Impact of hydrogen energy storage on California electric power system: Towards 100% renewable electricity

Decarbonization of the power sector is a key step towards greenhouse gas emissions reduction. Due to the intermittent nature of major renewable sources like wind and solar, storage technologies will be critical in the future power grid to accommodate fluctuating generation. The storage systems will need to decouple supply and demand by shifting electrical energy on many different time scales (hourly, daily, and seasonally). Power-to-Gas can contribute on all of these time scales by producing hydrogen via electrolysis during times of excess electrical generation, and generating power with high-efficiency systems like fuel cells when wind and solar are not sufficiently available. Despite lower immediate round-trip efficiency compared to most battery storage systems, the combination of devices used in Power-to-Gas allows independent scaling of power and energy capacities to enable massive and long duration storage. This study develops and applies a model to simulate the power system balance at very high penetration of renewables. Novelty of the study is the assessment of hydrogen as the primary storage means for balancing energy supply and demand on a large scale: the California power system is analyzed to estimate the needs for electrolyzer and fuel cell systems in 100% renewable scenarios driven by large additions of wind and solar capacities. Results show that the transition requires a massive increase in both generation and storage installations, e.g., a combination of 94 GW of solar PV, 40 GW of wind, and 77 GW of electrolysis systems. A mix of generation technologies appears to reduce the total required capacities with respect to wind-dominated or solar-dominated cases. Hydrogen storage capacity needs are also evaluated and possible alternatives are discussed, including a comparison with battery storage systems.     

Sustainable energy planning based on a stand-alone hybrid renewableenergy/hydrogen power system: Application in Karpathos island, Greece

This study presents the sustainable planning of a renewables-based energy system, which aims to fulfil the electric needs of the island by replacing the existing diesel generators with new wind farms, photovoltaic installations and hydrogen production systems. Electric system design and least cost planning analysis were concluded using historic data from both demand and supply sides. An optimal “sustainable island” scheme should ensure 100% use of renewable energy resources for power generation, while hydrogen production is ideal for covering storage and transportation needs. Due to its morphology and scale, Karpathos applies perfectly for wind and solar energy systems, due to increased solar resource (about 1790 kWh/m².year of global irradiation) and high wind potential (average of 9 m/s in specific locations). Therefore, this case study examines an increase in RES penetration up to 20% in the electric energy mixture, a hydrogen production plan just for the needs of transport and a more aggressive, 100% renewables scheme that ensures a self-fulfilling energy system based on indigenous renewable resources.     

Off-grid hybrid renewable energy system with hydrogen storage for South African rural community health clinic

Most inhabitants of rural communities in Africa lack access to clean and reliable electricity. This has deprived the rural dwellers access to modern healthcare delivery. In this paper, an off-grid renewable energy system consisting of solar PV and wind turbine with hydrogen storage scheme has been explored to meet the electrical energy demands of a health clinic. The health clinic proposed is a group II with 10 beds located in a typical village in South Africa. First, the wind and solar energy resources of the village were analysed. Thereafter, the microgrid architecture that would meet the energy demand of the clinic (18.67 kWh/day) was determined. Some of the key results reveal that the average annual wind speed at 60 m anemometer height and solar irradiation of the village are 7.9 m/s and 4.779 kWh/m²/day, respectively. The required architecture for the clinic composes of 40 kW solar PV system, 3 numbers of 10 kW wind turbines, 8.6 kW fuel cell, 25 kW electrolyser and 40 kg hydrogen tank capacity. The capital cost of the microgrid was found to be $177,600 with a net present cost of $206,323. The levelised cost of energy of the system was determined to be 2.34 $/kWh. The project has a breakeven grid extension distance of 8.81 km. Since this distance is less than the nearest grid extension distance of 21.35 km, it is established that the proposed renewable energy microgrid with a hydrogen storage system is a viable option for the rural community health clinic.     

