Lift Enhancement and Oscillatory Suppression of Vortex-induced Vibration in Shear Flow by Loentz Force

The flow of the weak electrolyte solution can be controlled by Lorentz force achieved with the suitable magnetic and electric fields, and it has the advantages of vortex street suppression, drag reduction, lift enhancement and oscillatory suppression for the flow over a bluff body. The electro-magnetic control of vortex-induced vibration (VIV) of a circular cylinder in the shear flow was investigated numerically in the exponential-polar coordinates attached on the moving cylinder for Re=150. With the effect of background vorticity, the vortex street of VIV cylinder was composed of two parallel rows with an opposite sign of the vortices which inclines toward the lower side and the strength of upper vortex is larger than that of lower vortex. The lift force vibrated periodically with the effect of vortex shedding and the mean value was negative due to the background vorticity. The Lorentz force for controlling the VIV cylinder was classified into the field Lorentz force and the wall Lorentz force. The field Lorentz force suppresses the lift oscillation, and in turn, suppresses the VIV, whereas the wall Lorentz force increases the lift.     

Research on Electro Hydraulic Proportional Control for Heavy Vehicle Blend Braking System

A blend braking system of heavy vehicle was proposed. The main control part of the system is the electro hydraulic proportional servo valve. A nonlinear model of brake cylinder controlled by the valve was deduced through the analysis of its control property and system feature. The transfer function of the system was also proposed, and the hydraulic inherent frequency and the PID closed-loop system feature were calculated. The simulated result is consistent with those tested in the bench and on the site with 50 t heavy vehicle. The experimental result shows that the control method has quick response and high precision.     

Nitrosation and Nitration of Tetraacetyldibenzylhexaazaisowurtzitane

Tetraacetyldibenzylhitane (TADBIW) was subjected to debenzylation by nitrosating with inorganic materials available commercially to synthesize tetraacetyldinitrosohexaazaisowurtzitane (TADNSIW). TADNSIW was purified, and its structure was determined by FTIR, 1H NMR, MS and element analysis. The debenzylation reaction of TADBIW gave quantitative benzaldehyde as a by-product. This indicates that the reaction produces an imine cation as an intermediate. Hexanitrohexaazaisowurtzitane (HNIW) was prepared from unpurified TADNSIW with the yield over 96.0 % and the purity more than 98.0 %. And the mechanism of the reaction from TADNSIW to HNIW is proposed to be oxidation of nitroso and nitration of acetyl on the molecule of TADNSIW, This reaction system involved is simple, and the reaction can complete within a short time and under mild conditions. The product can be easily to separate and the waste disposed readily.     

Multiplication Model of EMCCD Based on Single Type of Carrier

The avalanche multiplication principle of electron multiplication CCD (EMCCD) was discussed on the basis of single type of carrier, and the multiplication model was built by using a classic piecewise ionization rate model and avalanche multiplication integral formula. Wolff’s ionization rate model was selected according to the structure and the multiplication gate amplitude of the actual devices. Compared the theoretical result with the multiplication curve of the actual device, it was found that only enough fringing field strength and multiplication area length could lead to adequate signal charge multiplication. The relationship between the multiplication gate amplitude and the total gain of the cascaded boosting EMCCD can be conveniently determined by using this model.     

Influence of A1203 particles on the microstructure and mechanical properties of copper surface composites fabricated by friction stir processing

The influence of three factors, such as volume percentage of reinforcement particles （i.e. A1203）, tool tilt angle and concave angle of shoulder, on the mechanical properties of Cu-A1203 surface composites fabricated via friction stir processing was studied. Taguchi method was used to optimize these factors for maximizing the mechanical properties of surface composites. The fabricated surface composites were examined by optical microscope for dispersion of reinforcement particles. It was found that A1203 particles are uniformly dispersed in the stir zone. The tensile properties of the surface composites increased with the increase in the volume percentage of the A1203 reinforcement particles. This is due to the addition of the reinforcement particles which increases the temperature of recrystallization by pinning the grain boundaries of the copper matrix and blocking the movement of the dislocations. The observed mechanical properties are correlated with microstructure and fracture features.     

