Gas turbine steam injection and combined power cycles using fog inlet cooling and biomass fuel: A thermodynamic assessment

The results of energy and exergy analyses of two biomass integrated steam injection cycles and combined power cycles are reported. Fog cooling, steam injection and adding steam turbine cycles to gas turbine cycles can enhance the performance of power generation systems. Even with its lower heat value, biomass can be substituted for fossil fuels. The performances of the cycles are assessed under the same conditions. The assessments show that the combined cycle has a higher efficiency at lower values of compressor pressure ratio but the steam injection plant is advantageous at higher pressure ratio values. The steam injection plant has a higher net power under the same conditions, while the exergy loss rate is higher for the combined cycle at all pressure ratios. But the exergy destruction rate is higher for the steam injection cycle at lower compressor pressure ratios, and for the combined cycle at higher pressure ratios.     

A modern injected steam gas turbine cogeneration system based on exergy concept

Factors such as low capital cost, good match of power and heat requirements and proven reliability can sometimes lead an end user into purchasing gas turbines for use in a modern cogeneration plant. The steam‐injected gas turbine is an attractive electrical generating technology for mitigating the impacts of rising energy prices. According to such mentioned above this paper is to provide results of an optimization study on cogeneration power cycle, which works by gas turbine with recuperator and injection steam added to the combustor of the gas turbine. The performance characteristics of the cycle based on energy and exergy concepts and based upon practical performance constraints were investigated. The effect of the recuperator on the cycle was greatly clarified. Results also show that the output power of a gas turbine increases when steam is injected. When extra steam has to be generated in order to be able to inject steam and at the same time to provide for a given heat demand, power generating efficiency increases but cogeneration efficiency decreases with the increasing of injected steam. Copyright © 2004 John Wiley & Sons, Ltd.     

A critical assessment of thermo‐economic analyses of different air bottoming cycles for waste heat recovery

Steam turbine cycle's low operating temperature makes it suitable for waste heat recovery applications. Even though conventional combined cycles, ie, topping gas turbine and bottoming steam turbine cycles, are thermodynamically efficient, they are not the most economical alternatives for power generation with capacities less than 50 MWe. A recently proposed alternative is to utilize a bottoming gas turbine cycle in form of an air bottoming cycle. In this study, an overview of air bottoming cycle is presented. Based on the discussed studies, it is decided to further evaluate the merits of water injection in the bottoming cycle air stream by using either a humidifier or an air saturator. Thermo‐economic analysis and optimization are performed to evaluate simple and water injected air bottoming cycles against steam bottoming cycles. Results indicate that conventional combined cycles can achieve the highest thermal efficiency of about 48%. While water injected air bottoming cycle with air saturator is the most cost effective combined cycle configuration and most efficient air bottoming cycle with levelized cost of electricity and energy efficiency of 64.41 US$/MWh and 39%–40%, respectively, followed by the water injected air bottoming cycle with humidifier and simple air bottoming cycle with reported levelized cost of electricity of 65.75 US$/MWh, 66.36 US$/MWh, respectively. Steam bottoming cycle has the highest levelized cost of electricity of 68.88 US$/MWh.     

氢能燃气轮机循环低温能有效利用及热力学分析

为了充分利用液氢的低温Ｙｏｎｇ，在气能燃气轮机循环中附加了一个空气预冷器和氢气透平。该循环的比功，热效率，Ｙｏｎｇ效率均较简单循环燃气轮机有很大提高。本文对液氢－燃气动力循环进行了热力学分析，指出它的优越的动力性能。     

Integrated solar combined cycle system with steam methane reforming: Thermodynamic analysis

The present paper considers an integrated solar combined cycle system (ISCCS) with an utilization of solar energy for steam methane reforming. The overall efficiency was compared with the efficiency of an integrated solar combined cycle system with the utilization of solar energy for steam generation for a steam turbine cycle. Utilization of solar energy for steam methane reforming gives the increase in an overall efficiency up to 3.5%. If water that used for steam methane reforming will be condensed from the exhaust gases, the overall efficiency of ISCCS with steam methane reforming will increase up to 6.2% and 8.9% for β = 1.0 and β = 2.0, respectively, in comparison with ISCCS where solar energy is utilized for generation of steam in steam turbine cycle. The Sankey diagrams were compiled based on the energy balance. Utilization of solar energy for steam methane reforming increases the share of power of a gas turbine cycle: two-thirds are in a gas turbine cycle, and one-third is in a steam turbine cycle. In parallel, if solar energy is used for steam generation for a steam turbine cycle, than the shares of power from a gas and steam turbine are almost equal.     

