A comparative evaluation of compression ignition engine characteristics using methyl and ethyl esters of Karanja oil

This paper investigates the scope of utilizing biodiesel developed from both through the methyl as well as ethyl alcohol route (methyl and ethyl ester) from Karanja oil as an alternative diesel fuel. The major problem of using neat Karanja oil as a fuel in a compression ignition engine arises due to its very high viscosity. Transesterification with alcohols reduces the viscosity of the oil and other properties have been evaluated to be comparable with those of diesel. In the present work, methyl and ethyl esters of Karanja oil were prepared by transesterification using both methanol and ethanol. The physical and chemical properties of ethyl esters were comparable with that of methyl esters. However, viscosity of ethyl esters was slightly higher than that of methyl esters. Cold flow properties of ethyl esters were better than those of methyl esters. Performance and exhaust emission characteristics of the engine were determined using petrodiesel as the baseline fuel and several blends of diesel and biodiesel as test fuels. Results show that methyl esters produced slightly higher power than ethyl esters. Exhaust emissions of both esters were almost identical. These studies show that both methyl and ethyl esters of Karanja oil can be used as a fuel in compression ignition engine without any engine modification.     

Experimental investigations on combustion, performance and emissions characteristics of neat karanji biodiesel and its methanol blend in a diesel engine

The increased focus on alternative fuels research in the recent years are mainly driven by escalating crude oil prices, stringent emission norms and the concern on clean environment. The processed form of vegetable oil (biodiesel) has emerged as a potential substitute for diesel fuel on account of its renewable source and lesser emissions. The experimental work reported here has been carried out on a turbocharged, direct injection, multi-cylinder truck diesel engine fitted with mechanical distributor type fuel injection pump using biodiesel-methanol blend and neat karanji oil derived biodiesel under constant speed and varying load conditions without altering injection timings. The results of the experimental investigation indicate that the ignition delay for biodiesel-methanol blend is slightly higher as compared to neat biodiesel and the maximum increase is limited to 1 deg. CA. The maximum rate of pressure rise follow a trend of the ignition delay variations at these operating conditions. However, the peak cylinder pressure and peak energy release rate decreases for biodiesel-methanol blend. In general, a delayed start of combustion and lower combustion duration are observed for biodiesel-methanol blend compared to neat biodiesel fuel. A maximum thermal efficiency increase of 4.2% due to 10% methanol addition in the biodiesel is seen at 80% load and 16.67 s⁻¹ engine speed. The unburnt hydrocarbon and carbon monoxide emissions are slightly higher for the methanol blend compared to neat biodiesel at low load conditions whereas at higher load conditions unburnt hydrocarbon emissions are comparable for the two fuels and carbon monoxide emissions decrease significantly for the methanol blend. A significant reduction in nitric oxide and smoke emissions are observed with the biodiesel-methanol blend investigated.     

Progress in biodiesel processing

Biodiesel is a notable alternative to the widely used petroleum-derived diesel fuel since it can be generated by domestic natural sources such as soybeans, rapeseeds, coconuts, and even recycled cooking oil, and thus reduces dependence on diminishing petroleum fuel from foreign sources. The injection and atomization characteristics of the vegetable oils are significantly different than those of petroleum-derived diesel fuels, mainly as the result of their high viscosities. Modern diesel engines have fuel-injection system that is sensitive to viscosity change. One way to avoid these problems is to reduce fuel viscosity of vegetable oil in order to improve its performance. The conversion of vegetable oils into biodiesel is an effective way to overcome all the problems associated with the vegetable oils. Dilution, micro-emulsification, pyrolysis, and transesterification are the four techniques applied to solve the problems encountered with the high fuel viscosity. Transesterification is the most common method and leads to monoalkyl esters of vegetable oils and fats, now called biodiesel when used for fuel purposes. The methyl ester produced by transesterification of vegetable oil has a high cetane number, low viscosity and improved heating value compared to those of pure vegetable oil which results in shorter ignition delay and longer combustion duration and hence low particulate emissions.     

