共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
3.
采煤机液压CAT系统的设计应用 总被引:1,自引:0,他引:1
通过综合运用了计算机技术、自动化仪表及传感器技术,CAT是目前液压传动技术中比较先进的测试方法,此方法应用于采煤机液压系统的测试,提高了采煤机的工作可靠性。 相似文献
4.
采用当今新技术对长城特钢上世纪80年代初进口的20MN锻造液压机机组中的主泵液压系统、卸载液压系统、辅助液压系统、操作机液压系统和电气控制系统进行了改造,实际应用结果表明:改造后的锻造液压机的技术性能、自动化程度、可靠性和可维护性都得到了较大的提高.降低了原系统的液压冲击和振动,实现了±1mm的锻造精度,锻造频次由原来的70min-1提高到90min-1以上,同时还保证了原有系统的其他性能指标. 相似文献
5.
在分析液压动力转向器试验台工作原理的基础上,设计测控系统硬件结构和软件结构,并提出抗干扰和提高可靠性的措施。采用该系统可以进行转向器多项性能测试,在测试中实现了完全自动化,而且人机接口良好,测试精度高。 相似文献
6.
PLC在液压CAT中的应用 总被引:2,自引:1,他引:1
PLC在液压CAT(计算机辅助测试)中的应用可大大简化CAT控制系统的结构,与计算机构成网络之后,可进一步提高液压CAT的自动化测试水平。PLC应用于液压系统的故障诊断,能实现对故障的准确定位,有效地提高了液压系统的故障诊断水平。 相似文献
7.
8.
液压马达加载测试装置的设计研究 总被引:2,自引:0,他引:2
本文设计了一套液压马达的加载测试装置,该装置能够按照实际工况对液压马达进行性能测试,由于系统采用了比例控制技术和信号自动采集系统,从而提高了系统的测试自动化程度和测试精度;同时有效解决了液压马达的低速加载稳定性问题。 相似文献
9.
一、液压技术在机床中的应用自从1882年第一台液压龙门刨床问世以来,在一百年当中液压传动已在机床中得到广泛应用,液压元件成为机床中不可缺少的重要基础元件,特别是在机床向自动化、高速化、省力化以及提高机床的加工精度和可靠性,便于操作和维修等方向发展的过程中,液压传动显示出一系列优点,例如: 相似文献
10.
11.
C.J. Sun H.R. Geng Y.S. Shen X.Y. Teng Z.X. Yang 《金属学报(英文版)》2007,20(3):181-186
The rheology feature of Sb, Bi melt and alloys was studied using coaxial cylinder high-temperature viscometer. The results showed that the curve of torsion-rotational speed for Sb melt presents a linear relation in all measured temperature ranges, whereas for the Bi melt, the curve presents obvious non-Newtonian feature within the low temperature range and at relative high shear stress. The rheology feature of Sb80Bi20 and Sb20Bi80 alloy melts was well correlated with that of Sb and Bi, respectively. It is considered that the rheology behavior of Sb melt plays a crucial role in Sb80Bi20 alloy and that of Bi melt plays a crucial role in Sb20Bi80 alloy. 相似文献
12.
Peng Liu Zhao-Kuang Chu Yong Yuan Dao-Hong Wang Chuan-Yong Cui Gui-Chen Hou Yi-Zhou Zhou Xiao-Feng Sun 《金属学报(英文版)》2019,32(4):517-525
The effect of heat treatment on the microstructures and mechanical properties of a newly developed austenitic heat resistant steel(named as T8 alloy) for ultra-supercritical applications have been studied. Results show that the main phases in the alloy after solution treatment are γ and primary MX. Subsequent aging treatment causes the precipitation of M_(23)C_6 carbides along the grain boundaries and a small number of nanoscale MX inside the grains. In addition, with increasing the aging temperature and time, the morphology of M_(23)C_6 carbides changes from semi-continuous chain to continuous network.Compared with a commercial HR3C alloy, T8 alloy has comparable tensile strength, but higher stress rupture strength. The dominant cracking mechanism of the alloy during tensile test at room temperature is transgranular, while at high temperature, intergranular cracking becomes the main cracking mode, which may be caused by the precipitation of continuous M_(23)C_6 carbides along the grain boundaries. Typical intergranular cracking is the dominant cracking mode of the alloy at all stress rupture tests. 相似文献
13.
《中国铸造》2014,(6):540-541
Organized by Suppliers China Co., Ltd and co-organized by the National Technical Committee 54 on Foundry of Standardization Administration of China, the 15th Global Foundry Sourcing Conference 2014 (hereinafter referred to as FSC 2014) was successfully held on Sep. 23rd in Grand Regency Hotel, Qingdao. More than 500 delegates from home and abroad attended this conference, including over 130 purchasers from 20 countries and 380 domestic and foreign suppliers. 相似文献
14.
15.