Production of hydrogen for export from wind and solar energy,natural gas,and coal in Australia

Hydrogen production for export to Japan and Korea is increasingly popular in Australia. The theoretically possible paths include the use of the excess wind and solar energy supply to the grid to produce hydrogen from natural gas or coal. As a contribution to this debate, here I discuss the present contribution of wind and solar to the electricity grid, how this contribution might be expanded to make a grid wind and solar only, what is the energy storage needed to permit this supply, and what is the ratio of domestic total primary energy supply to electricity use. These factors are required to determine the likeliness of producing hydrogen for export. The wind and solar energy capacity, presently at 6.7 and 11.4 GW, have to increase almost 8 times up to values of 53 and 90 GW respectively to support a wind and solar energy only electricity grid for the southeast states only. Additionally, it is necessary to build-up energy storage of actual power >50 GW and stored energy >3000 GW h to stabilize the grid. If the other states and territories are considered, and also the total primary energy supply (TPES) rather than just electricity, the wind and solar capacity must be increased of a further 6–8 times. It is concluded that it is extremely unlikely that hydrogen for export could be produced from the splitting of the water molecule by using excess wind and solar energy, and it is very unlikely that wind and solar may fully cover the local TPES needs. The most likely scenario is production hydrogen via syngas from either natural gas or coal. Production from natural gas and coal needs further development of techniques, to include CO₂ capture, a way to reuse or store CO₂, and finally, the better energy efficiency of the conversion processes. There are several challenges for using natural gas or coal to produce hydrogen with near-zero greenhouse gas emissions. Carbon capture, utilization, and storage technologies that ensure no CO₂ is released in the production process, and new technologies to separate the oxygen from the air, and in case of natural gas, the water, and the CO₂ from the combustion products, are urgently needed to make sense of the fossil fuel hydrogen production. There is no benefit from producing hydrogen from fossil fuels without addressing the CO₂ issue, as well as the fuel energy penalty issue during conversion, that is simply translating in a net loss of fuel energy with the same CO₂ emission.     

Power management strategies for a stand-alone power system using renewable energy sources and hydrogen storage

A stand-alone power system based on a photovoltaic array and wind generators that stores the excessive energy from renewable energy sources (RES) in the form of hydrogen via water electrolysis for future use in a polymer electrolyte membrane (PEM) fuel cell is currently in operation at Neo Olvio of Xanthi, Greece. Efficient power management strategies (PMSs) for the system have been developed. The PMSs have been assessed on their capacity to meet the power load requirements through effective utilization of the electrolyzer and fuel cell under variable energy generation from RES (solar and wind). The evaluation of the PMS has been performed through simulated experiments with anticipated conditions over a typical four-month time period for the region of installation. The key decision factors for the PMSs are the level of the power provided by the RES and the state of charge (SOC) of the accumulator. Therefore, the operating policies for the hydrogen production via water electrolysis and the hydrogen consumption at the fuel cell depend on the excess or shortage of power from the RES and the level of SOC. A parametric sensitivity analysis investigates the influence of major operating variables for the PMSs such as the minimum SOC level and the operating characteristics of the electrolyzer and the fuel cell in the performance of the integrated system.     

Design and analysis of an integrated concentrated solar and wind energy system with storage

This study analyzes a renewable energy‐driven innovative multigeneration system, in which wind and solar energy sources are utilized in an efficient way to generate several useful commodities such as hydrogen, oxygen, desalted water, space cooling, and space heating along with electricity. A 1‐km² heliostat field is considered to concentrate the solar light onto a spectrum splitter, where the light spectrum is separated into two portions as reflected and transmitted to be used as the energy source in the concentrated solar power (CSP) and concentrated photovoltaics (CPV) receivers, respectively. As such, CSP and CPV systems are integrated. Wind energy is proposed for generating electricity (146 MW) or thermal energy (138 MW) to compensate the energy need of the multigeneration system when there is insufficient solar energy. In addition, multiple commodities, 46 MW of electricity, 12 m³/h of desalted water, and 69 MW of cooling, are generated using the Rankine cycle and the rejected heat from its condenser. Further, the heat generated on CPV cells is recovered for efficient photovoltaic conversion and utilized in the space heating (34 MW) and proton exchange membrane (PEM) electrolyzer (239 kg/h) for hydrogen production. The energy and exergy efficiencies of the overall system are calculated as 61.3% and 47.8%, respectively. The exergy destruction rates of the main components are presented to identify the potential improvements of the system. Finally, parametric studies are performed to analyze the effect of changing parameters on the exergy destruction rates, production rates, and efficiencies.     