Thermoeconomic modeling and parametric study of hybrid SOFC–gas turbine–steam turbine power plants ranging from 1.5 to 10 MWe

Detailed thermodynamic, kinetic, geometric, and cost models are developed, implemented, and validated for the synthesis/design and operational analysis of hybrid SOFC–gas turbine–steam turbine systems ranging in size from 1.5 to 10 MWe. The fuel cell model used in this research work is based on a tubular Siemens-Westinghouse-type SOFC, which is integrated with a gas turbine and a heat recovery steam generator (HRSG) integrated in turn with a steam turbine cycle. The current work considers the possible benefits of using the exhaust gases in a HRSG in order to produce steam which drives a steam turbine for additional power output. Four different steam turbine cycles are considered in this research work: a single-pressure, a dual-pressure, a triple pressure, and a triple pressure with reheat. The models have been developed to function both at design (full load) and off-design (partial load) conditions. In addition, different solid oxide fuel cell sizes are examined to assure a proper selection of SOFC size based on efficiency or cost. The thermoeconomic analysis includes cost functions developed specifically for the different system and component sizes (capacities) analyzed. A parametric study is used to determine the most viable system/component syntheses/designs based on maximizing total system efficiency or minimizing total system life cycle cost.     

Performance analysis of open cycle gas turbines

In this study, the performance of ideal open cycle gas turbine system was examined based on its thermodynamic analysis. The effects of some parameters, such as compressor inlet temperature (CIT), pressure ratio (PR) and the turbine inlet temperature (TIT), on the performance parameters of open cycle gas turbine were discussed. The turbine net power output, the thermal efficiency and the fuel consumption of the turbine were taken as the performance parameters. The values of these parameters were calculated using some basic cycle equations and variables values of thermodynamic properties. Other variables such as lower heating value, combustion efficiency and isentropic efficiencies of compressor and turbine were assumed to be constant. The result showed that the net power output and the thermal efficiency increased by a decrease in the CIT and increase in the TIT and PR values. If it is aimed to have a high net power output and the thermal efficiency for the turbine, the CIT should be chosen as low as possible and the TIT should be chosen as high as possible. Copyright © 2008 John Wiley & Sons, Ltd.     

Energetic and exergetic analysis of a hybrid combined‐nuclear power plant

Combined‐cycle power plants are currently preferred for new power generation plants worldwide. The performance of gas‐turbine engines can be enhanced at constant turbine inlet temperatures with the addition of a bottoming waste‐heat recovery cycle. This paper presents a study on the energy and exergy analysis of a novel hybrid Combined‐Nuclear Power Plant (HCNPP). It is thus interesting to evaluate the possibility of integrating the gas turbine with nuclear power plant of such a system, utilizing virtually free heat. The integration arrangement of the AP600 NPP steam cycle with gas turbines from basic thermodynamic considerations will be described. The AP600 steam cycle modifications to combine with the gas turbines can be applied to other types of NPP. A simple modeling of Alstom gas turbines cycle, one of the major combined‐cycle steam turbines manufacturers, hybridized with a nuclear power plant from energetic and exergetic viewpoint is provided. The Heat Recovery Steam Generator (HRSG) has single steam pressure without reheat, one superheater and one economizer. The thermodynamic parameters of the working fluids of both the gas and the steam turbines cycles are analyzed by modeling the thermodynamic cycle using the Engineering Equation Solver (EES) software. In case of hybridizing, the existing Alstom gas turbine with a pressurized water nuclear power plants using the newly proposed novel solution, we can increase the electricity output and efficiency significantly. If we convert a traditional combined cycle to HCNPP unit, we can achieve about 20% increase in electricity output. This figure emphasizes the significance of restructuring our power plant technology and exploring a wider variety of HCNPP solutions. Copyright © 2011 John Wiley & Sons, Ltd.     

