Pure low-frequency flexural mode of [011](c) poled relaxor-PbTiO(3) single crystals excited by k(32) mode

Rhombohedral phase relaxor-PbTiO(3) solid solution single crystals poled along [011](c) exhibits superior lateral extensional piezoelectric response, which enables the excitation of a pure low frequency flexural mode with a bridge-type electrode configuration. For the ternary 0.24Pb(In(1/2)Nb(1/2)) O(3)-0.46Pb(Mg(1/3)Nb(2/3))O(3)-0.30PbTiO(3) single crystal poled along [011](c), the electromechanical coupling factor of the flexural mode reached as high as 0.66, and the resonance frequency of this mode can be easily made in kHz range, making it possible to fabricate very small size low frequency sensors and actuators. We have delineated theoretically the coupling between flexural mode and other modes and realized a strong pure flexure mode.     

Elastic, piezoelectric, and dielectric properties of 0.955Pb(Zn(1/3)Nb(2/3))O(3)-0.45PbTiO(3 ) single crystal with designed multidomains

The elastic, piezoelectric, and dielectric properties of a 0.955Pb(Zn(1/3)Nb(2/3))O(3)-0.045PbTiO(3 ) (PZN-4.5%PT) multi-domain single crystal, poled along [001] of the original cubic direction, have been determined experimentally using combined resonance and ultrasonic methods. At room temperature, the PZN-4.5%PT single crystal has rhombohedral symmetry. After being poled along [001], four degenerate states still remain. Statistically, such a domain-engineered crystal may be treated as having an average tetragonal symmetry, and its material constants were determined based on 4 mm symmetry. It was confirmed that the electromechanical coupling coefficient k(33) for the domain-engineered samples is >90%, and the piezoelectric constant d(33) is >2000 pC/N. A soft shear mode with a velocity of 700 m/s was found in the [110] direction. From the measured experimental data, the orientational dependence of phase velocities and electromechanical coupling coefficients was calculated. The results showed that the transverse and longitudinal coupling coefficients, k(31) and k(33), reach their maximum along [110] and [001], respectively.     

Complete set of material properties of single domain 0.24Pb(In(1∕2)Nb(1∕2))O(3)-0.49Pb(Mg(1∕3)Nb(2∕3))O(3)-0.27PbTiO(3) single crystal and the orientation effects

Multidomain relaxor-based single crystals have intrigued the enthusiasm of many researchers due to their superior electromechanical properties. In order to understand the physical origin of multidomain properties, one must know the complete set of material coefficients in single domain state. Previous published single domain data were all measured under bias because single domain state is unstable. Here, we report a set of single domain data without bias for rhombohedral 0.24Pb(In(1∕2)Nb(1∕2))O(3)-0.49Pb(Mg(1∕3)Nb(2∕3))O(3)-0.27PbTiO(3) single crystal. Comparing rotated coefficients from single domain data with measured multidomain material coefficients, we concluded that the orientation effects account for more than 90% of the observed multidomain properties.     

Characterization of flux-grown PZN-PT single crystals for high-performance piezo devices

Relaxor ferroelectric Pb(Zn(1/3)Nb(2/3))O(3-x)PbTiO(3) (PZN-PT) and Pb(Mg(1/3)Nb(2/3))O(3)-PbTiO(3)(PMN-PT) single crystals are the potential candidates for future high-performance piezoelectric devices due to their exceptionally high dielectric and piezoelectric properties. Characterization on flux-grown PZN-PT single crystals of different orientations revealed that PZN-(6-7)%PT single crystals show good homogeneity in dielectric and electromechanical properties and composition. When poled in [001] direction, these crystals exhibit high longitudinal-mode properties with dielectric constant (K(T)) approximately equal to 7000, piezoelectric coefficients (d(33)) approximately equal to 2800 pC/N, and electromechanical coupling factors (k(33)) > or = 0.92. For [011]-cut crystals, optimally poled PZN-7%PT single crystal exhibits very high transverse-mode dielectric and piezoelectric properties with K(T) > or = 5000, d(32) approximately equal to -3800 pC/N and k(32) > or = 0.90. [011]- poled PZN 6%PT has d(32) approximately equal to -3000 pC/N and comparable k(32) and K(T) values. In comparison with melt-grown PMNPT single crystals, flux-grown PZN-PT single crystals show good compositional homogeneity, superior and consistent dielectric and electromechanical properties, and higher depolarization temperatures (TDP).     

