of Microcystis aeruginosa and their impacts on UF membrane fouling

Extracellular organic matter (EOM) of cyanobacteria was classified into the dissolved EOM (dEOM) which was released into culture solution and the bound EOM (bEOM) which surrounded the cells. The dEOM and bEOM extracted from Microcystis aeruginosa in stationary phase were used to study their characteristic differences and then their impacts on ultrafiltration (UF) membrane fouling. Component analyses showed that dEOM was comprised of proteins, polysaccharides and humic-like substances, while that bEOM contained only proteins and polysaccharides. Additionally, polysaccharides dominated in dEOM with a polysaccharide/DOC ratio of 1.11 mg mg⁻¹, while proteins were the primary components of bEOM with a protein/DOC ratio of 1.08 mg mg⁻¹. Results of size fractionation and XAD resin fractionation revealed that bEOM was mainly distributed in the high-MW and hydrophobic fractions, while that dEOM was more hydrophilic. Result of UF experiments indicated that dEOM which had a higher organic content and stronger hydrophilicity caused more severe flux decline and reversible fouling, and that bEOM led to slower flux decline but more irreversible fouling due to less electrostatic repulsive and more hydrophobic adhesion. The impacts of these two kinds of EOM on the UF fouling caused by cyanobacterial cells were also investigated. It was found that both flux decline and irreversible membrane fouling caused by the cells were aggravated when cells were together with EOM, especially for bEOM which might increase the surface hydrophobicity of the cells.     

Ultrafiltration membrane fouling by extracellular organic matters (EOM) of Microcystis aeruginosa in stationary phase: influences of interfacial characteristics of foulants and fouling mechanisms

This paper focused on the membrane fouling caused by extracellular organic matters (EOM) which was extracted from lab-cultured Microcystis aeruginosa in stationary phase. The characteristics of EOM such as molecular weight distribution, hydrophobicity and fluorescence were measured. It was found that high molecular weight (MW) and hydrophilic organics accounted for the major parts of algal EOM which was comprised of protein-like, polysaccharide-like and humic-like substances. Ultrafiltration (UF) experiments were carried out in a stirring cell and hydrophobic polyethersulfone (PES) membranes which carried negative charge were used. Prefiltration, calcium addition and XAD fractionation were employed to change the interfacial characteristics of EOM. Then the effects of these interfacial characteristics on flux decline, reversibility and mass balance of organics were compared. Algal EOM proved to cause serious membrane fouling during UF. The fraction of algal EOM between 0.45 μm and 100 kDa contributed a significant portion of the fouling. Hydrophobic organics in EOM tended to adhere to membrane surface causing irreversible fouling, while the cake layer formed by hydrophilic organics caused greater resistance to water flow due to hydrophilic interaction such as hydrogen bond and led to faster flux decline during UF. The results also indicated that the algal EOM was negatively charged and the electrostatic repulsion could prevent organics from adhering to membrane surface. In term of fouling mechanisms, cake layer formation, hydrophobic adhesion and pore plugging were the main mechanisms for membrane fouling caused by algal EOM.     

Removal of phenyl-urea herbicides in ultrapure water by ultrafiltration and nanofiltration processes

Membrane filtration of four phenyl-urea herbicides (linuron, diuron, chlortoluron, and isoproturon) dissolved in ultrapure water was studied in a laboratory cross-flow device in batch concentration mode (with recycling of the retentate stream). Three UF (MWCO of 20 000, 5000 and 2000 Da) and three NF (MWCO of 150-300 Da) membranes were used. The influence of the main operating conditions (transmembrane pressure, tangential velocity, temperature, pH, and MWCO of the membranes) on the steady-state permeate fluxes and the retention factors of the phenyl-ureas was evaluated. The herbicide mass adsorbed onto the membranes was also determined, and the contribution of the fouling resistance to the total resistance to permeate flux was much lower than the inherent resistance of the clean membranes.     

