Influence of nanofluid on heat transfer in a loop heat pipe

Experiments are conducted to investigate heat transfer characteristics of using nanofluid in a Loop Heat Pipe (LHP) as a working medium for heat input range from 20 W to 100 W. The experiments are carried out by manufacturing the LHP, in which the setup consists of a water tank with pump, a flat evaporator, condenser installed with two pieces of fans, two transportation lines (vapor and liquid lines), copper pipe sections for attachment of the thermocouples and power supply. The uniqueness of the current experimental setup is the vapor and liquid lines of LHP which are made of transparent plastic tube to visualize the fluid flow patterns. In this study, the LHP performance using silica (SiO₂–H₂O) nanofluid with particle volume fraction of 3% which was used as a coolant is examined. The experimental results are verified by simulation using Finite Element Method (FEM). The LHP performance is evaluated in terms of transient temperature distribution and total thermal resistance (R_t). R_t is estimated for both LHP using SiO₂–H₂O nanofluid and pure water cases under a steady state condition. The results reveal the average decrease of 28%–44% at heat input ranging from 20 W to 100 W in total thermal resistance of LHP using SiO₂–H₂O nanofluid as compared with pure water. Therefore, the presence of nanoparticles could greatly enhance the cooling of LHP. The experimental and simulation results are found in good agreement.     

The impact of various nanofluid types on triangular microchannels heat sink cooling performance

This paper discusses the impact of using various types of nanofluids on heat transfer and fluid flow characteristics in triangular shaped microchannel heat sink (MCHS). In this study, an aluminum MCHS performance is examined using water as a base fluid with different types of nanofluids such as Al₂O₃, Ag, CuO, diamond, SiO₂, and TiO₂ as the coolants with nanoparticle volume fraction of 2%. The three-dimensional steady, laminar flow and heat transfer governing equations are solved using the finite volume method. It is inferred that diamond-H₂O nanofluid has the lowest temperature and the highest heat transfer coefficient, while Al₂O₃-H₂O nanofluid has the highest temperature and the lowest heat transfer coefficient. SiO₂-H₂O nanofluid has the highest pressure drop and wall shear stress while Ag-H₂O nanofluid has the lowest pressure drop and wall shear stress among other nanofluid types. Based on the presented results, diamond-H₂O and Ag-H₂O nanofluids are recommended to achieve overall heat transfer enhancement and low pressure drop, respectively, compared with pure water.     

Numerical Simulation of the Thermal Performance of a Nanofluid-Filled Heat Pipe

Improving the working fluid transport properties is a way to enhance the thermal performance of heat transfer equipment. In this research work, a two-dimensional numerical simulation is used to investigate the thermal performance of a nanofluid-filled cylindrical heat pipe. The considered nanofluid is pure water as the base fluid with dispersed Al₂O₃ nanoparticles. Effects of particle volume fractions, particle diameters, various heat inputs, and wick structures on thermal performance of the heat pipe are investigated and the results are compared with that of the pure water. A comparison is made for the first time between the results of a simulation by considering fluid flow in the liquid-wick region and treating this region as pure conduction. The results show the heat pipe thermal performance enhancement and a decrease in thermal resistance for about 31% when 5% particle volume fraction with a particle diameter of 10 nm is used. Also, an insignificant effect of heat input on thermal resistance and variation of pressure distribution in the presence of nanoparticles are observed.     

Thermal Performance Enhancement of L-Shaped Microgrooved Heat Pipe Containing Water-Based Al2O3 Nanofluids

An experimental study was performed to investigate the thermal performance of an L-shaped grooved heat pipe with cylindrical cross section, which contained 0.5 wt% water-based Al₂O₃ nanofluid as the working fluid. The transient performance of the heat pipe and the effect of cooling water temperature on the heat transfer characteristics of the heat pipe were investigated. The outer diameter and the length of the heat pipe were 6 mm and 220 mm, respectively. Experimental results revealed that the temperature of the cooling water has a significant effect on the thermal resistance of the heat pipe containing nanofluids as its working fluid. By increasing the cooling water temperature from 5°C to 27.5°C, the thermal resistance decreases by approximately 40%. At the same charge volume, test results indicated an average reduction of 30% in thermal resistance of heat pipes with nanofluid as compared with heat pipe containing pure water. For transient conditions, unsteady state time for nanofluids was reduced by approximately 28%, when compared with water as the working fluid.     

