Performance analysis of a waste‐heat‐powered thermodynamic cycle for multieffect refrigeration

A multieffect refrigeration system that is based on a waste‐heat‐driven organic Rankine cycle that could produce refrigeration output of different magnitudes at different levels of temperature is presented. The proposed system is integration of combined ejector–absorption refrigeration cycle and ejector expansion Joule–Thomson (EJT) cooling cycle that can meet the requirements of air‐conditioning, refrigeration, and cryogenic cooling simultaneously at the expense of industrial waste heat. The variation of the parameters that affect the system performance such as industrial waste heat temperature, refrigerant turbine inlet pressure, and the evaporator temperature of ejector refrigeration cycle (ERC) and EJT cycles was examined, respectively. It was found that refrigeration output and thermal efficiency of the multieffect cycle decrease considerably with the increase in industrial waste heat temperature, while its exergy efficiency varies marginally. A thermal efficiency value of 22.5% and exergy efficiency value of 8.6% were obtained at an industrial waste heat temperature of 210°C, a turbine inlet pressure of 1.3 MPa, and ejector evaporator temperature of 268 K. Both refrigeration output and thermal efficiency increase with the increase in turbine inlet pressure and ERC evaporator temperature. Change in EJT cycle evaporator temperature shows a little impact on both thermal and exergy efficiency values of the multieffect cycle. Analysis of the results clearly shows that the proposed cycle has an effective potential for cooling production through exploitation of lost energy from the industry. Copyright © 2014 John Wiley & Sons, Ltd.     

Parametric analysis for a new combined power and ejector–absorption refrigeration cycle

A new combined power and ejector–absorption refrigeration cycle is proposed, which combines the Rankine cycle and the ejector–absorption refrigeration cycle, and could produce both power output and refrigeration output simultaneously. This combined cycle, which originates from the cycle proposed by authors previously, introduces an ejector between the rectifier and the condenser, and provides a performance improvement without greatly increasing the complexity of the system. A parametric analysis is conducted to evaluate the effects of the key thermodynamic parameters on the cycle performance. It is shown that heat source temperature, condenser temperature, evaporator temperature, turbine inlet pressure, turbine inlet temperature, and basic solution ammonia concentration have significant effects on the net power output, refrigeration output and exergy efficiency of the combined cycle. It is evident that the ejector can improve the performance of the combined cycle proposed by authors previously.     

Proposal and analysis of a novel ammonia–water cycle for power and refrigeration cogeneration

Cogeneration has improved sustainability as it can improve the energy utilization efficiency significantly. In this paper, a novel ammonia-water cycle is proposed for the cogeneration of power and refrigeration. In order to meet the different concentration requirements in the cycle heat addition process and the condensation process, a splitting /absorption unit is introduced and integrated with an ammonia–water Rankine cycle and an ammonia refrigeration cycle. This system can be driven by industrial waste heat or a gas turbine flue gas. The cycle performance was evaluated by the exergy efficiency, which is 58% for the base case system (with the turbine inlet parameters of 450 °C/11.1 MPa and the refrigeration temperature below −15 °C). It is found that there are certain split fractions which maximize the exergy efficiency for given basic working fluid concentration. Compared with the conventional separate generation system of power and refrigeration, the cogeneration system has an 18.2% reduction in energy consumption.     

First and second law analysis of an ejector expansion Joule–Thomson cryogenic refrigeration cycle

In this paper, a combined first and second law approach is applied to study an ejector expansion Joule–Thomson cryogenic refrigeration cycle. The effects of the evaporator temperature, ejector pressure ratio and compressor function on the coefficient of performance (COP), exergy destruction and the exergetic efficiency have been investigated. The present study has been conducted for the evaporator and compressor temperature in the range of 75–135 and 270–330 K, respectively. The ejector pressure ratio is varied from 1.5 to 5.5. Simulation results show that COP and exergy efficiency increase with increasing evaporator temperature and ejector pressure ratio. In addition, it was found that the increase in the compressor temperature leads to the reduction in the first and second law efficiencies. Copyright © 2010 John Wiley & Sons, Ltd.     