Biodiesel from cotton seed oil and its effect on engine performance and exhaust emissions

The use of biodiesel is rapidly expanding around the world, making it imperative to fully understand the impacts of biodiesel on the diesel engine combustion process and pollutant formation. Biodiesel is known as the mono-alkyl-esters of long chain fatty acids derived from renewable feedstocks, such as, vegetable oils or animal fats, for use in compression ignition engines. Different parameters for the optimization of biodiesel production were investigated in the first phase of this study, while in the next phase of the study performance test of a diesel engine with neat diesel fuel and biodiesel mixtures were carried out. Biodiesel was made by the well known transesterification process. Cottonseed oil (CSO) was selected for biodiesel production. Cottonseed is non-edible oil, thus food versus fuel conflict will not arise if this is used for biodiesel production. The transesterification results showed that with the variation of catalyst, methanol or ethanol, variation of biodiesel production was realized. However, the optimum conditions for biodiesel production are suggested in this paper. A maximum of 77% biodiesel was produced with 20% methanol in presence of 0.5% sodium hydroxide. The engine experimental results showed that exhaust emissions including carbon monoxide (CO) particulate matter (PM) and smoke emissions were reduced for all biodiesel mixtures. However, a slight increase in oxides of nitrogen (NO_x) emission was experienced for biodiesel mixtures.     

Effect of nanoparticle on emission and performance characteristics of a diesel engine fueled with cashew nut shell biodiesel

High-rise in the air pollution levels due to combustion of the fossil fuel gives us the opportunity to discover environmentally friendly and clean fuels for the engines. Biodiesel originated from cashew nut shell oil through transesterification process can be blended or used as a neat fuel in unmodified engines. This work investigates the effect of alumina nanoparticles on emission and performance characteristics of cashew nut shell biodiesel. Neat cashew nut shell biodiesel prepared by conventional transesterification is termed as BD100 and biodiesel prepared by modified transesterification with the addition of alumina nanoparticles is termed as BD100A. Experimental results on unmodified diesel engine revealed that emission parameters such as CO, HC, NOx, and smoke were decreased by 5.3%, 7.4%, 10.23%, and 16.1% for BD100% and 8.8%, 10.1%, 12.4%, and 18.4% for B100A, respectively, compared to diesel fuel. At full load conditions, compared to diesel fuel, the BTE dropped by 1.1% and 2.3%, whereas the BSFC increased by 3.8% and 5.1% for B100A and B100 correspondingly.     

Hydrogen-enriched palm biodiesel as a potential alternative fuel for diesel engines: Investigating performance and emission characteristics and mitigation strategies for air pollutants

Palm biodiesel is one of the most suitable alternative fuels due to its capability to replace traditional fossil fuel usage in IC engines. Even as palm biodiesel (POBD) reduces harmful pollutant gases, the engine performance is not on an equal scale with neat diesel. To address this shortcoming, an investigation was carried out to examine the application of palm biodiesel (PBD) and hydrogen induction through the intake air at the flow rates of 6 and 8LPM (Litre Per Minute) in the compression ignition (CI) engine. The experimental study shows that POBD has poor engine performance and moderate pollution reduction compared with neat diesel. When compared to POBD and neat diesel, the higher calorific value and other H₂ characteristics improve combustion properties, resulting in higher engine performance and lower pollutant gases (except NOx). When compared to the palm biodiesel blend (BD 30), the results of BD30+8LPM reduced the Specific fuel consumption (SFC) by 0.0885kg/kWh and improved the brake thermal efficiency (BTE) by 6.67%. The Carbon monoxide (CO), hydro carbon (HC), and smoke opacity were reduced by 0.047% volume, 29.2 ppm, and 6.52% respectively. A marginal increase in NOx was seen as 297.6 ppm.     