Heat transfer in rectangular microchannels heat sink using nanofluids

The effect of using nanofluids on heat transfer and fluid flow characteristics in rectangular shaped microchannel heat sink (MCHS) is numerically investigated for Reynolds number range of 100–1000. In this study, the MCHS performance using alumina–water (Al₂O₃-H₂O) nanofluid with volume fraction ranged from 1% to 5% was used as a coolant is examined. The three-dimensional steady, laminar flow and heat transfer governing equations are solved using finite volume method. The MCHS performance is evaluated in terms of temperature profile, heat transfer coefficient, pressure drop, friction factor, wall shear stress and thermal resistance. The results reveal that when the volume fraction of nanoparticles is increased under the extreme heat flux, both the heat transfer coefficient and wall shear stress are increased while the thermal resistance of the MCHS is decreased. However, nanofluid with volume fraction of 5% could not be able to enhance the heat transfer or performing almost the same result as pure water. Therefore, the presence of nanoparticles could enhance the cooling of MCHS under the extreme heat flux conditions with the optimum value of nanoparticles. Only a slight increase in the pressure drop across the MCHS is found compared with the pure water-cooled MCHS.     

Experimental comparative study of heat pipe performance using CuO and TiO2 nanofluids

In recent years, developing an energy efficient conventional heat pipe is more important because of the development of electronics and computer industries. To enhance the thermal performance of heat pipe, different nanofluids have been widely used. In this paper, an experimental investigation of heat transfer performance of heat pipe has been conducted using three different working fluids such as DI water, CuO nanofluid and TiO₂ nanofluid. The heat pipe used in this study is made up of copper layered with two layers of screen mesh wick for better capillary action. The Parameters considered in this study are heat input, angle of inclination and evaporator fill ratio. The concentration of nanoparticle used in this study is of 1.0 wt.%. From the experimental results, comparisons of thermal performance were made between the heat pipes using various working fluids. Among various fill ratio charged, the heat pipe shows good thermal performance when it is operated at 75% fill ratio for all working fluids. However, the heat pipe operated with CuO nanofluid showed higher results compared with TiO₂ nanofluid and DI water. Copyright © 2013 John Wiley & Sons, Ltd.     

A Feasibility Study About Using SiO2 Nanofluid Screen Mesh Wick Heat Pipe for Cooling of High-Power LEDs

Effective and timely heat removal from high-power light-emitting diodes (LEDs) is crucial to their performance and lifetime. The strategy of using a screen mesh wick heat pipe with SiO₂ nanofluid as the working fluid for LED heat dissipation is comprehensively evaluated. An experimental system is set up to study the heat transfer performance of the heat pipe. The obtained experimental results give optimal conditions/parameters for the heat pipe: 60% charging ratio, 30° incline angle, and 1wt% concentration of the nanofluid. Compared with a heat pipe using the secondary distilled water as the working fluid, the thermal resistance of the heat pipe using the SiO₂ nanofluid as the working fluid is generally reduced by around 35–40% for the investigated heat load range of 1–60 W. Based on an equivalent heat conductivity of the SiO₂ nanofluid heat pipe derived from the experimental results, an Icepak modeling effort for the cooling system of a 60-W LED lamp is then expended. The numerical results show that the temperature of the LED lamp remains low and quite uniform across the LED chip region, indicating the technical feasibility of using this class of heat pipes for cooling of high-power LEDs.     

Heat Transfer and Pressure Drop of Nanofluids in a Microchannel Heat Sink

The aim of this study is to determine the upper limitations of the particle volume fraction for heat transfer performance of TiO₂–water nanofluids in microchannels. Nanofluids were prepared by the addition of TiO₂ metallic nanoparticles into distilled water chosen as base fluid at five different volumetric ratios (0.25%, 0.5%, 1.0%, 1.5%, and 2.0%). The effects of the Reynolds number (100–750) and particle volume fraction at constant microchannel height (200 μm) on heat transfer and pressure drop characteristics were analyzed experimentally. Adding metallic oxide particles with nano dimensions into the base fluid did not cause excessive increase of friction coefficient but provided higher heat transfer than that of pure water. It was also observed that water–TiO₂ nanofluid increased heat transfer up to 2.0 vol%, but heat transfer decreased after 2.0 vol%. Furthermore, the thermal resistance was calculated and it was seen that adding nanoparticles with an average diameter smaller than 25 nm into the base fluid caused the thermal resistance to decrease.     