Identification and understanding of fouling in low-pressure membrane (MF/UF) filtration by natural organic matter (NOM)

An understanding of natural organic matter (NOM) as a membrane foulant and the behavior of NOM components in low-pressure membrane fouling are needed to provide a basis for appropriate selection and operation of membrane technology for drinking water treatment. Fouling by NOM was investigated by employing several innovative chemical and morphological analyses.

Source (feed) waters with a high hydrophilic (HPI) fraction content of NOM resulted in significant flux decline. Macromolecules of a relatively hydrophilic character (e.g. polysaccharides) were effectively rejected by low-pressure membranes, suggesting that macromolecular compounds and/or colloidal organic matter in the hydrophilic NOM fraction may be a problematic foulant of low-pressure membranes. Moreover, the significant organic fouling that is contributed by polysaccharides and/or proteins in macromolecular and/or colloidal forms depends on molecular shape (structure) as well as size (i.e. molecular weight). More significant flux decline was observed in microfiltration (MF) compared to ultrafiltration (UF) membrane filtration. MF membrane fouling may be caused by pore blockage associated with large (macromolecular) hydrophilic molecules and/or organic colloids. In the case of UF membranes, the flux decline may be caused by sequential or simultaneous processes of surface (gel layer) coverage during filtration. Morphological analyses support the notion that membrane roughness may be considered as a more important factor in membrane fouling by controlling interaction between molecules and the membrane surface, compared to the hydrophobic/hydrophilic character of membranes. Membrane fouling mechanisms are not only a function of membrane type (MF versus UF) but also depend on source (feed) water characteristics.     

大型超滤水厂PVC和PVDF膜运行特性差异与优化

超滤技术已广泛应用于城镇给水处理厂,使得饮用水水质得到显著改善。不同材质超滤膜的运行周期、膜通量、跨膜压差(TMP)等的变化规律会有显著的差异,需要根据各自的特点对超滤系统进行运行参数调控与优化,以保证超滤系统的长期稳定运行。分析了山东某大型超滤水厂超滤系统长期运行的特点,对比了PVC膜和PVDF膜孔结构特征、膜通量、跨膜压差变化趋势及膜过滤阻力特性,调控和优化超滤系统运行参数,并进行了长时间的运行验证。结果表明,膜孔径和膜孔结构不同造成的膜污染是PVC膜与PVDF膜过滤特性差异的主要因素,恒定过滤周期运行模式下PVC膜通量加速衰减时段为82~220 min,造成PVC膜通量衰减了9. 14%,并形成了约5%的永久衰减膜通量,而PVDF膜的通量衰减并不明显,使得水厂超滤系统在恒定过滤周期(180min)运行模式下,出现了PVC膜的污染速率明显高于PVDF膜、系统的运行工况出现显著差异的现象。按照恒定过滤阻力模式运行时,PVC膜和PVDF膜的最佳过滤周期范围分别为82~108 min和96~155 min。水厂超滤系统在恒定过滤阻力运行模式下将PVC膜与PVDF膜在高温期和低温期的过滤周期分别调整为110、90 min和150、120 min,TMP的增长速率和化学维护清洗周期均基本一致,超滤系统实现了长期稳定运行。研究成果为我国超滤水厂中不同材质超滤膜的运行参数优化及协同稳定运行提供了参考。     

Assessing PAC contribution to the NOM fouling control in PAC/UF systems

This paper investigates the powdered activated carbon (PAC) contribution to the fouling control by natural organic matter (NOM) in PAC/UF hybrid process, as well as the foulant behaviour of the PAC itself. Solutions of NOM surrogates (humic acids, AHA, and tannic acid, TA) and AOM/EOM (algogenic organic matter/extracellular organic matter) fractions from a Microcystis aeruginosa culture were permeated through an ultrafiltration (UF) hollow-fibre cellulose acetate membrane (100 kDa cut-off). The greatest impairment on flux and the poorest rejection were associated with polysaccharide-like EOM substances combined with mono and multivalent ions. PAC, either in the absence or in the presence of NOM, did not affect the permeate flux nor the reversible membrane fouling, regardless of the NOM characteristics (hydrophobicity and protein content) and water inorganics. However, PAC controlled the irreversible membrane fouling, minimising the chemical cleaning frequency. Furthermore, PAC enhanced AHA and TA rejections and the overall removal of AOM, although it was apparently ineffective for the highly hydrophilic EOM compounds.     