Computational and Experimental Investigation on Aerodynamic Characteristics of Terminally Sensitive Projectile with S-C Shaped Fins

The design of terminally sensitive projectile scanning platform requires a better understanding of its aerodynamic characteristics.The terminally sensitive projectile with S-C fins has a complex aerodynamic shape,which is constructed with small length to diameter ratio cylindrical body on which two low aspect ratio fins are installed.The study focuses on the effect of fin aspect ratio on the aerodynamic characteristics.Simulation was carried on based on computational fluid dynamics(CFD) method,and the pressure distribution characteristic,drag coefficient,lift coefficient and rolling moment coefficient varying with attack angle were obtained.A free flying experimental investigation focused on the kinetic aerodynamics was made.The results show that the fins provide sufficient drag to balance the terminally sensitive projectile weight to keep it flying at low and stable speed.The lift coefficient has a negative linear varying with attack angle.The rolling moment decrease with the increase in attack angle and the decrease in wing span area.     

Design of ANSYS-based Cathode with Complex Groove

The profile of cathode with complex groove needs to be modified time after time during design of electrochemical machining (ECM) cathode.A design scheme using finite element method (FEM) for cathode with complex profile is put forward to shorten the period of cathode design.Based on Laplace equation,the potential distribution on parameter-transformation model was calculated by using ANSYS,which is compared to the potential distribution calculated by substituting conductivity and current efficiency into Laplace equation.According to the difference between the results calculated and simulated by ANSYS,the cathode profile was modified by adjusting the cathode boundary.The experiments show that the dimensions and shape of workpiece machined by numerically simulated cathode conform well with the blueprint.     

Experimental investigation of Tie6Ale4V titanium alloy and 304L stainless steel friction welded with copper interlayer

The basic principle of friction welding is intermetallic bonding at the stage of super plasticity attained with self-generating heat due to friction and finishing at upset pressure. Now the dissimilar metal joints are especially popular in defense, aerospace, automobile, bio-medical,refinery and nuclear engineerings. In friction welding, some special alloys with dual phase are not joined successfully due to poor bonding strength. The alloy surfaces after bonding also have metallurgical changes in the line of interfacing. The reported research work in this area is scanty. Although the sound weld zone of direct bonding between Tie6Ale4 V and SS304 L was obtained though many trials, the joint was not successful. In this paper, the friction welding characteristics between Tie6Ale4 V and SS304 L into which pure oxygen free copper(OFC) was introduced as interlayer were investigated. Boxe Behnken design was used to minimize the number of experiments to be performed. The weld joint was analyzed for its mechanical strength. The highest tensile strength between Tie6Ale4 V and SS304 L between which pure copper was used as insert metal was acquired. Micro-structural analysis and elemental analysis were carried out by EDS, and the formation of intermetallic compound at the interface was identified by XRD analysis.     

Mg-Al／PTEE烟火药爆炸性能的研究（英）

The object of the research are explosive properties of the pyrotechnic composite consist of fine grade magnesium-aluminium powder(PAM)and highly dispersed polytetrafluorethylene(PTFE).The composite reveals high resistance to all mechanical and thermal impulses and is extremely sensitive to hot sparks and open fire.The burning rate of the composition changes from 1 cm·s-1 to 100 m·s-1 along with decreasing its density.Charges of the composition with density below 1 g·cm-3 burn so violently,that the phenomena is similar to explosion.Charges with density above 1.1 g·cm-3 burn relatively rapidly and stably.The main part of the paper concerns the pressure impulses in the air generated during high-rate burning of the composition of bulk density.The nature of the generated pressure impulse is not that of a typical shock wave.A rise of pressure over the distance from the point of explosion to the maximum value lasts 50-100 milliseconds,while for shock waves this factor is less than a microsecond for equivalent charges.The methods of initiation of the composition influence the shape and parameters of the pressure impulse.The explanation of the nature of great changes of the composition burning rate has been proposed.The effect described in the paper was used for evaluation of explosive pressure resistance of industrial doors and windows.     