Electromechanical properties of fine-grain, 0.7 Pb(Mg(1/3)Nb(2/3))O3-0.3PbTiO3 ceramics

A fine grain, relaxor-based piezoelectric ceramic 0.7 Pb(Mg(1/3)Nb(2/3))O3-0.3PbTiO3 (PMN-30% PT) has been investigated, which was fabricated using the columbite precursor method. The complete set of electromechanical properties of the piezoceramic at room temperature is determined using a combination of ultrasonic and resonance techniques. This fine-grain ceramic (grain size < or = 2.5 microm) exhibits ultra-high dielectric permittivity (epsilon33(T)/epsilon0 approximately 7000) and a high coupling coefficient k(33) (= 0.78). Ultrasonic spectroscopy was used to measure the dispersion of the phase velocity and attenuation for the longitudinal wave propagating in the poling direction. Lower attenuation and smaller velocity dispersion were observed compared to modified Pb(Zr(x)Ti(1-x)O3 (PZT-5H) ceramics. The measurement results show that this fine-grain PMN-30% PT ceramic is a very good material for making ultrasonic array transducers.     

Electromechanical properties and anisotropy of single- and multi-domain 0.72Pb(Mg(1∕3)Nb(2∕3))O(3)-0.28PbTiO(3) single crystals

Complete sets of elastic, piezoelectric, and dielectric constants of 0.72Pb(Mg(1∕3)Nb(2∕3))O(3)-0.28PbTiO(3) single crystal poled along [111](c) (single domain) as well as non-polar axes [001](c) and [011](c) (multidomain) have been measured under natural conditions. These data allowed us to evaluate accurately the extrinsic contributions to the superior piezoelectric properties. Very large extrinsic contributions to the unusual anisotropies in multidomain crystals are confirmed. We found that the instability of domain structures is the origin of the low mechanical quality factor Q for the multidomain relaxor-based ferroelectric single crystals. Our results can provide useful guidance in future design of domain engineered materials.     

Full tensorial elastic, piezoelectric, and dielectric properties characterization of [011]-poled PZN-9%PT single crystal

Transverse piezoelectric property of 0.91Pb(Zn(1/3)Nb(2/3))O(3)-0.09PbTiO(3) (PZN-9%PT) single crystal poled along [011] direction under different fields have been investigated, the poling field giving the best property was between 350 and 650 V/mm at room temperature. Full tensorial elastic, dielectric, and piezoelectric properties of PZN-9%PT single crystal poled along the [011] direction under 500 V/mm have been determined by resonance and ultrasonic methods. It was found that the electromechanical coupling coefficients k(32) and k(33) can reach 0.90 and 0.89 and the piezoelectric coefficients d(32) and d(15) are -1705 and 2012 pC/N, respectively. This complete set of physical properties can provide convenience for piezoelectric device fabrication and domain engineering studies.     

Forty-channel phased array ultrasonic probe using 0.91Pb(Zn(1/3 )Nb(2/3))O(3)-0.09PbTiO(3) single crystal

A 0.91Pb(Zn(1/3)Nb(2/3))O(3)-0.09PbTiO (3) (PZN-PT) single crystal with high electromechanical coupling factor (k(33))>90% has been used to fabricate a 40-channel phased array ultrasonic probe with greater sensitivity and broader bandwidth than conventional probes. This probe has a center frequency of 3.5 MHz and an aperture of about 6.0x7.5 mm. The standard probe fabrication process was modified for PZN-PT. The dispersion of echo signals was within +/-20% of the mean value. After recovery poling, the echo amplitude of the PZN-PT single-crystal probe is 8 and 5 dB higher than that of one- and two-matching-layer PZT probes, respectively. Moreover, the fractional bandwidth of the single-matching-layer PZN-PT probe is broader than that of the two-matching-layer PZT probes. The PZN-PT single crystals provide great improvements in the sensitivity and bandwidth of phased array probes.     