Exergy analysis,parametric analysis and optimization for a novel combined power and ejector refrigeration cycle

A new combined power and refrigeration cycle is proposed, which combines the Rankine cycle and the ejector refrigeration cycle. This combined cycle produces both power output and refrigeration output simultaneously. It can be driven by the flue gas of gas turbine or engine, solar energy, geothermal energy and industrial waste heats. An exergy analysis is performed to guide the thermodynamic improvement for this cycle. And a parametric analysis is conducted to evaluate the effects of the key thermodynamic parameters on the performance of the combined cycle. In addition, a parameter optimization is achieved by means of genetic algorithm to reach the maximum exergy efficiency. The results show that the biggest exergy loss due to the irreversibility occurs in heat addition processes, and the ejector causes the next largest exergy loss. It is also shown that the turbine inlet pressure, the turbine back pressure, the condenser temperature and the evaporator temperature have significant effects on the turbine power output, refrigeration output and exergy efficiency of the combined cycle. The optimized exergy efficiency is 27.10% under the given condition.     

Exergy analysis of Joule–Thomson cryogenic refrigeration cycle with an ejector

In this paper, exergy method is applied to analyze the ejector expansion Joule–Thomson (EJT) cryogenic refrigeration cycle. The exergy destruction rate in each component of the EJT cycle is evaluated in detail. The effect of some main parameters on the exergy destruction and exergetic efficiency of the cycle is also investigated. The most significant exergy destruction rates in the cycle are in the compressor and ejector. The ejector pressure ratio and compressor isothermal efficiency have a significant effect on the exergetic efficiency of the EJT cycle. The exergy analysis results show the EJT cycle has an obvious increase in the exergetic efficiency compared to the basic Joule–Thomson refrigeration cycle. A significant advantage from the use of the ejector is that the total exergy destruction of the EJT cycle can be reduced due to much more decreasing of the exergy destruction rates in the compressor and expansion valve. The exergy analysis also reconfirms that applying an ejector is a very important approach to improve the performance of the Joule–Thomson cryogenic refrigeration cycle.     

Energy and exergy analysis of novel solar bi‐ejector refrigeration system with injector

Energy and exergy balances were done on a novel solar bi‐ejector refrigeration system with R123, whose circulation pump is replaced by an injector. The analysis result of the novel system was compared with that of the original one. The effect of operation condition on system energy efficiency, exergy efficiency and exergy loss was analyzed, and the dynamic performance of a designed solar bi‐ejector refrigeration system was also studied. The comparative results indicate that under the same operating condition, the novel system and the original system have equal energy efficiency, exergy efficiency and exergy loss, and the only difference between them is the exergy losses of the generators and the added injector. The other conclusions mainly include: the solar collector has the largest exergy loss rate of over 90% and for the bi‐ejector refrigeration subcycle, the ejector has the largest exergy loss rate of about 5%; the total exergy loss changes inversely proportional to the evaporation temperature and positively proportional to the condensation temperature; when the other parameters are fixed, there exists an optimum generation temperature, at which the overall energy and exergy efficiencies are both the maximum and the total exergy loss is the minimum. The study points out the direction for optimizing the novel solar bi‐ejector refrigeration system. Copyright © 2009 John Wiley & Sons, Ltd.     

First and second law investigations of a new solar‐assisted thermodynamic cycle for triple effect refrigeration

This investigation is persuaded for the first and second law analyses of a new solar‐driven triple‐effect refrigeration cycle using Duratherm 600 oil (Duratherm Extended Life Fluid, NY, USA) as the heat transfer fluid is performed. The proposed cycle is an integration of ejector, absorption, and cascaded refrigeration cycles that could produce refrigeration output of different magnitude at different temperature simultaneously. Both exergy destruction and losses in each component and hence in the overall system are determined to identify the causes and locations of the thermodynamic imperfection. The effects of some influenced parameters such as hot oil outlet temperature, refrigerant turbine inlet pressure, and the evaporator temperature of ejector and cascaded refrigeration cycle have been observed on the first and second law performances. It is found that maximum irreversibility occurs in central receiver as 52.5% and the second largest irreversibility of 25% occurs in heliostat field. The second law efficiency of the solar driven triple effect refrigeration cycle is 2%, which is much lower than its first law efficiency of 11.5%. Analysis clearly shows that performance evaluation based on the first law analysis is inadequate and hence, more meaningful evaluation must be included in the second law analysis. Copyright © 2013 John Wiley & Sons, Ltd.     