Hydrogen production probability distributions for a PV-electrolyser system

In this study, we comprehensively analyze the probability distribution of the hydrogen production for PV assisted PEM electrolyser system. A case study is conducted using the experimental data taken from a recently installed system in Balikesir University, Turkey. A novel computational tool is developed in Matlab-Simulink for analyzing the data. The concept of probability density frequency is successfully applied in the analyses of the wind speed and the solar energy in literature. This study presents a method of applying this knowledge to solar energy assisted hydrogen production. The change in the probability distribution of the hydrogen production with the solar irradiation throughout a year is studied and illustrated. It is found that the maximum amount of hydrogen production occurs at between 600 and 650 W/m² of solar radiation. Annual hydrogen production is determined as 2.97 kg for per m² of PV system. Average hydrogen production efficiency of the studied PEM electrolyser is found to be 60.5% with 0.48 A/cm² of current density. The presented results of this study are expected to be valuable for the researchers working on renewable hydrogen production systems.     

Solar hydrogen production in urban areas of Mexico: towards hydrogen cities

Many efforts have been made to assess the potential of green hydrogen production at global, regional, and national levels using Geographic Information Systems (GIS); however, many dismiss the possibility of producing hydrogen in urban settlements. In order to reveal the true potential of these areas, it is essential to provide arguments that allow evaluation of the feasibility of promoting and impulsing the concept of hydrogen cities. Based on this idea, this work assesses the monthly and annual potential of solar hydrogen in urban areas of Mexico using actual measurements of sunshine duration as electrolyzer production times. Moreover, as light transportation is crucial for cities, we examine the substitution of gasoline with hydrogen and its cost throughout the year. These constitute the main contribution of the present work.This study departs from the geographical and technical potential of solar energy, and by using GIS, the amount of hydrogen production per unit of area (Ton/(km² year)) was computed. The levelized cost of hydrogen production (LCOH) is also evaluated, using two of the most popular and commercial electrolysis technologies: PEM and Alkaline.Our results revealed that Mexican urban areas have a high potential to produce solar hydrogen, having an average annual production that varies from 1991.8 Ton/km² to 4338.3 Ton/km² according to the region. The total solar hydrogen potential of all Mexican urban places is 9.39 MTon/year, which could satisfy up to 42.6 times the 2020 hydrogen demand of Mexico. We found that the national gasoline consumption could be replaced by H₂, requiring between 42% and 52% of the total urban production.Additionally, the national average of LCOH was found to be about 6.25 USD/kg for alkaline electrolyzer and 9.50 USD/kg for PEM technology, considering the yearly average sunshine duration of 3237 h/year, which means that Mexico could be competitive at large-scale hydrogen production by using Alkaline technology. Our findings have the potential to impact positively on the country since they provide information to facilitate the derivation of public policies from a rigorous and technical perspective.     

An analysis of hydrogen production from renewable electricity sources

Three aspects of producing hydrogen via renewable electricity sources are analyzed to determine the potential for solar and wind hydrogen production pathways: a renewable hydrogen resource assessment, a cost analysis of hydrogen production via electrolysis, and the annual energy requirements of producing hydrogen for refueling. The results indicate that ample resources exist to produce transportation fuel from wind and solar power. However, hydrogen prices are highly dependent on electricity prices. For renewables to produce hydrogen at $2 kg⁻¹, using electrolyzers available in 2004, electricity prices would have to be less than $0.01 kWh⁻¹. Additionally, energy requirements for hydrogen refueling stations are in excess of 20 GWh/year. It may be challenging for dedicated renewable systems at the filling station to meet such requirements. Therefore, while plentiful resources exist to provide clean electricity for the production of hydrogen for transportation fuel, challenges remain to identify optimum economic and technical configurations to provide renewable energy to distributed hydrogen refueling stations.     