Production of Biodiesel from Vegetable Oils: A Survey

Abstract

The purpose of this work is to investigate biodiesel production processes from vegetable oils. Biodiesel fuel can be made from new or used vegetable oils and animal fats, which are non-toxic, biodegradable, renewable resources. The vegetable oil fuels were not acceptable because they were more expensive than petroleum fuels. Biodiesel has become more attractive recently because of its environmental benefits. With recent increases in petroleum prices and uncertainties concerning petroleum availability, there is renewed interest in vegetable oil fuels for diesel engines. Dilution of oils with solvents and microemulsions of vegetable oils lowers the viscosity, and some engine performance problems still exist. The purpose of the transesterification process is to lower the viscosity of the oil. Pyrolysis produces more biogasoline than biodiesel fuel.     

Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Performance and emission evaluation of a diesel engine fueled with methyl esters of rubber seed oil

Recent concerns over the environment, increasing fuel prices and scarcity of its supply have promoted the interest in development of the alternative sources for petroleum fuels. At present, biodiesel is commercially produced from the refined edible vegetable oils such as sunflower oil, palm oil and soybean oil, etc. by alkaline-catalyzed esterification process. This process is not suitable for production of biodiesel from many unrefined non-edible vegetable oils because of their high acid value. Hence, a two-step esterification method is developed to produce biodiesel from high FFA vegetable oils. The biodiesel production method consists of acid-catalyzed pretreatment followed by an alkaline-catalyzed transesterification. The important properties of methyl esters of rubber seed oil are compared with other esters and diesel. Pure rubber seed oil, diesel and biodiesel are used as fuels in the compression ignition engine and the performance and emission characteristics of the engine are analyzed. The lower blends of biodiesel increase the brake thermal efficiency and reduce the fuel consumption. The exhaust gas emissions are reduced with increase in biodiesel concentration. The experimental results proved that the use of biodiesel (produced from unrefined rubber seed oil) in compression ignition engines is a viable alternative to diesel.     

Hydroprocessed vegetable oil as a fuel for transportation sector: A review

Renewable fuels produced from vegetable oils are an attractive alternative to fossil-based fuel. Different type of fuels can be derived from these triglycerides. One of them is biodiesel which is a mono alkyl ester of the vegetable oil. The biodiesel is produced by transesterification of the oil with an alcohol in the presence of a catalyst. Another kind of fuel (which is similar to petroleum-derived diesel) can be produced from the vegetable oil using hydroprocessing technique. This method uses elevated temperature and pressure along with a catalyst to produce a fuel termed as ‘renewable diesel’. The fuel produced has properties that are beneficial for the engine as well as the environment. It has high cetane number, low density, excellent cold flow properties and same materials can be used as are used for engine running on petrodiesel. It can effectively reduce NOx, PM, HC, CO emissions and unregulated emissions as well as greenhouse gases as compared to diesel. The fuel is also beneficial for the after-treatment systems. Trials in the field have shown that the volumetric fuel consumption of renewable diesel is higher than petrodiesel and nearly proportional to the volumetric heating value. The present review focuses on the hydroprocessing technique used for the renewable diesel production and the effect of different parameters such as catalyst, reaction temperature, hydrogen pressure, liquid hourly space velocity (LHSV) and H₂/oil ratio on oil conversion, diesel selectivity, and isomerization. The review also summarizes the effect; renewable diesel has on combustion, performance, and emission characteristics of a compression ignition engine.     

Comparison of performance characteristics of agricultural tractor diesel engine operating on home and industrially produced biodiesel

Owing to unstable diesel fuel prices in the world market, many farmers have been looking for alternative fuels. Vegetable oils are one of the alternatives, which can be used as fuel in diesel engines either in the form of straight vegetable oil or in the form of biodiesel. This study aims to present experimental data by utilization of home and industrial biodiesel as fuel in an agricultural tractor diesel engine. The home biodiesel production was made from different vegetable oils (crude rapeseed, edible sunflower and waste oil) with the process of one‐stage‐based catalyzed transesterification. A commercially available agricultural tractor ZETOR 7745 was employed. Measurements were taken on the power take‐off shaft by electrical dynamometer FROMENT XT200. According to the results, agricultural tractor diesel engine operating on home biodiesel fuels had better performance characteristics related to industrially produced biodiesel and similar to conventional diesel fuel. Copyright © 2009 John Wiley & Sons, Ltd.     