Parametric analysis and optimization for a combined power and refrigeration cycle

A combined power and refrigeration cycle is proposed, which combines the Rankine cycle and the absorption refrigeration cycle. This combined cycle uses a binary ammonia–water mixture as the working fluid and produces both power output and refrigeration output simultaneously with only one heat source. A parametric analysis is conducted to evaluate the effects of thermodynamic parameters on the performance of the combined cycle. It is shown that heat source temperature, environment temperature, refrigeration temperature, turbine inlet pressure, turbine inlet temperature, and basic solution ammonia concentration have significant effects on the net power output, refrigeration output and exergy efficiency of the combined cycle. A parameter optimization is achieved by means of genetic algorithm to reach the maximum exergy efficiency. The optimized exergy efficiency is 43.06% under the given condition.     

First and second laws analysis of the heat pipe/ejector refrigeration cycle

Integration of the heat pipe with an ejector will result in a compact and high performance system. The concept of the heat pipe/ejector refrigeration cycle is discussed, in this paper. The needed driving capillary forces are firmly established. The basic characteristics of the system, such as entrainment ratio, coefficient of performance, exergy efficiency and thermal efficiency of the system are evaluated. Also, the zero-dimensional constant pressure mixing theory is applied to ejector. In this study, water is used as the working fluid. Whenever the mixed flow is supersonic, a normal shockwave is assumed to occur upstream of diffuser inlet. The simulation results indicate that, the coefficient of performance can reach about 0.30 at T_e = 10 °C, T_c = 30 °C and T_g = 100 °C. Also, the second law efficiency of the heat pipe/ejector refrigeration cycle increases with increasing evaporator temperature and decreasing condenser temperature. It is seen that, the maximum heat pipe cooling capacity obtains for large heat pipe diameters, near the small heat pipe lengths. It has proven that, this refrigeration system can be widely used in many areas, especially in renewable energy utilization such as solar energy.     

Transient simulation of a solar-based hydrogen production plant with evacuated tube collector and ejector refrigeration system

This article is a careful examination of an energy poly-generation unit integrated with an evacuated solar thermal tube collector. A proton exchange membrane (PEM) electrolysis unit is used for hydrogen production, an ejector refrigeration system (ERS) is utilized for cooling demand, and a heater unit is used for heating demand. All sub-systems are validated by considering recent articles. Cooling and heating demand, as well as the net output power are calculated. The modeled poly-generation system's exergy and energy efficiency are maximized by considering the inlet temperature of the heat exchanger and primary pressure of the ejector with the parametric evaluation of the system. The proposed poly-generation set-up can produce cooling load, heating load, and hydrogen with amounts of 5.34 kW, 5.152 kW, and 63 kg/year, respectively. Based on these values, the energy ef?ciency, and exergy ef?ciency are computed to be 64.14%, and 49.62%, respectively. Higher energy and exergy ef?ciencies are obtained by reducing high pressure of the refrigeration cycle or decreasing the temperature outlet of an auxiliary heater. The heat exchanger and thermal energy storage unit have the highest cost rate among all system components with 73,463 $ and 46,357, respectively. Parametric study indicates that the main determinative elements in the total cost rate of the system are the heater, and the solar collector.     

Thermodynamic and exergy evaluation of an innovative hydrogen liquefaction structure based on ejector-compression refrigeration unit,cascade multi-component refrigerant system,and Kalina power plant

Considerable recent ecological and energy concerns have aroused the exploitation of sustainable resources and cost-effective production of green energy carriers such as liquid hydrogen. Despite the remarkable merits of the multi-component refrigerant cycle in enhancing the hydrogen liquefaction process efficiency, it contributes to problematic controllability, increasing investment costs. Moreover, it is not easily possible to keep the composition share of refrigerants in case of leakage. This paper develops an innovative integrated structure for liquid hydrogen production, which benefits from the compression-ejector unit and six cascade multi-component refrigerant cycles in the pre-cooling and liquefaction stages. The Kalina power generation uses wasted heat in the integrated system. A power of 595.6 MW is necessary to produce 22.34 kg/s liquid hydrogen, resulting in specific energy consumption (SEC) of 7.405 kWh/kg LH2 and a coefficient of performance (COP) of 0.103. Besides, the COP of the compression-ejector refrigeration cycle is 0.8682, and the thermal efficiency of the Kalina cycle is 0.1228. The exergy efficiencies of the proposed structure and the ejector-compression refrigeration cycles are 0.2359 and 0.6462, respectively. Heat exchangers take the lion's share of exergy destruction with 39.55%, followed by gas turbines (27.92%) and compressors (21.81%). Based on sensitivity analysis, with the pressure increase in the secondary stream of Ejector1, the SEC increases by 7.435 kWh/kgLH2, and the COP of the ejector-compression refrigeration cycle decreases by 0.8242. As the pressure rises in the Kalina cycle, the SEC declines to a low of 7.4135 kWh/kg LH2 at 26 bar, then increases with pressure.     