蒸-燃联合循环与燃-燃联合循环的模拟和对比

蒸汽-燃气联合循环装置由于其较高的发电效率而被广泛应用于各大、中型电厂。然而,在微小型燃气-蒸汽发电装置中,蒸汽轮机的应用无疑使得装置体积和成本费用大增。因此,本文提出在小型分布式发电装置中,采用环境压力吸热燃气轮机循环（APGC）装置来替代蒸汽轮机装置吸收燃气轮机排出的废气能量,组成燃-燃联合循环,增加系统本身的做功能力和效率,达到节能、减少燃料消耗的目的。本文从热力学第一定律和第二定律出发,基于ASPENPLUS软件分别建立了燃-燃联合循环、蒸-燃联合循环模型,比较分析了两种循环装置在能量质量和数量上的利用程度。结果表明：燃-燃联合循环装置的效率较高,这在要求能源高效利用的今天具有一定的理论意义。     

Performance evaluation of a combined power generation system integrated with thermochemical exhaust heat recuperation based on steam methane reforming

The present paper applies the thermodynamic analysis with the determining the efficiency of a combined cycle power plant with a chemically recuperated gas turbine. Thermochemical recuperation of exhaust heat after a gas turbine is realized via the steam methane reforming process. The main concept of combined cycle power plant (CCPP) with chemically recuperated gas turbine (CRGT) is based on the use of exhaust heat for endothermic reforming of the original hydrocarbon fuel in a reformer and for steam generation for a steam cycle. To understand the effect of operating variables such as temperature, pressure, and steam-to-methane ratio on the overall efficiency, the energy and mass balances were compiled. The energy flows were represented by a Sankey diagram. The results of the thermodynamic analysis show that efficiency of CCPP with CRGT is significantly higher (4–7%) than efficiency of CCPP with a conventional gas turbine without TCR. Maximum efficiency of CCPP with CRGT of 0.6412 is observed at inlet temperature of working gas of 1600 °C, pressure of 23 bar for a steam-to-methane ratio of 3.0. In the temperature of inlet working gas below 1200 °C the increase in the efficiency of CCPP with TCR is less than 2%.     

Modeling,numerical optimization,and irreversibility reduction of a triple-pressure reheat combined cycle

The main methods for improving the efficiency of the combined cycle are: increasing the inlet temperature of the gas turbine (TIT), reducing the irreversibility of the heat recovery steam generator (HRSG), and optimization. In this paper, modeling and optimization of the triple-pressure reheat combined cycle as well as irreversibility reduction of its HRSG are considered. Constraints were set on the minimum temperature difference for pinch points (PP_m), the temperature difference for superheat approach, the steam turbine inlet temperature and pressure, the stack temperature, and the dryness fraction at steam turbine outlet. The triple-pressure reheat combined cycle was optimized at 41 different maximum values of TIT using two different methods; the direct search and the variable metric. A feasible technique to reduce the irreversibility of the HRSG of the combined cycle was introduced. The optimized and the reduced-irreversibility triple-pressure reheat combined cycles were compared with the regularly designed triple-pressure reheat combined cycle, which is the typical design for a commercial combined cycle. The effects of varying the TIT on the performance of all cycles were presented and discussed. The results indicate that the optimized triple-pressure reheat combined cycle is up to 1.7% higher in efficiency than the reduced-irreversibility triple-pressure reheat combined cycle, which is 1.9–2.1% higher in efficiency than the regularly designed triple-pressure reheat combined cycle when all cycles are compared at the same values of TIT and PP_m. The optimized and reduced-irreversibility combined cycles were compared with the most efficient commercially available combined cycle at the same value of TIT.     

燃气轮机循环有限时间热力学研究新进展

在概述有限时间热力学理论产生和发展的基础上,着重介绍了运用该理论对闭、开式燃气轮机简单和复杂循环以及燃气轮机热电和热电冷联产循环性能进行热力学分析和优化的最新研究进展。指出了由于有限时间热力学理论进一步充分考虑了实际装置中的不可逆性,因此得到的循环最优性能是综合最佳的,同时也发现了一些与经典热力学理论研究不同的新结果。     

Comparative exergoeconomic analyses of the integration of biomass gasification and a gas turbine power plant with and without fogging inlet cooling

Inlet cooling is effective for mitigating the decrease in gas turbine performance during hot and humid summer periods when electrical power demands peak, and steam injection, using steam raised from the turbine exhaust gases in a heat recovery steam generator, is an effective technique for utilizing the hot turbine exhaust gases. Biomass gasification can be integrated with a gas turbine cycle to provide efficient, clean power generation. In the present paper, a gas turbine cycle with fog cooling and steam injection, and integrated with biomass gasification, is proposed and analyzed with energy, exergy and exergoeconomic analyses. The thermodynamic analyses show that increasing the compressor pressure ratio and the gas turbine inlet temperature raises the energy and exergy efficiencies. On the component level, the gas turbine is determined to have the highest exergy efficiency and the combustor the lowest. The exergoeconomic analysis reveals that the proposed cycle has a lower total unit product cost than a similar plant fired by natural gas. However, the relative cost difference and exergoeconomic factor is higher for the proposed cycle than the natural gas fired plant, indicating that the proposed cycle is more costly for producing electricity despite its lower product cost and environmental impact.     