Experimental investigation of a cook-off temperature in a hot barrel

The experimental investigations of the effect of contact time/temperature on initiating the cook-off using 7.62 mm calibre cartridge cases （CC） were conducted previously. These cartridges were filled with commercial off-the-shelf （COTS） double based （DB） propellant （Bulls Eye） and were loaded in a hot chamber. The thermal explosion temperature is of great significance to both weapon designers and safety inspectors as it provides the operational limit and safe operating temperature. For CC under test, it was found that the cook-off temperatures of this propellant were encountered with the heat transfer profile of the simulated gun barrel between 151.4 ℃ and 153.4 ℃, with a reaction occurring in less than 300 s after the round was chambered. Usefully, each experiment was found to be consistent and repeatable.     

Effects of Squeeze-film Air Damping on Properties of MEMS Inertial Switch in Fuse

The squeeze-film air damping exists in a lot of micro-electronic-mechanical system (MEMS) devices unavoidably. The effects of air damping in traditional inertial switch with spring-mass system can be ignored for its large volume and mass. But, many properties of MEMS switch, such as sensitivity, resolution and contact time, are affected by the air damping caused from the squeezed air film between two parallel plates moving relatively. Based on the conservation laws for mass and flux and the nonlinear Reynolds equation, the coefficient of squeeze-film damping was derived. The dynamic responses of the inertial switch with and without squeeze-film damping were simulated by using software ANSYS. The simulated results show that the sensitivity and contact time of the switch descend by about 5% and 15%, respectively, when the effects of squeeze-film damping are considered.     

Research on Matching Relationship Between Number of Initiation Points and Charge Diameter

For shaped charges,LS-DYNA software was adopted to explore the influence of number of initiation points on the penetrator formation numerically.Changed the number of initiation points from 4 to 36,the performance of penetrator under four different kinds of typical charge diameter was analyzed,and the effect of detonation wave pressure on the liner was discussed.The minimum number of initiation points to substitute for annular initiation was obtained for each of four warheads with different charge diameters,and the curve representing the relation between the number of initiation points and charge diameter was found out also by using polynomial fitting.The simulation result provides a reference for the design of multimode warhead.     

Residual Characteristic of High-Velocity Steel Fragments Penetrating UHMWPE FRP Laminates

The mechanical performance of ultra-high molecular weight polyethylene fiber (UHMWPE) and its composites were proposed. Penetrated properties of different thicknesses UHMWPE FRP laminates (URP) impacted by 3.3g cubic high velocity fragments were studied. According to the ballistic experimental results and theoretical analysis, the linear relation between ballistic limit vBL and area density AD was confirmed. The relative parameters of showing experientially residual velocity vr were expressed by the function of AD. In the end, versatile experiential expression between vr and AD was found. Prediction of vr and vBL using obtained expressions under the above stated condition of impacting URP was consistent with the experimentaled results. Consequently, the two experiential relations can be used to predict the residual velocity and ballistic limit of cubic high velocity fragments impacting URP. The residual characteristic of high-velocity steel fragments penetrating UHMWPE FRP laminates can be more exactly forecasted by the two derived experiential formulas.     

Research on Effect of Adding Nanomaterial to Propellant on Gun Barrel

The barrel lifes of three small caliber rifles were tested by using the propellant with nanomaterial and the standard propellant respectively. The test results show that the service life increases observably due to adding nanomaterial to the propellant. Then, the influence of the nanomaterial on the tube was researched by splitting the two barrels tested and detecting their inner surfaces. It was found that the erosion of the barrel bore is reduced observably by using the propellant with nanomaterial. And it makes the volume and the size of the gun chamber change less. Therefore, the barrel life can be prolonged by adding the nanomaterial in the propellant.     

Research on Prediction Model for Erosion and Abrasion of Barrel Based on LSSVM

To predict the erosion and abrasion of high bore pressure tank gun barrel, the least square support vector machine (LSSVM) algorithm was used. Based on the gun firing test data, the prediction model for barrel's erosion and abrasion was established. It was adopted to predict the wear increment of gun barrel. The results show that the prediction values given by the model coincide with the measured data better, and the model can predict the barrel's wear accurately and rapidly.     