水基纳米流体在铜丝平板热管中的应用

对使用三种水基纳米流体作为工质的铜丝平板热管的传热特性进行了实验研究.使用的纳米流体分别是平均粒径20 nm的Cu纳米颗粒、平均粒径50 nm的Cu纳米颗粒和平均粒径50 nm的CuO纳米颗粒的水基悬浮液(简称水基20 nm Cu、50 nm Cu、50 nm CuO纳米流体),着重分析了纳米流体种类,纳米颗粒质量分数、运行温度或工作压力对热管传热特性的影响.研究结果表明,使用纳米流体作为工质可以显著提高热管的传热特性;在不同运行温度条件下,不同的纳米流体均在质量分数1.0％时具有最佳传热效果;纳米流体是一种适用于铜丝平板热管的新型工质.     

Numerical Investigation on Conjugate Heat Transfer Performance of Microchannel Using Sphericity-Based Gold and Carbon Nanoparticles

Numerical study has been carried out on the laminar forced convection flow of nanofluids in a wide rectangular microchannel. The flow and heat transfer characteristics of gold and of single-walled carbon (SWCNT) nanofluids are investigated in order to find an efficient and cost-effective heat transfer fluid. The effects of nanoparticle volume concentration and of spherical and cylindrical particulate sizes on the conjugate heat transfer performance of the microchannel are reported. The effective thermal conductivity of a nanofluid is evaluated on the basis of particle sphericity by considering the volume and surface area of the nanoparticles. The average convective heat transfer coefficient increases with increase in Reynolds number and volume concentration. Moreover, sphericity-based thermal conductivity evaluation showed that increasing the length of the SWCNT nanoparticle has significant effect on the heat transfer performance, concluding that axial heat conduction dominates the radial heat conduction within the nanoparticle. The carbon nanofluid is identified as an optimized heat transfer fluid with better heat transfer characteristics in comparison with the gold nanofluid. It also reduces the cost of the working fluid. The variations in the interface temperature between solid and fluid regions are reported for nanofluids with different concentrations at different Reynolds numbers. The diameter and length of the SWCNT nanoparticle show a significant effect on heat transfer characteristics.     

Effect of using nanofluids on efficiency of parabolic trough collectors in solar thermal electric power plants

In this paper, forced convection heat transfer nanofluid flow inside the receiver tube of solar parabolic trough collector is numerically simulated. Computational Fluid Dynamics (CFD) simulations are carried out to study the influence of using nanofluid as heat transfer fluid on thermal efficiency of the solar system. The three-dimensional steady, turbulent flow and heat transfer governing equations are solved using Finite Volume Method (FVM) with the SIMPLEC algorithm. The results show that the numerical simulation are in good agreement with the experimental data. Also, the effect of various nanoparticle volume fraction on thermal and hydrodynamic characteristics of the solar parabolic collector is discussed in details. The results indicate that, using of nanofluid instead of base fluid as a working fluid leads to enhanced heat transfer performance. Furthermore, the results reveal that by increasing of the nanoparticle volume fraction, the average Nusselt number increases.     

Heat transfer characteristics in double tube helical heat exchangers using nanofluids

In the present work a three-dimensional analysis is used to study the heat transfer characteristics of a double-tube helical heat exchangers using nanofluids under laminar flow conditions. CuO and TiO₂ nanoparticles with diameters of 24 nm dispersed in water with volume concentrations of 0.5–3 vol.% are used as the working fluid. The mass flow rate of the nanofluid from the inner tube was kept and the mass flow rate of the water from the annulus was set at either half, full, or double the value. The variations of the nanofluids and water temperatures, heat transfer rates and heat transfer coefficients along inner and outer tubes are shown in the paper. Effects of nanoparticles concentration level and of the Dean number on the heat transfer rates and heat transfer coefficients are presented. The results show that for 2% CuO nanoparticles in water and same mass flow rate in inner tube and annulus, the heat transfer rate of the nanofluid was approximately 14% greater than of pure water and the heat transfer rate of water from annulus than through the inner tube flowing nanofluids was approximately 19% greater than for the case which through the inner and outer tubes flow water. The results also show that the convective heat transfer coefficients of the nanofluids and water increased with increasing of the mass flow rate and with the Dean number. The results have been validated by comparison of simulations with the data computed by empirical equations.     