车用典型生物燃料的组分及理化特性对比研究

基于特定的原材料和典型的制备工艺,选取废弃油脂生物柴油（WME）、麻风树果生物柴油（JME）和生物裂解燃油（PBF）作为典型的生物燃料,与在用的国Ⅴ标准0^# 石化柴油（PD）进行组分分子结构及组分含量的对比。GC-MS分析结果表明,生物柴油分子碳链长度集中于C₁₆ ~ C₁₈,且不饱和组分含量较高,生物裂解油组分分子碳链长度较为分散,短链组分明显增加,不饱和组分明显降低。四种燃料的理化特性对比分析结果表明,分子碳链长度及不饱和度对燃油的粘度、十六烷值（CN）以及热值等产生综合影响,三种典型生物燃料特别是生物裂解油对石化柴油有着良好的替代性。     

Performance evaluation of a diesel engine fueled with methyl ester of castor seed oil

In this investigation, castor methyl ester (CME) was prepared by transesterification using potassium hydroxide (KOH) as catalyst and was used in four stroke, single cylinder variable compression ratio type diesel engine. Tests were carried out at a rated speed of 1500 rpm at different loads. Straight vegetable oils pose operational and durability problems when subjected to long term usages in diesel engines. These problems are attributed to high viscosity, low volatility and polyunsaturated character of vegetable oils. The process of transesterification is found to be an effective method of reducing vegetable oil viscosity and eliminating operational and durability problems. The important properties of methyl ester of castor seed oil are compared with diesel fuel. The engine performance was analysed with different blends of biodiesel and was compared with mineral diesel. It was concluded that the lower blends of biodiesel increased the break thermal efficiency and reduced the fuel consumption. The exhaust gas temperature increased with increasing biodiesel concentration. The results proved that the use of biodiesel (produced from castor seed oil) in compression ignition engine is a viable alternative to diesel.     

Combustion performance and emission reduction characteristics of automotive DME engine system

This article is a condensed overview of a dimethyl ether (DME) fuel application for a compression ignition diesel engine. In this review article, the spray, atomization, combustion and exhaust emissions characteristics from a DME-fueled engine are described, as well as the fundamental fuel properties including the vapor pressure, kinematic viscosity, cetane number, and the bulk modulus. DME fuel exists as gas phase at atmospheric state and it must be pressurized to supply the liquid DME to fuel injection system. In addition, DME-fueled engine needs the modification of fuel supply and injection system because the low viscosity of DME caused the leakage. Different fuel properties such as low density, viscosity and higher vapor pressure compared to diesel fuel induced the shorter spray tip penetration, wider cone angle, and smaller droplet size than diesel fuel. The ignition of DME fuel in combustion chamber starts in advance compared to diesel or biodiesel fueled compression ignition engine due to higher cetane number than diesel and biodiesel fuels. In addition, DME combustion is soot-free since it has no carbon–carbon bonds, and has lower HC and CO emissions than that of diesel combustion. The NO_x emission from DME-fueled combustion can be reduced by the application of EGR (exhaust gas recirculation). This article also describes various technologies to reduce NO_x emission from DME-fueled engines, such as the multiple injection strategy and premixed combustion. Finally, the development trends of DME-fueled vehicle are described with various experimental results and discussion for fuel properties, spray atomization characteristics, combustion performance, and exhaust emissions characteristics of DME fuel.     

Biodiesel production from vegetable oils via catalytic and non-catalytic supercritical methanol transesterification methods