Combined coagulation-disk filtration process as a pretreatment of ultrafiltration and reverse osmosis membrane for wastewater reclamation: an autopsy study of a pilot plant

The effects of the combined coagulation-disk filtration (CC-DF) process on the fouling characteristics and behavior caused by interactions between effluent organic matter (EfOM) and the membrane surfaces of the ultrafiltration (UF) and reverse osmosis (RO) membranes in a pilot plant for municipal wastewater reclamation (MWR) were investigated. The feed water from secondary effluents was treated by the CC-DF process used as a pretreatment for the UF membrane to mitigate fouling formation and the permeate from the CC-DF process was further filtered by two UF membrane units in parallel arrangement and fed into four RO modules in a series connection. The CC-DF process was not sufficient to mitigate biofouling but the UF membrane was effective in mitigating biofouling on the RO membrane surfaces. Fouling of the UF and RO membranes was dominated by hydrophilic fractions of EfOM (e.g., polysaccharide-like and protein-like substances) and inorganic scaling (e.g., aluminum, calcium and silica). The desorbed UF membrane foulants included more aluminum species and hydrophobic fractions than the desorbed RO membrane foulants, which was presumably due to the residual coagulants and aluminum-humic substance complexes. The significant change in the surface chemistry of the RO membrane (a decrease in surface charge and an increase in contact angle of the fouled RO membranes) induced by the accumulation of hydrophilic EfOM onto the negatively charged RO membrane surface intensified the fouling formation of the fouled RO membrane by hydrophobic interaction between the humic substances of EfOM with relatively high hydrophobicity and the fouled RO membranes with decreased surface charge and increased contract angle.     

Effects of ozonation on the permeate flux of nanocrystalline ceramic membranes

Titania membranes, with a molecular weight cut-off of 15 kD were used in an ozonation/membrane system that was fed with water from Lake Lansing, which had been pre-filtered through a 0.45 microm glass fiber filter. The application of ozone gas prior to filtration resulted in significant decreases in membrane fouling. The effects of ozonation could not be explained by physical scouring of the filter cake. Decrease in the pH resulted in a concomitant increase in the dissolved ozone concentration in the feed water and in an improvement in permeate flux recovery. Increasing the ozone concentration beyond a threshold value had no beneficial effect on permeate flux recovery. Ozone decomposition, resulting in the formation of OH or other radicals at the membrane surface, is thought to result in the decomposition of organic foulants at the membrane surface and reduce the extent of membrane fouling.     

粉末活性炭吸附对超滤膜污染的影响研究

进行了粉末活性炭(PAC)吸附缓解浸没式和内压式超滤膜污染试验研究,并探讨了PAC吸附缓解膜污染的机理。浸没式超滤膜试验结果表明:PAC通过吸附溶解小分子有机物,减少了膜孔堵塞和膜孔内吸附污染,缓解了运行初期通量的快速下降;但PAC在膜表面的累积会降低浸没式超滤膜的起始通量。内压式超滤膜试验结果表明:膜前PAC吸附预处理能提高对有机物的去除效能,降低膜表面的污染负荷,从而降低TMP及其增长速度。     