Techno-economic analysis for clean hydrogen production using solar energy under varied climate conditions

The paper discusses the feasibility of the use solar energy into hydrogen production using a photovoltaic energy system in the four main cities of Iraq. An off-grid photovoltaic system with a capacity of 22.0 kWp, an 8.0 kW alkaline electrolyser, a hydrogen compressor, and a hydrogen tank were simulated for one year in order to generate hydrogen. A mathematical model of the proposed system behavior is presented using MATLAB/Simulink, considering nine years from the 2021 to 2030 project span using hourly experimental weather data. The outcomes demonstrated that the annual hydrogen production ranged from 1713.92 kg up to 1891.12 kg, oxygen production ranged from 1199.74 to 1323.78 kg, and water consumption ranged from 7139.91 L to 7877.29 L. The hydrogen evaluated costs equal to $3.79/kg. The results show that the optimum site for solar hydrogen production systems can be established in the midwest of Iraq and in other cities with similar climates, especially those that get a lot of sunlight.     

Hydrogen supply scenarios for a climate neutral energy system in Germany

A climate neutral energy system in Germany will most likely require green hydrogen. Two important factors, that determine whether the hydrogen will be imported or produced locally from renewable energy are still uncertain though - the import price for green hydrogen and the upper limit for photovoltaic installations. To investigate the impact of these two factors, the authors calculate cost optimized climate neutral energy systems while varying the import price from 1.25 €/kg to 5 €/kg with unlimited import volume and the photovoltaic limit from 300 GW to unlimited. In all scenarios, hydrogen plays a significant role. At a medium import price of 3.75 €/kg and photovoltaic limits of 300–900 GW the hydrogen supply is around 1200 to 1300 TWh with import shares varying from 60 to 85%. In most scenarios the electrolysis profile is highly correlated with the photovoltaic power, which leads to full load hours of 1870 h–2770 h.     

Assessing green energy growth in Nepal with a hydropower-hydrogen integrated power grid model

The involvement of green hydrogen in energy transformation is getting global attention. This assessment examines the hydrogen production and its utilization potential in one of the hydropower-rich regions, Nepal under various demand growth and technology intervention scenarios by developing a power grid model of 52 nodes and 68 transmission lines operating at an hourly time-step. The model incorporates a grid-connected hydrogen storage system as well as charging stations for electric and hydrogen vehicles. The least-costly pathways for power grid expansion at the nodal and provincial levels are identified through optimization. The results show that 32 GW of installed capacity is required to meet domestic electricity demand and 14 GW more hydropower should be exploited to completely decarbonize the transport sector by 2050. For maintaining 50% shares of hydrogen vehicle in the transport sector and meet government electricity export targets, Nepal requires 5.7 GW, 12 GW and 23 GW of the additional electrolyzer, hydrogen storage tanks and storage-based hydropower capacities respectively. For a given electricity demand, introducing hydrogen systems can reduce the capacity requirements of hydro storage by storing surplus power generated from pondage run-of-the-river and run-of-the-river hydropower during the rainy season and using it in the dry season.     

Utilization of renewable hybrid energy for refueling station in Al-Kharj,Saudi Arabia

Hydrogen is one of the energy carriers that can be produced using different techniques. Combining multiple energy sources can enhance hydrogen production and meet other electrical demands. The hybrid arrangement allows the produced hydrogen to be stored and used when the electrical energy sources are not adequate. In this study, utilizing the meteorological data was investigated using HOMER (Hybrid Optimization of Multiple Energy Resources) software for the optimal solution. The results demonstrated that the “best-optimized system has 270 kW of photovoltaic (PV), 1 unit of 300 kW of wind turbine (WT), 500 kW of electrolyzer, 100 kg/L of the hydrogen tank, 70 units of 1 kWh lithium-ion battery, and 472 kW of the converter. The selected hybrid energy system has the lowest Levelized cost of energy (LCOE), Levelized cost of hydrogen (LCOH), and net present cost (NPC) of $/kg 0.6208, $/kg 9.34, and $ 484,360.00 respectively which judged the system to be the best choice for the proposed hydrogen project in AI-Kharj. This investigation will help stakeholders and policymakers optimize hybrid energy systems that economically meet the hydrogen production and refueling station demands of the AI-Kharj community.     