This paper reviews the production and characterization of biodiesel (BD or B) as well as the experimental work carried out by many researchers in this field. BD fuel is a renewable substitute fuel for petroleum diesel or petrodiesel (PD) fuel made from vegetable or animal fats. BD fuel can be used in any mixture with PD fuel as it has very similar characteristics but it has lower exhaust emissions. BD fuel has better properties than that of PD fuel such as renewable, biodegradable, non-toxic, and essentially free of sulfur and aromatics. There are more than 350 oil bearing crops identified, among which only sunflower, safflower, soybean, cottonseed, rapeseed and peanut oils are considered as potential alternative fuels for diesel engines. The major problem associated with the use of pure vegetable oils as fuels, for Diesel engines are caused by high fuel viscosity in compression ignition. Dilution, micro-emulsification, pyrolysis and transesterification are the four techniques applied to solve the problems encountered with the high fuel viscosity. Dilution of oils with solvents and microemulsions of vegetable oils lowers the viscosity, some engine performance problems still exist. The viscosity values of vegetable oils vary between 27.2 and 53.6 mm²/s whereas those of vegetable oil methyl esters between 3.59 and 4.63 mm²/s. The viscosity values of vegetable oil methyl esters highly decreases after transesterification process. Compared to no. 2 diesel fuel, all of the vegetable oil methyl esters were slightly viscous. The flash point values of vegetable oil methyl esters are highly lower than those of vegetable oils. An increase in density from 860 to 885 kg/m³ for vegetable oil methyl esters or biodiesels increases the viscosity from 3.59 to 4.63 mm²/s and the increases are highly regular. The purpose of the transesterification process is to lower the viscosity of the oil. The transesterfication of triglycerides by methanol, ethanol, propanol and butanol, has proved to be the most promising process. Methanol is the commonly used alcohol in this process, due in part to its low cost. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The most important variables affecting the methyl ester yield during the transesterification reaction are molar ratio of alcohol to vegetable oil and reaction temperature. Biodiesel has become more attractive recently because of its environmental benefits. Biodiesel is an environmentally friendly fuel that can be used in any diesel engine without modification.     

Performance characteristics of a low heat rejection diesel engine operating with biodiesel

Vegetable oils are a promising alternative among the different diesel fuel alternatives. However, the high viscosity, poor volatility and cold flow characteristics of vegetable oils can cause some problems such as injector coking, severe engine deposits, filter gumming, piston ring sticking and thickening of lubrication oil from long-term use in diesel engines. These problems can be eliminated or minimized by transesterification of the vegetable oils to form monoesters. These monoesters are known as biodiesel. The important advantages of biodiesel are lower exhaust gas emissions and its biodegradability and renewability compared with petroleum-based diesel fuel. Although the transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than that of petroleum diesel fuel. The energy of the biodiesel can be released more efficiently with the concept of low heat rejection (LHR) engine. The aim of this study is to apply LHR engine for improving engine performance when biodiesel is used as an alternative fuel. For this purpose, a turbocharged direct injection (DI) diesel engine was converted to a LHR engine and the effects of biodiesel (produced from sunflower oil) usage in the LHR engine on its performance characteristics have been investigated experimentally. The results showed that specific fuel consumption and the brake thermal efficiency were improved and exhaust gas temperature before the turbine inlet was increased for both fuels in the LHR engine.     

Inhibition of NO emission by adding antioxidant mixture in Jatropha biodiesel on the performance and emission characteristics of a C.I. engine

In this paper, the effect of adding an antioxidant mixture in Jatropha biodiesel as fuel, in a single cylinder, direct injection compression ignition engine was experimentally investigated and the level of pollutants in the exhaust and performance characteristics of the engine were analyzed. Nine test fuels were prepared with three antioxidants, namely, Succinimide (C₄H₅NO₂), N,N-dimethyl-p-phenylenediamine-dihydrochloride (C₈H₁₄Cl₂N₂), and N-phenyl-p-phenylenediamine (C₆H₅NHC₆H₄NH₂) added to neat biodiesel at 500 parts per million (ppm), 1000 ppm and 2000 ppm and the observed experimental results were compared with those of neat biodiesel and neat diesel as base fuels. The comparison showed that NO emission was reduced drastically for the test fuels with the antioxidant addition of 2000 ppm. The maximum reduction of 10% of NO emission was observed for the antioxidant mixture in neat biodiesel, with a slight increase in unburned HC, CO and smoke opacity. In addition, the obtained experimental results reveal that the addition of two antioxidants as mixture in neat biodiesel caused improved NO emission reduction for all test fuels.     