Alginate block fractions and their effects on membrane fouling

Alginate has been commonly used as a model foulant in studies of membrane organic fouling. As a complex polymer, alginate is composed of two different monomers, namely M ((1 → 4) linked β-D-mannopyranuronic acid) and G ((1 → 4) linked α-L-gulopyranuronic acid) which are randomly arranged into MG-, MM- and GG-blocks. So far, little information is available about fouling propensity of each block in microfiltration. In this study, microfiltration experiments were conducted respectively with MG-, MM- and GG-blocks separated from alginate under defined conditions. Results showed the severest fouling in the filtration of MG-block, and the least flux decline in the filtration of MM-block. The initial pore blocking was found to be responsible for the fouling observed in MG-block filtration, while the cake layer formed on membrane surface during the MM-block filtration could serve as a pre-filter that prevented membrane from further pore blocking. In order to look into fouling mechanisms, the effects of transparent exopolymeric particles (TEP) on membrane fouling were also studied. TEP were found to form through aggregation or cross-link of alginate blocks. As TEP were bigger than original alginate blocks, they could facilitate the formation of cake layer on membrane surface. It was observed that more TEP were produced from MM-blocks than from MG-blocks in solutions. This in turn explained why cake resistance was dominant in the filtration of MM-blocks as compared to MG-blocks. The analysis by the extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory further revealed that MM-blocks had lowest cohesive interaction energy among all three alginate blocks, which favoured aggregation of MM-blocks, and ultimately leading to the formation of more TEP. This study provided insights into the roles of different alginate blocks in development of membrane fouling, and suggested that the membrane fouling would be related to molecular structure of alginate.     

Studies on the effect of humic acids and phenol on adsorption-ultrafiltration process performance

Application of pressure-driven membrane processes, such as ultrafiltration (UF) and microfiltration (MF) for surface water treatment have become very popular during last decades. Membrane fouling by humic substances (HS) is one of the major limiting factors in these processes. In order to alleviate the unfavorable effects of the presence of HS in the feed on the process performance UF and MF are often combined with adsorption on powdered activated carbon (PAC). The main goal of the present study was to evaluate the effect of humic acid (HA) on membrane fouling during UF. Moreover, the effect of PAC addition to the feed on UF process, especially on flux decline was determined. The applicability of the adsorption-ultrafiltration (PAC/UF) system to purification of water containing low (phenol) and high molecular (HA) was also investigated. Three different polymer UF membranes, prepared from polysulfone (PSF), cellulose acetate (CA) or polyacrylonitrile (PAN) were applied. It was found that the membranes prepared from PSF and CA are very susceptible to fouling caused by HA. The permeate flux decreased for ca. 50% during UF of HA solution through the PSF membrane and for ca. 45%-through the CA membrane. In the case of the PAN membrane, a negligible effect of HA on the flux was observed. On the basis of the FTIR spectra it was found that the drop in the permeate flux through these membranes may result from interactions between the negatively charged functional groups present on the membrane surface, such as carboxyl groups (CA) and sulfone groups (PSF) with HA, which results in coating of the membrane surface with HA. When PAC was added to the feed containing HA, the permeate flux through the CA and PAN membranes was maintained on a practically unchanged level. However, in case of the PSF membrane, a 50% drop in the permeate flux in comparison with the flux value, when process was conducted without PAC addition was observed. That was supposed to be due to attractive forces among hydrophobic PAC particles, HA molecules and PSF membrane surface. The performed studies showed that the application of PAC/UF system was very effective in the removal of organic substances having both, low and high molecular weights. The role of PAC suspended in a feed in the PAC/UF system is the adsorption of low molecular organic compounds, which cannot be removed by UF alone.     

Size distribution of methylmercury associated with particulate and dissolved organic matter in freshwaters