Hydrogen generation from small-scale wind-powered electrolysis system in different power matching modes

This study presents a techno-economic evaluation on hydrogen generation from a small-scale wind-powered electrolysis system in different power matching modes. For the analysis, wind speed data, which measured as hourly time series in Kirklareli, Turkey, were used to predict the electrical energy and hydrogen produced by the wind–hydrogen energy system and their variation according to the height of the wind turbine. The system considered in this study is primarily consisted of a 6 kW wind-energy conversion system and a 2 kW PEM electrolyzer. The calculation of energy production was made by means of the levelized cost method by considering two different systems that are the grid-independent system and the grid-integrated system. Annual production of electrical energy and hydrogen was calculated as 15,148.26 kWh/year and 102.37 kg/year, respectively. The highest hydrogen production is obtained in January. The analyses showed that both electrical energy and hydrogen production depend strongly on the hub height of wind turbine in addition to the economic indicators. In the grid-integrated system, the calculated levelized cost of hydrogen changes in the range of 0.3485–4.4849 US$/kg for 36 m hub height related to the specific turbine cost. The grid-integrated system can be considered as profitable when the excess electrical energy delivered by system sold to the grid.     

Assessment of hydrogen production from waste heat using hybrid systems of Rankine cycle with proton exchange membrane/solid oxide electrolyzer

A techno-economic assessment of hydrogen production from waste heat using a proton exchange membrane (PEM) electrolyzer and solid oxide electrolyzer cell (SOEC) integrated separately with the Rankine cycle via two different hybrid systems is investigated. The two systems run via three available cement waste heats of temperatures 360 °C, 432 °C, and 780 °C with the same energy input. The waste heat is used to run the Rankine cycle for the power production required for the PEM electrolyzer system, while in the case of SOEC, a portion of waste heat energy is used to supply the electrolyzer with the necessary steam. Firstly, the best parameters; Rankine working fluid for the two systems and inlet water flow rate and bleeding ratio for the SOEC system are selected. Then, the performance of the two systems (Rankine efficiency, total system efficiency, hydrogen production rate, and economic and CO₂ reduction) is investigated and compared. The results reveal that the two systems' performance is higher in the case of steam Rankine than organic, while a bleeding ratio of 1% is the best condition for the SOEC system. Rankine output power, total system efficiency, and hydrogen production rate rose with increasing waste heat temperature having the same energy. SOEC system produces higher hydrogen production and efficiency than the PEM system for all input waste heat conditions. SOEC can produce 36.9 kg/h of hydrogen with a total system efficiency of 23.8% at 780 °C compared with 27.4 kg/h and 14.45%, respectively, for the PEM system. The minimum hydrogen production cost of SOEC and PEM systems is 0.88 $/kg and 1.55 $/kg, respectively. The introduced systems reduce CO₂ emissions annually by about 3077 tons.     

Analysis of the wind energy market in Denmark and future interactions with an emerging hydrogen market

The transition from fossil fuels to renewable energy sources is critical to reduce future emissions and mitigate the consequences hereof. Yet, the expansion of renewable energy, especially the highly fluctuating production of wind energy, poses economic challenges to the existing energy system in Denmark. This paper investigates the economic feasibility of integrating a 250 kW, 500 kW, 750 kW and 1 MW water electrolysis system in the existing Danish energy market to exploit excessive off- and onshore wind energy for hydrogen production used as fuel for transportation purposes. In 2018, Danish wind turbines produced excess energy during 1238 h, which poses a capacity constraint as the electrolysis systems are limited to only produce hydrogen for 14% of the total available annual hours. This paper concludes that the net present value of each investment is negative as the fixed and variable production costs exceeds the generated revenues and it is therefore not economical feasible to invest in an electrolysis system with the purpose of only operating whenever excess off- and onshore wind energy is available.     