LASER CLADDED TiCN COATINGS ON THE SURFACE OF TITANIUM 总被引:3,自引:0,他引:3
Y.L. Yang D. Zhang and H.S. Kou College of Science Northeastern University Shenyang China C.S. Liu College of Material Metallurgy Northeastern University Shenyang China 《金属学报(英文版)》2007,20(3):210-216
Laser cladded coatings of TiCN were produced on the surface of titanium. To obtain the optimal techniques, several conditions were tested by varying the laser scanning rate. The choice of shielding gas was also studied. The cladded coatings were then evaluated from the surface mechanics point of view based on their microhardness. The microstructure of some interesting samples was investigated by optical micrographs (OM). The results showed that under the condition of fixed pulse frequency and pulse width, the laser scanning rate and the shielding gas are the main factors influencing the components of coatings. TiCN coatings were decompounded and oxidized during the cladding process in the condition of no shielding gas of N2. X-ray diffraction results indicated that the composite coatings composed of TiCN, TiC, Ti2N, and TiO2 were produced using appropriate techniques. The results indicated that the best condition in terms of the surface microhardness is obtained when the scanning rate is 1.5mm / s, the pulse frequency is 15Hz, the pulse width is 3.0ms, and N2 is chosen as the shielding gas. The microhardness of the composite coatings is about 1331kg · mm - 2, which is about 4 times that of the substrate. The optical micrographs indicated that the cladding zone is made up of TiCN, TiO2, and some interdendritic Ti, but the diffusion zone mainly consists of the dendrites phase, and the cladded depth is about 80m, which is more than 2 times that of the laser nitrided sample. There were no microcracks or air bubbles in the cladded sample, which was cladded using the above optimal techniques. 相似文献
16.
X80 pipeline steel plates were friction stir welded(FSW) under air, water, liquid CO_2 + water, and liquid CO_2 cooling conditions, producing defect-free welds. The microstructural evolution and mechanical properties of these FSW joints were studied. Coarse granular bainite was observed in the nugget zone(NZ) under air cooling, and lath bainite and lath martensite increased signifi cantly as the cooling medium temperature reduced. In particular, under the liquid CO_2 cooling condition, a dual phase structure of lath martensite and fi ne ferrite appeared in the NZ. Compared to the case under air cooling, a strong shear texture was identifi ed in the NZs under other rapid cooling conditions, because the partial deformation at elevated temperature was retained through higher cooling rates. Under liquid CO_2 cooling, the highest transverse tensile strength and elongation of the joint reached 92% and 82% of those of the basal metal(BM), respectively, due to the weak tempering softening. A maximum impact energy of up to 93% of that of the BM was obtained in the NZ under liquid CO_2 cooling, which was attributed to the operation of the dual phase of lath martensite and fi ne ferrite. 相似文献
17.
《中国铸造》2014,(3):215-217
China Securities News reported on March 21, 2014: Guangdong Hongtu Wuhan Die Casting Co., Ltd. (Wuhan Hongtu), a wholly owned subsidiary of Guangdong Hongtu Technology (Holdings) Co., Ltd., held a groundbreaking ceremony recently. With the registered capital of 50 million Yuan, Wuhan Hongtu has a total land area of 100,000 square meters and a plant construction area of 72,000 square meters. It is expected to have a production capacity of about 30,000 tonnes of aluminum castings annually after it is put into production. 相似文献
18.
Z.C. Guo X.Y. Zhu R.D. Xu 《金属学报(英文版)》2007,20(2):111-116
The effects of pulse frequency f and duty cycle r on the deposition rate, composition, morphology, and hardness of pulse electrodeposited RE (rare earth)-Ni-W-P-SiC composite coatings have been studied. The results indicate that pulse current can improve the deposition rate of RE-Ni-W-P-SiC composite coatings; W, P, and SiC contents in the coating decrease with the increase of pulse frequency and reach the lowest value at f = 33Hz, whereas the RE content in the composite coatings increases with the increase of pulse frequency. SiC content decreases with the increase of duty cycle, W content reaches the lowest value, and P content reaches the highest value at r = 0.4; pulse current and RE can lead to smaller size of the crystalline grains; however, the effects of different pulse frequency and duty cycle on the morphologies of RE-Ni-W-P-SiC composite coatings are not obvious. The hardness of RE-Ni-W-P-SiC composite coatings is the highest when the duty cycle is at 0.6 and 0.8 and pulse frequency is at 50Hz. At the same pulse frequency, the hardness of RE-Ni-W-P-SiC composite coatings at r= 0.8 is higher than that at r= 0.6. 相似文献
19.
M.E Li G. C. Yang 《金属学报(英文版)》2007,20(4):258-264
Two new classes of growth morphologies, called doublons and seaweed, were simulated using a phase-field method. The evolution of doublon and seaweed morphologies was obtained in directional solidification. The influence of orientation and velocity on the growth morphology was investigated. It was indicated that doublons preferred growing with its crystallographic axis aligned with the heat flow direction. Seaweed, on the other hand, could be obtained by tilting the crystalline axis to 45°. Stable doublons could only exist in a range of velocity regime. Beyond this regime the patterns formed would be unstable. The simulation results agreed with the reported experimental results qualitatively. 相似文献
20.
Y.G. Cao S.F. Xue K. Tanaka 《金属学报(英文版)》2007,20(1):40-48
To investigate the causes that led to the formation of cracks in materials, a novel method that only considered the fracture surfaces for determining the fracture toughness parameters of J-integral for plain strain was proposed The principle of the fracture-surface topography analysis (FRASTA) was used. In FRASTA, the fracture surfaces were scanned by laser microscope and the elevation data was recorded for analysis. The relationship between J-integral and fracture surface average profile for plain strain was deduced. It was also verified that the J-integral determined by the novel method and by the compliance method matches each other well. 相似文献