Water samples were collected from 20 wetland, river and lake sites across Eastern Ontario and Western Quebec to investigate the distribution of methylmercury (MeHg) associated with various size fractions of dissolved organic matter (DOM). Tangential Flow UltraFiltration (TUF) was used to fractionate DOM by nominal molecular size (<0.2 μm, <300 kDa, <30 kDa, <5 kDa and <1 kDa). DOM fluorescence (DOM FL) and absorbance (DOC Abs) were used to quantify DOM photoreactivity and aromaticity in each sample. Significant differences in the size-associated distribution of MeHg, Dissolved Organic Carbon (DOC), DOM FL, and DOM Abs were observed between wetlands, rivers, and lakes. The low molecular weight (LMW) fraction (<5 kDa) in wetlands contained the majority of MeHg (70.0 ± 13.8%), DOC (56.1 ± 9.4%), and DOM FL (77.4 ± 7.5%). DOM FL was also high in the LMW fraction for rivers (60.6 ± 25%) and lakes (75.2 ± 16.9%). Mean MeHg concentrations in the LMW fraction of lakes (41 ± 26 pg L^− 1) and rivers (32 ± 19 pg L^− 1) were substantial but much lower than wetlands. Rivers had the highest percentage of methylmercury (38.0 ± 23.5%) in the particulate (>0.2 µm) fraction. This research highlights the importance of low molecular weight dissolved organic matter in methylmercury fate. For example, a large proportion of MeHg was found in the LMW weight fractions (mean = 47.3 ± 25.4%) of the wetlands, rivers, and lakes in this study.     

Vacuum membrane distillation of seawater reverse osmosis brines

Seawater desalination by Reverse Osmosis (RO) is an interesting solution for drinking water production. However, because of limitation by the osmotic pressure, a high recovery factor is not attainable. Consequently, large volumes of brines are discharged into the sea and the flow rate produced (permeate) is limited. In this paper, Vacuum Membrane Distillation (VMD) is considered as a complementary process to RO to further concentrate RO brines and increase the global recovery of the process. VMD is an evaporative technology that uses a membrane to support the liquid-vapour interface and enhance the contact area between liquid and vapour in comparison with conventional distillation. This study focuses on VMD for the treatment of RO brines. Simulations were performed to optimise the operating conditions and were completed by bench-scale experiments using actual RO brines and synthetic solutions up to a salt concentration of 300 g L⁻¹. Operating conditions such as a highly permeable membrane, high feed temperature, low permeate pressure and a turbulent fluid regime allowed high permeate fluxes to be obtained even for a very high salt concentration (300 g L⁻¹). For the membrane studied, temperature and concentration polarisation were shown to have little effect on permeate flux. After 6 to 8 h, no organic fouling or biofouling was observed for RO brines. At high salt concentrations, scaling occurred (mainly due to calcium precipitation) but had only a limited impact on the permeate flux (24% decrease for a permeate specific volume of 43L m⁻² for the highest concentration of salt). Calcium carbonate and calcium sulphate precipitated first due to their low solubility and formed mixed crystal deposits on the membrane surface. These phenomena only occurred on the membrane surface and did not totally cover the pores. The crystals were easily removed simply by washing the membrane with water. A global recovery factor of 89% can be obtained by coupling RO and VMD.     

Flux patterns and membrane fouling propensity during desalination of seawater by forward osmosis

The membrane fouling propensity of natural seawater during forward osmosis was studied. Seawater from the Red Sea was used as the feed in a forward osmosis process while a 2 M sodium chloride solution was used as the draw solution. The process was conducted in a semi-batch mode under two crossflow velocities, 16.7 cm/s and 4.2 cm/s. For the first time reported, silica scaling was found to be the dominant inorganic fouling (scaling) on the surface of membrane active layer during seawater forward osmosis. Polymerization of dissolved silica was the major mechanism for the formation of silica scaling. After ten batches of seawater forward osmosis, the membrane surface was covered by a fouling layer of assorted polymerized silica clusters and natural organic matter, especially biopolymers. Moreover, the absorbed biopolymers also provided bacterial attachment sites. The accumulated organic fouling could be partially removed by water flushing while the polymerized silica was difficult to remove. The rate of flux decline was about 53% with a crossflow velocity of 16.7 cm/s while reaching more than 70% with a crossflow velocity of 4.2 cm/s. Both concentration polarization and fouling played roles in the decrease of flux. The salt rejection was stable at about 98% during seawater forward osmosis. In addition, an almost complete rejection of natural organic matter was attained. The results from this study are valuable for the design and development of a successful protocol for a pretreatment process before seawater forward osmosis and a cleaning method for fouled membranes.     