Heat transfer and entropy generation for laminar forced convection flow of graphene nanoplatelets nanofluids in a horizontal tube

The results are reported of an investigation of the heat transfer characteristics and entropy generation for a graphene nanoplatelets (GNP) nanofluid with specific surface area of 750 m²/g under laminar forced convection conditions inside a circular stainless steel tube subjected to constant wall heat flux. The analysis considers constant velocity flow and a concentration range from 0.025 wt.% to 0.1 wt.%. The impact of the dispersed nanoparticles concentration on thermal properties, convective heat transfer coefficient, thermal performance factor and entropy generation is investigated. An enhancement in thermal conductivity for GNP of between 12% and 28% is observed relative to the case without nanoparticles. The convective heat transfer coefficient for the GNP nanofluid is found to be up to 15% higher than for the base fluid. The heat transfer rate and thermal performance for 0.1 wt.% of GNP nanofluid is found to increase by a factor of up to 1.15. For constant velocity flow, frictional entropy generation increases and thermal entropy generation decreases with increasing nanoparticle concentration. But, the total entropy generation tends to decrease when nanoparticles are added at constant velocity and to decrease when velocity rises. Finally, it is demonstrated that a GNP nanofluid with a concentration between 0.075 wt.% and 0.1 wt.% is more energy efficient than for other concentrations. It appears that GNP nanofluids can function as working fluids in heat transfer applications and provide good alternatives to conventional working fluids in the thermal fluid systems.     

Flat Loop Heat Pipe with Bi-Transport Loops for Graphics Card Cooling

A flat loop heat pipe (FLHP) with bi-transport loops is developed for the cooling of graphics card with high heat flux up to 80W/cm². The evaporator and the pipes are made of copper and ultrapure water (electronic resistivity > 18 MΩ-cm) as the working fluid. To give the loop heat pipe (LHP) better performance, the evaporator is made in a flat shape to reduce the contact resistance between the evaporator and the chip. The advances of the LHP with bi-transport loops are discussed. The heat transfer performance is tested with different filling rate in different orientations. The test results show that the LHP can start up easily and can transport large amount of heat stably. The orientation of the condenser above the evaporator gives a better performance, and filling with 13 g of water gives a better performance. Limited by the evaporator temperature lower than 90°C, the LHP can transport 320 W when the evaporator is above the condenser and 380 W when the condenser is above the evaporator.     

Enhancement of heat and mass transfer characteristics of metal hydride reactor for hydrogen storage using various nanofluids

The execution of metal hydride reactor (MHR) for storage of hydrogen is greatly affected by thermal effects occurred throughout the sorption of hydrogen. In this paper, based on different governing equations, a numerical model of MHR filled by MmNi_4.6Al_0.4 is formed using ANSYS Fluent for hydrogen absorption process. The validation of model is done by relating its simulation outcomes with published experimental results and found a good agreement with a deviation of less than 5%; hence present model accuracy is considered to be more than 95%. For extraction or supply of heat, water or oil is extensively used in MHR during the absorption or the desorption process so as to improve the competency of the system. Since nanofluid (mixture of base fluid and nanoparticles) has a higher heat transfer characteristics, in this paper the nanofluid is used in place of the conventional heat transfer fluid in MHR. Further the numerical model of MHR is modified with nanofluid as heat extraction fluid and results are presented. The Al₂O₃/H₂O, CuO/H₂O and MgO/H₂O nanofluids are selected and simulations are carried out. The results are obtained for different parameters like nanoparticle material, hydrogen concentration, supply pressure and cooling fluid temperature. It is seen that 5 vol% CuO/H₂O nanofluid is thermally superior to Al₂O₃/H₂O and MgO/H₂O nanofluid. The heat transfer rate improves by the increment in the supply pressure of hydrogen as well as decrement in temperature of nanofluid. The CuO/H₂O nanofluid increases the heat transfer rate of MHR up to 10% and the hydrogen absorption time is improved by 9.5%. Thus it is advantageous to use the nanofluid as a heat transfer cooling fluid for the MHR to store hydrogen.     

Performance Analysis of Flat-Plate Solar Collector Having Silver Nanofluid as a Working Fluid

A study on water solar collector performance having silver nanofluid as working fluid was carried out. In this study, 20-nm silver particles mixed with water at the concentrations of 1,000 and 10,000 ppm were undertaken in 3 small identical closed-loop flat-plate solar collectors, each with an area of 0.15 m × 1.0 m. The mass flux of the working fluid varied between 0.8 and 1.2 L/min-m² and the inlet temperatures were controlled in the range of 35–65°C. The tests were performed outdoor under a steady-state condition. The experimental results showed that at the same Reynolds number, the convective heat transfer coefficient of the nanofluid inside the solar absorber tube at 1,000 ppm was slightly higher than that of water, and at 10,000 ppm, the heat transfer coefficient was about 2 times that of water. This meant that the overall heat loss coefficient of the solar collector with nanofluid could be reduced and more solar heat gain could be obtained, especially with a high inlet temperature of the working fluid. In our experiments, for 10,000 ppm concentration of silver nanoparticles, the optical characteristic and the thermal loss characteristic of the solar collector, under steady-state condition with a mass flux of 1.2 kg/min-m², were 0.691 and 4.869 W/m²-K, compared with 0.684 and 7.178 W/m²-K, respectively for 1,000 ppm concentration and 0.702 and 8.318 W/m²-K for water. When the flow rate was different from the standard value, the solar thermal characteristics were also improved with the nanofluid.     