Biodiesel production from waste cooking oil using heterogeneous catalysts and its operational characteristics on variable compression ratio CI engine

In the present work, the optimum biodiesel conversion from waste cooking oil to biodiesel through transesterification method was investigated. The base catalyzed transesterification under different reactant proportions such as the molar ratio of alcohol to oil and mass ratio of catalyst to oil was studied for optimum production of biodiesel. The optimum condition for base catalyzed transesterification of waste cooking oil was determined to be 12:1 and 5 wt% of zinc doped calcium oxide. The fuel properties of the produced biodiesel such as the calorific value, flash point and density were examined and compared to conventional diesel. The properties of produced biodiesel and their blend for different ratios (B20, B40, B60, B80 and B100) were comparable with properties of diesel oil and ASTM biodiesel standards. Tests have been conducted on CI engine which runs at a constant speed of 1500 rpm, injection pressure of 200 bar, compression ratio 15:1 and 17.5, and varying engine load. The performance parameters include brake thermal efficiency, brake specific energy consumption and emissions parameters such as Carbon monoxide (CO), Hydrocarbon (HC), Oxides of Nitrogen (NOx) and smoke opacity varying with engine load (BP). Diesel engine's thermal performance and emission parameters such as CO, HC, and NOx on different biodiesel blends demonstrate that biodiesel produced from waste cooking oil using heterogeneous catalyst was suitable to be used as diesel oil blends and had lesser emissions as compared to conventional diesel.     

Study on the spray characteristics of methyl esters from waste cooking oil at elevated temperature

In Taiwan, millions of tons of waste cooking oil are produced each year, and less than 20% of it, about 150,000 ton/a, is reclaimed and reused. Most waste oil is flushed down the drain. Utilizing waste cooking oil to make biodiesel not only reduces engine exhaust gas pollution, but also replaces food-derived fuels, and reduces ecologic river pollution. This study employed two-stage transesterification to lower the high viscosity of waste oil, utilized emulsion to reduce the methyl ester NOx pollution, and used methanol to enhance the stability and viscosity of emulsified fuel. To further analyze spray characteristics of fuels, this experiment built a constant volume bomb under high temperature, used high speed photography to analyze spray tip penetration, spray angle, and the Sauter mean diameter (SMD) of fuel droplets, and compared the results with fossil diesel. The experimental results suggested that, two-stage transesterification can significantly lower waste oil viscosity to that which is close to fossil diesel viscosity. At a temperature above 300 °C, waste cooking oil methyl esters had a water content of 20%, spray droplet characteristics were significantly improved, and NOx emission dropped significantly. The optimal fuel ratio suggested in this experiment was waste cooking oil methyl ester 74.5%, methanol 5%, water 20%, and composite surfactant Span–Tween 0.5%.     

Homogeneous charge compression ignition of binary fuel blends

The present experimental investigation aims to understand the homogeneous combustion chemistry associated with binary blends of three surrogate components for practical fuels, including toluene, isooctane, and diisobutylene-1 (DIB-1). Specifically, high-pressure autoignition characteristics of the three neat fuel components as well as the fuel blends of toluene + isooctane and toluene + DIB-1 are studied herein. Experiments are conducted in a rapid compression machine at compressed pressures varying from 15 to 45 bar and under low to intermediate temperatures. To obtain insights into interactions among fuels, the relative proportion of the two neat fuels in the reactive mixtures is systematically varied, while the total fuel mole fraction and equivalence ratio are kept constant. Experimental results demonstrate that ignition delays for neat toluene are more than an order of magnitude longer than those for neat isooctane. Whereas DIB-1 has ignition delays shorter than those for isooctane at higher temperatures, at temperatures lower than 820 K DIB-1 shows a longer ignition delay. Although the ignition delays of binary blends lie in between the two extremes of neat components, the variation of ignition delay with the relative fuel proportion is seen to be highly nonlinear. Especially, a small addition of isooctane or DIB-1 to toluene can result in greatly enhanced reactivity. In addition, the effect of DIB-1 addition to toluene is more significant than the effect of isooctane addition. Furthermore, in the compressed temperature range from 820 to 880 K, ignition delay of the toluene + isooctane blend shows greater sensitivity to temperature than that of isooctane.