Comparison of humic acid rejection and flux decline during filtration with negatively charged and uncharged ultrafiltration membranes

Increasingly stringent regulations for drinking water quality have stimulated the ultrafiltration (UF) to become one of the best alternatives replacing conventional drinking water treatment technologies. However, UF is not very effectively to remove humic acid due to the comparatively larger pore size compared to the size of humic acid. Fouling issue is another factor that restricts its widespread application. In this study, rejection of humic acid and flux decline were compared with essentially neutral, negatively charged version of a regenerated cellulose membrane, in which electrostatic interaction was explored for a better humic acid removal and less fouling. Solution environment, including ionic strength, pH and calcium ion concentration, affecting humic acid removal and flux decline on negatively charged and neutral membranes was also compared. Results indicated that the appropriate charge modification on the neutral UF membrane could be an effective way for better removal of NOM and reduction of the membrane fouling due to the electrostatic interactions with the combination effect of membrane pore size. Electrostatic interactions are significant important to achieve high humic acid removal and less fouling, and to improve the water quality and protect people’s health.     

Comparison of MFI-UF constant pressure, MFI-UF constant flux and Crossflow Sampler-Modified Fouling Index Ultrafiltration (CFS-MFI UF)

Understanding the foulant deposition mechanism during crossflow filtration is critical in developing indices to predict fouling propensity of feed water for reverse osmosis (RO). Factors affecting the performance on different fouling indices such as MFI-UF constant pressure, MFI-UF constant flux and newly proposed fouling index, CFS-MFI_UF were investigated. Crossflow Sampler-Modified Fouling Index Ultrafiltration (CFS-MFI_UF) utilises a typical crossflow unit to simulate the hydrodynamic conditions in the actual RO units followed by a dead-end unit to measure the fouling propensity of foulants. CFS-MFI_UF was found sensitive to crossflow velocity. The crossflow velocity in the crossflow sampler unit influences the particle concentration and the particle size distribution in its permeate. CFS-MFI_UF was also found sensitive to the permeate flux of both CFS and the dead-end cell. To closely simulate the hydrodynamic conditions of a crossflow RO unit, the flux used for CFS-MFI_UF measurement was critical. The best option is to operate both the CFS and dead-end permeate flux at flux which is normally operated at industry RO units (∼20 L/m² h), but this would prolong the test duration excessively. In this study, the dead-end flux was accelerated by reducing the dead-end membrane area while maintaining the CFS permeate flux at 20 L/m² h. By doing so, a flux correction factor was investigated and applied to correlate the CFS-MFI_UF measured at dead-end flux of 120 L/m² h to CFS-MFI_UF measured at dead-end flux of 20 L/m² h for RO fouling rate prediction. Using this flux correction factor, the test duration of CFS-MFI_UF can be shortened from 15 h to 2 h.     

Removal of arsenic from contaminated groundwater by solar-driven membrane distillation using three different commercial membranes

Investigations on solar-driven membrane distillation (SDMD) were carried out for removal of arsenic from contaminated groundwater. Three different types of hydrophobic membranes made of polytetrafluoroethylene (PTFE) and polypropylene (PP) with surface area of 120 × 10⁻⁴ m² were used as flat sheet in a direct contact membrane distillation (DCMD) set up in a cross flow module. Effects of initial arsenic concentration in the feed, feed velocity, feed temperature and distillate inlet temperature on arsenic removal efficiency and flux were studied where temperatures of feed and distillate were found to have significant effect on the flux. Almost 100% arsenic separation was achieved without wetting membrane pore even after 120 h of operation. The PTFE membrane with a flux of 49.80 kg/m² h was found to the best one out of the tested membranes. The study shows that solar-driven DCMD can effectively separate arsenic from groundwater using a cross flow membrane module with PTFE hydrophobic membrane.