不同加热方式下环路热管蒸发器可视化研究

针对环路热管内部工质相变及流动换热问题,设计了环路热管蒸发器中心通道可视化实验平台,研究了不同加热方式对热管内工质状态和传热特性的影响。结果表明：加热方式直接影响热管10W启动过程,双面加热启动速度最快。相同热载荷时,不同加热方式下环路热管热阻及蒸发器中心通道内液面高度和成核情况存在差异。10W - 40W热载荷时,随着热载荷的增大,三种加热方式的传热热阻均在减小。40W-50W热载荷时,顶部加热方式下的热管性能出现恶化,底部加热传热性能出现停滞,仅双面加热性能稳定并有提高趋势。随着热负荷的增加,蒸发器中心通道内气液界面升高、气泡的产生变得更加剧烈,蒸发器通过吸液芯向储液器的漏热量增加,进而影响环路热管的性能。     

Heat transfer and friction factor of water based TiO2 and SiO2 nanofluids under turbulent flow in a tube

The heat transfer coefficient and friction factor of TiO₂ and SiO₂ water based nanofluids flowing in a circular tube under turbulent flow are investigated experimentally under constant heat flux boundary condition. TiO₂ and SiO₂ nanofluids with an average particle size of 50 nm and 22 nm respectively are used in the working fluid for volume concentrations up to 3.0%. Experiments are conducted at a bulk temperature of 30 °C in the turbulent Reynolds number range of 5000 to 25,000. The enhancements in viscosity and thermal conductivity of TiO₂ are greater than SiO₂ nanofluid. However, a maximum enhancement of 26% in heat transfer coefficients is obtained with TiO₂ nanofluid at 1.0% concentration, while SiO₂ nanofluid gave 33% enhancement at 3.0% concentration. The heat transfer coefficients are lower at all other concentrations. The particle concentration at which the nanofluids give maximum heat transfer has been determined and validated with property enhancement ratio. It is observed that the pressure drop is directly proportional to the density of the nanoparticle.     

Entropy Generation in a Circular Tube Heat Exchanger Using Nanofluids: Effects of Different Modeling Approaches

The main goal of this paper is to compare single- and two-phase modeling approaches for forced convection flow of water/TiO₂ nanofluid. The considered geometry is a horizontal tube with constant wall heat flux boundary condition where flow regime is turbulent. A computational fluid dynamics (CFD) approach is utilized for heat transfer and flow field estimation of the single-phase and three different two-phase approaches, namely, volume of fluid, mixture, and Eulerian models. Results are presented for Reynolds numbers ranging from 9000 to 21,000, for different nanoparticle diameters ranging from 20 to 40 nm, and for values of volume fractions ranging from 0 to 4%. The obtained results show that the values of entropy generation for thermal and turbulent dissipation are very close for the single-phase and mixture models. Numerical investigation showed that the values of entropy production for pure water are identical regardless of the CFD approach; however, when the volume fraction of nanoparticles increases, differences between the models appear.     

Heat transfer enhancement in microchannel heat sinks using nanofluids

Heat transfer enhancement in a 3-D microchannel heat sink (MCHS) using nanofluids is investigated by a numerical study. The addition of nanoparticles to the coolant fluid changes its thermophysical properties in ways that are closely related to the type of nanoparticle, base fluid, particle volume fraction, particle size, and pumping power. The calculations in this work suggest that the best heat transfer enhancement can be obtained by using a system with an Al₂O₃–water nanofluid-cooled MCHS. Moreover, using base fluids with lower dynamic viscosity (such as water) and substrate materials with high thermal conductivity enhance the thermal performance of the MCHS. The results also show that as the particle volume fraction of the nanofluid increases, the thermal resistance first decreases and then increases. The lowest thermal resistance can be obtained by properly adjusting the volume fraction and pumping power under given geometric conditions. For a moderate range of particle sizes, the MCHS yields better performance when nanofluids with smaller nanoparticles are used. Furthermore, the overall thermal resistance of the MCHS is reduced significantly by increasing the pumping power. The heat transfer performance of Al₂O₃–water and diamond–water nanofluids was 21.6% better than that of pure water. The results reported here may facilitate improvements in the thermal performance of MCHSs.