非共沸混合工质压缩制冷循环的不可避免(火用)损失

以非共沸混合工质替代 CFCS是比较有效的替代方案。通过对给定节点温差下的蒸发器和冷凝器内的温度匹配分析 ,提出利用调节非共沸混合工质的配比来优化蒸发器和冷凝器内的温度匹配 ,并可计算出循环的实际不可避免灯用损失 ,从而提出采用非共沸混合工质的蒸气压缩制冷循环的实际不可避免灯用损失的计算方法 ,并提出利用最佳配比和实际不可避免的灯用损失的计算 ,对各种非共沸混合工质对进行筛选 ,以进一步减少循环可避免的灯用损失 ,为优化蒸气压缩制冷循环 ,提高循环的性能奠定基础。     

Exergy analysis of multistage cascade refrigeration cycle used for natural gas liquefaction

This paper provides an exergy analysis of the multistage cascade refrigeration cycle used for natural gas liquefaction. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. Also, an expression for the minimum work requirement for the liquefaction of natural gas is developed. It is shown that the minimum work depends only on the properties of the incoming and outgoing natural gas, and it increases with decreasing liquefaction temperature. The minimum work for a typical natural gas inlet and exit state is determined to be 456.8 kJ kg^?1 of liquefied natural gas (LNG), which corresponds to a coefficient of performance (COP) of 1.8. Using a typical actual work input value; the exergetic efficiency of the multistage cascade refrigeration cycle is determined to be 38.5% indicating a great potential for improvements. Copyright © 2002 John Wiley & Sons, Ltd.     

Process development of a solar-assisted multi-production plant: Power,cooling, and hydrogen

Multi-production is a practical approach to boost the efficiency of energy conversion systems by utilizing waste energy to producing more commodities in comparison to conventional single output plants. Solar energy is a vast source of energy that has the potential to be employed for different purposes. Therefore, in this research, a solar-driven multi-production system of power, cooling, and hydrogen generation is proposed and evaluated for being implemented in the city of Bandar-Abbas. The overall system is evaluated by calculating the exergy efficiency and exergy destruction rate of each equipment of the multi-production system. Based on the obtained results, heat exchangers, valves and drums, and splitters monitor to be the most exergy destructive equipment compared to other equipment in the multi-production system. In overall, the designed multi-production system reaches the overall energy efficiency of 90.77% and the overall exergy efficiency of 92.19%. In addition, the coefficient of performance is 0.39 for the absorption refrigeration cycle of the designed multi-production system. In overall, the designed system is able to produce 4.36 MW of electricity, 1.65 MW of cooling load, and 2026 kg/h of hydrogen generation at 80.86°C and 2068 kPa.     

Experimental investigation of integrated refrigeration system (IRS) with gas engine,compression chiller and absorption chiller

An integrated refrigeration system (IRS) with a gas engine, a vapor-compression chiller and an absorption chiller is set up and tested. The vapor-compression refrigeration cycle is operated directly by the gas engine. The waste heat from the gas engine operates the absorption refrigeration cycle, which provides additional cooling. The performance of the IRS is described. The cooling capacity of the IRS is about 596 kW, and primary energy ratio (PER) reaches 1.84 at air-conditioning rated conditions. The refrigerating capacity of the prototype increased and PER of prototype decreased with the increase of the gas engine speed. The gas engine speed was preferably regulated at part load condition in order to operate the prototype at high-energy efficiency. The refrigerating capacity and PER of the prototype increased with the increase of the outlet temperature of chilled water or the decrease of the inlet temperature of cooling water. The integrated refrigeration chiller in this work saves running costs as compared to the conventional refrigeration system by using the waste heat.     