Modeling and Simulation for Gliding Missile with Large Aspect Ratio

An improved STT (skid to turn) autopilot was developed to solve the problem of roll control saturation for the gliding missile with large aspect ratio. A lateral acceleration feedback was introduced in the roll channel of the autopilot to ensure that the roll angle could closely follow the lateral acceleration,so that the sideslip angle and the roll rudder deflection could be reduced,and the roll control saturation was avoided. A six-DOF ( degree of freedom) nonlinear simulation model was set up. The simulation results indicate that the model and the control scheme are effective.     

Damage visualization and deformation measurement in glass laminates during projectile penetration

Transparent armor consists of glass-polymer laminates in most cases. The formation and propagation of damage in the different glass layers has a strong influence on the ballistic resistance of such laminates. In order to clarify the course of events during projectile penetration, an experimental technique was developed, which allows visualizing the onset and propagation of damage in each single layer of the laminate. A telecentric objective lens was used together with a microsecond video camera that allows recording 100 frames at a maximum rate of I MHz in a backlit photography set-up. With this technique, the damage evolution could be visualized in glass laminates consisting of four glass layers with lateral dimensions 500 mm x 500 mm. Damage evolution was recorded during penetration of 7.62 mm AP projectiles with tungsten carbide core and a total mass of 11.1 g in the impact velocity range from 800 to 880 rn/s. In order to measure the deformation of single glass plates within the laminates, a piece of reflecting tape was attached to the corresponding glass plate, and photonic Doppler velocimetry （PDV） was applied. With the photonic Doppler velocimeter, an infrared laser is used to illuminate an object to be measured and the Doppler-shifted light is superimposed to a reference light beam at the detector. The simultaneous visualization and PDV measurement of the glass deformation allow determining the deformation at the time of the onset of fracture. The analysis of the experimental data was supported by numerical simulations, using the AUTODYN commercial hydro-code.     

CdS/Cu纳米光催化剂降解废水中的HMX和RDX试验研究（英）

The wastewater with HMX and RDX was treated by photodegradation process in the presence of cadmium sulfide doped with copper as photocatalyst under UV and Vis irradiations.The influence on the degration of Cu% as dopant in CdS/Cu nanoparticles,pH of solution,dosage of photocatalyst and concentration of explosives were studied.The XRD patterns and UV-Vis spectra were used to characterize the nanoparticle.Results show that the degradation efficiency for HMX and RDX wastewater reaches 85%-88% in the presence of Cd0.95Cu0.05S under 180 min UV irradiation.The dosage of 160.0 mg·L-1 of photocatalyst and the pH of 7 are the optimum.A gradual decrease in degradation at the first two cycles is seen.     

Research on Hybrid Power System with Dual Stator-winding and Its Decoupled Control Strategy

For the bi-power system adopted widely in future armored vehicles,a hybrid power generator with dual stator-winding was proposed.Its structure and working principle were analyzed first,and its main parameters were determined and verified according to the power requirements.The system’s mathematical model was established,and a decoupled control method was put forward on the basis of the instantaneous reactive power theory.For the voltage building-up,a voltage control strategy was designed on the basis of mixed reactive power compensation to implement stabilized 28V and 270V outputs simultaneously.The simulation results show that the stabilization accuracy and disturbance rejection ability of the system are improved much more than other ordinary generators.     

Research on Cutting Trajectory of Electroplated Diamond Wire Saw

The cutting process of electroplated diamond wire saw was researched on the basis of impulse and vibration machining theories. The different contact states in the cutting process were analyzed by using the finite element method. It shows that the cutting stress is uniformly distributed along the direction of the workpiece width in the steady state. A mathematical equation of sawing trajectory was established by using the superposition principle and the cutting experiment of wire saw to calculate the cutting trajectory. The comparison of the theoretical trajectory with the calculated one indicates that the error is less than 15%. The research results provide a theoretic basis for optimization of the saw’s cutting process parameters.