Thermodynamic investigation of solar energy-based triple combined power cycle

The present work deals with the thermodynamic analysis of a solar-powered triple combined power cycle to generate emission-free power. The triple combined cycle comprises one topping cycle as Brayton cycle and two bottoming cycles, namely, steam Rankine cycle (SRC) and organic Rankine cycle (ORC). The Brayton cycle employs double-stage compression with intercooling. During intercooling, heat energy rejected by the compressed air was further utilized in the ORC. The energy carried away after the turbine exit was used in the SRC. The proposed cycle performance is investigated for three working fluids to use with the bottoming ORC. Results showed that the maximum overall thermal efficiency and work output of solar energy-based triple combined cycle are found 21.89% and 218.98 kJ/kg air, respectively, for organic fluid R245fa at the topping cycle pressure ratio of 31.     

9FA型燃气轮机联合循环性能研究

1引言西气东输工程促进了沿线燃气轮机联合循环电厂的建设,减轻了中东部地区的环境排放压力。燃气轮机联合循环发电系统高效低污染、启停迅速、调峰能力强。西气东输管道沿线有25台F级燃气轮机联合循环机组,其中GE公司9FA型燃气轮机联合循环发电机组13台。如何保证系统的稳定安     

整体煤气化湿化燃气轮机循环热力性能分析

本文以降低NOX排放和有效利用低品位热量为出发点,将燃料或空气湿化应用到整体煤气化燃气轮机循环中。基于水煤浆激冷或废锅流程气化炉,构建了多种整体煤气化湿化燃气轮机循环并分析了其热力性能。研究表明：燃料湿化循环系统效率较高;空气湿化循环燃气轮机比功较大;无论采用何种湿化方式,废锅流程循环系统效率都要高于激冷流程;蒸汽底循环保留的空气湿化循环系统具有利用系统外部中低品位热量、大幅提高系统效率的潜力。     

开式燃气轮机中冷回热再热循环功率和效率优化

建立了开式燃气轮机中冷回热再热（ICRR）循环有限时间热力学模型,导出了循环功率和效率解析式,优化了气流沿通流部分的压降（或低压压气机进口空气质量流率）和中间压比,得到最大功率;并在给定燃油流率的情况下,优化了气流沿通流部分的压降和中间压比,得到最大热效率,进一步在给定低压压气机进口和动力涡轮出口总面积的情况下,优化两者面积分配比,得到双重最大热效率.     

不同的燃气轮机调控方案对燃气—蒸汽联合循环电站性能的影响

以某燃气－蒸汽联合循环电站的主要配置 基础，计算并分析比较了在改变燃料 量和调节压气机可转导叶等不同调控方案对燃气－蒸联合循环各3个组成部分及总体性能的影响，从而为燃气－蒸汽联合循环电站合理选择燃气轮机调控方案提供有意义的参考。     

退役航空涡扇发动机地面应用的有效途径之一_再热燃气_蒸汽联合循环

本文探讨以退役航空涡扇发动机作为燃气发生器，内函的燃气与外函的空气相掺混。经再热燃烧室加热后进入动力涡轮作功，并且应用余热锅炉回收－部分排气余热，产生蒸汽，驱动汽轮机作功所组成的再热热气－蒸汽联合循环。通过计算实例说明该循环具有输出功率大，循环效率具有相当大的提高等特点。     

具有空气冷却的简单循环燃气轮机热力学建模和性能优化:(I)建模

研究了考虑空气冷却和实际气体性质的简单循环三轴燃气轮机热力学性能,给出了循环功率和效率的计算流程,并利用UGT25000型工业燃气轮机的设计性能数据对模型进行了验证计算。结果表明,所建模型是准确的,能有效地反映燃气轮机循环的设计性能。