CO2双蒸发器压缩/喷射式跨临界制冷循环

为减小CO_2跨临界循环系统节流部分的膨胀功损失,提高系统性能,可在小型制冷系统中采用喷射器代替节流阀,部分回收工质从高压到低压过程的膨胀功。在对系统进行热力学分析的基础上,建立了CO_2跨临界压缩／喷射制冷循环的效率分析模型。计算结果表明：在合理的喷射器出口背压下,CO_2跨临界压缩／喷射制冷循环可以得到较高的循环性能。蒸发温度和气体冷却器出口温度两工况的变化对该系统性能的影响程度相对较大。在较低蒸发温度下,该系统可以明显降低压缩机出口温度,有利于系统稳定运行。     

Thermo-environmental analysis of a new molten carbonate fuel cell-based tri-generation plant using stirling engine,generator absorber exchanger and vapour absorption refrigeration: A comparative study

This study aims to present a novel tri-generation plant consisting of a molten carbonate fuel cell (MCFC) unit coupled with a Stirling engine (SE), a heat recovery steam generator (HRSG), and two types of absorption refrigeration cycles (ARCs), i.e., Generator Absorber eXchanger (GAX) and Vapour Absorption Refrigeration (VAR). The proposed system is evaluated from energy, exergy, as well as environmental impact (3E) points of view. To carry out the parametric study, three sub-models are also introduced for the whole system. The sub-model (1) investigates the solo MCFC with the new configuration. In the sub-model (2), the SE and HRSG are added to boost the power generation and overall system efficiency through employing the heat wasted in the sub-model (1). In the last sub-model, for cooling purposes, the surplus heat of MCFC is reutilized using an absorption refrigeration cycle. Besides, to make a comparative study between GAX and VAR systems, the sub-model (3) is classified into two different schemes: (a) with a VAR cycle, and (b) with a GAX cycle. The results reveal that the exergy efficiency and CO₂ emissions of the sub-models (1), (2), and (3) are 48.04%, 51.24%, 52.35% (VAR cycle), 52.12% (GAX cycle), 0.388 t/MWh, 0.364 t/MWh, 0.357 t/MWh (VAR cycle), and 0.358 t/MWh (GAX cycle), respectively. Either with GAX or VAR cycle, the proposed system indicates an acceptable standard of functionality in thermodynamic and environmental perspectives.     

Exergy analysis of an integrated solid oxide fuel cell and organic Rankine cycle for cooling, heating and power production

The study examines a novel system that combined a solid oxide fuel cell (SOFC) and an organic Rankine cycle (ORC) for cooling, heating and power production (trigeneration) through exergy analysis. The system consists of an SOFC, an ORC, a heat exchanger and a single-effect absorption chiller. The system is modeled to produce a net electricity of around 500 kW. The study reveals that there is 3-25% gain on exergy efficiency when trigeneration is used compared with the power cycle only. Also, the study shows that as the current density of the SOFC increases, the exergy efficiencies of power cycle, cooling cogeneration, heating cogeneration and trigeneration decreases. In addition, it was shown that the effect of changing the turbine inlet pressure and ORC pump inlet temperature are insignificant on the exergy efficiencies of the power cycle, cooling cogeneration, heating cogeneration and trigeneration. Also, the study reveals that the significant sources of exergy destruction are the ORC evaporator, air heat exchanger at the SOFC inlet and heating process heat exchanger.     

A new combined cooling, heating and power system driven by solar energy

A new combined cooling, heating and power (CCHP) system is proposed. This system is driven by solar energy, which is different from the current CCHP systems with gas turbine or engine as prime movers. This system combines a Rankine cycle and an ejector refrigeration cycle, which could produce cooling output, heating output and power output simultaneously. The effects of hour angle and the slope angle of the aperture plane for the solar collectors on the system performance are examined. Parametric optimization is conducted by means of genetic algorithm (GA) to find the maximum exergy efficiency. It is shown that the optimal slope angle of the aperture plane for the solar collectors is 60° at 10 a.m. on June 12, and the CCHP system can reach its optimal performance with the slope angle of 45° for the aperture plane at midday. It is also shown that the system can reach the maximum exergy efficiency of 60.33% under the conditions of the optimal slope angle and hour angle.