Two energy system analysis models: A comparison of methodologies and results

This paper presents a comparative study of two energy system analysis models both designed for the purpose of analysing electricity systems with a substantial share of fluctuating renewable energy. The first model (EnergyPLAN) has been designed for national and regional analyses. It has been used in the design of strategies for integration of wind power and other fluctuating renewable energy sources into the future energy supply. The model has been used for investigating new operation strategies and investments in flexibility in order to utilize wind power and avoid excess production. The other model (H₂RES) has been designed for simulating the integration of renewable sources and hydrogen into island energy systems. The H₂RES model can use wind, solar and hydro as renewable energy sources and diesel blocks as backup. The latest version of the H₂RES model has an integrated grid connection with the mainland. The H₂RES model was tested on the power system of Porto Santo Island, Madeira, Portugal, Corvo and Graciosa Islands, Azores Islands, Portugal and Sal Island, Cape Verde. This paper presents the results of using the two different models on the same case, the island of Mljet, Croatia. The paper compares methodologies and results with the purpose of identifying mutual benefits and improvements of both models.     

An investigation of optimum PV and wind energy system capacities for alternate short and long‐term energy storage sizing methodologies

The goal of this study is to find the optimal sizes of renewable energy systems (RES) based on photovoltaic (PV) and/or wind systems for three energy storage system (ESS) scenarios in a micro‐grid; (1) with pumped hydro storage (PHS) as a long‐term ESS, (2) with batteries as a short‐term ESS, and (3) without ESS. The PV and wind sizes are optimally determined to accomplish the maximum annual RES fraction (F_RES ) with electricity cost lower than or equal to the utility tariff. Furthermore, the effect of the use of battery and PHS on the electricity cost and F_RES are studied. A university campus on a Mediterranean island is selected as a case study. The results show that PV‐wind hybrid system of 8 MW wind and 4.2 MW PV with 89.5 MWh PHS has the highest F_RES of 88.0%, and the highest demand supply fraction as 42.6%. Moreover, the results indicate that the economic and technical parameters of RESs are affected significantly by the use of ESSs depending on the type and the capacity of both the RES and the ESS.     

Design and analysis of stand-alone hydrogen energy systems with different renewable sources

One of the most interesting developments of energy systems based on the utilization of hydrogen is their integration with renewable sources of energy (RES). In fact, hydrogen can operate as a storage and carrying medium of these primary sources. The design and operation of the system could change noticeably, depending on the type and availability of the primary source. In this paper, the results obtained considering a model of a stand-alone energy system supplied just with RES and composed by an electrolyzer, a hydrogen tank and a proton exchange membrane fuel cell are exposed. The energy systems have been designed in order to supply the electricity needs of a residential user in a mountain environment in Italy during a complete year. Three different sources have been considered: solar irradiance (transformed by an array of photovoltaic modules), hydraulic energy (transformed by a micro-hydro turbine in open-flume configuration) and wind speed (transformed by a small-size wind generator). It has been checked that, in that specific location, it is absolutely not convenient to use the wind source; the solar irradiance has a nearly constant availability during the year, and therefore the seasonal storage of the RES in form of hydrogen is the lowest; the availability of the micro-hydro source is less constant than in case of solar irradiance, requiring a higher hydrogen seasonal storage, but its advantage is linked to the higher efficiency of the turbine and the fact that the RES is directly sent to the user with high frequency (for these reasons it is the best plant option).     

Techno-economic calculation of green hydrogen production and export from Colombia

In the present paper a techno-economic hydrogen production and transportation costs to export from Colombia to Europe and Asia were determined using the open-source Python tools, such as WindPowerLIB, PVLIB, ERA5 weather data, and the Hydrogen-2-Central (H2C) model. Calculations were performed as well for Chile, for comparison as a regional competitor. In addition, a detailed overview of Colombia's energy system and national efforts for a market ramp-up of renewable energy and hydrogen is provided. The application of the model in different scenarios shows Colombia's potential to produce green hydrogen using renewable energies. The prices estimated are 1.5 and 1.02 USD/kgH₂ for 2030 and 2050 with wind power, and 3.24 and 1.65 USD/kgH₂ for 2030 and 2050 using solar energy. Colombia can become one of the most promising hydrogen suppliers to Asian and European countries with one of the lowest prices in the production and transportation of green hydrogen.