铌镁酸铋-钛酸铅压电陶瓷准同型相界附近的性能和相变温度研究

利用传统固相烧结法制备了Bi(Mg_2/3Nb_1/3)O₃-PbTiO₃(BMN-PT)压电陶瓷, 分析了不同PbTiO₃含量对BMN-PT压电陶瓷的晶体结构、介电、压电及铁电性能的影响. XRD结果表明: 合成的BMN-PT陶瓷具有纯钙钛矿结构, 并且在PbTiO₃含量为x=0.60时, 其组分的XRD图谱在衍射角2θ=45°出现明显的分峰, 说明该组分相结构中存在三方和四方相的共存. 压电铁电性能显示, BMN-0.60PT有最大的压电常数d₃₃(~170pC/N)和平面机电耦合系数k_p(0.35), 最小的矫顽场E_c(29.4 kV/cm)及最大的剩余极化P_r(31.4 μC/cm²). 确定了BMN-PT压电陶瓷的准同型相界(MPB)为PbTiO₃含量x=0.60的组分. 介电系数温谱表明介电系数峰值温度(Tm)随着PbTiO₃含量的增大而升高, MPB组分的Tm约为276℃.     

分凝对Pb(Mg1/3Nb2/3)O3-38%PbTiO3单晶的成分及介电、压电性能的影响

研究了用改进的Bridgman法生长的PMNT62／38单晶在其生长过程中的分凝现象，研究了分凝导致的成分不均匀及其对介电和压电性能的影响。XRFA分析表明，PMNT62／38单晶底部的PbTiO3(PT)含量为x=35.2mol%，而顶部的PT含量为43mol%。底部晶体（001），（110）和（111）三种切型的晶片加电场极化后，其介电和压电性能出现了异常的现象。（110）切型的压电模量最大，为1200pC/N；（111）次之，为789pC/N；（001）最低，为371pC/N。极化后的（110）和（111）晶片在室温、1kHz频率下的相对介电常数（两种切型的εr都在10000左右），约为（001）晶片（εr-5000)的1倍，并且介电常数在低温端有上升的趋势。     

A 20 MHz single-element ultrasonic probe using 0.91Pb(Zn(1/3 )Nb(2/3))O(3)-0.09PbTiO(3) single crystal

A 20 MHz single-element ultrasonic probe using 0.91Pb(Zn(1/3 )Nb(2/3))O(3)-0.09PbTiO(3) (PZN-PT 91/9) single crystal has been fabricated. The single crystal of PZN-PT 91/9 orientated to the (001) plane has longitudinal coupling factor of k(33)>90%, which is much larger than the k(33)=70 to 80% of conventional Pb(Zr(1-x),Ti(x))O(3) (PZT) based ceramics. A single crystal of PZN-PT 91/9 without inclusion or crack has been grown with dimensions of about 25x15x5 mm by the self-flux method. Because mechanical strength in the fabrication of disk transducers orientated to the (001) plane was sufficiently strong, under the same conditions as are applied to conventional PZT ceramics, a piston single-element probe with a diameter of 2.0 mm and a frequency of 20 MHz was successfully fabricated. The bandwidth of the PZN-PT 91/9 probe was 13-26 MHz, which was 4 MHz broader than that of the conventional PZT probe.     

Anisotropy in domain engineered 0.92Pb(Zn1/3 Nb2/3)O3-0.08PbTiO3 single crystal and analysis of its property fluctuations

The orientation dependence of slowness and electromechanical coupling coefficients of 0.92Pb(Zn/sub 1/3/Nb/sub 2/3/)O/sub 3/-0.08PbTiO/sub 3/ (PZN-8%PT) domain engineered single crystal was analyzed based on the measured complete set of elastic, piezoelectric, and dielectric constants. There exist one quasi-longitudinal, one quasi-shear, and one pure shear wave in each of the [100]-[010], [010]-[001], and [001]-[110] planes. The slowness of the quasi-shear wave exhibits strong anisotropy in all three planes, and the coupling coefficient k/sub 33/ and k/sub 31/ reach their maximum in [001] and [110] directions of cubic axis, respectively. Because the composition of the PMN-8%PT system is very close to the morphotropic phase boundary, the extraordinary large piezoelectric coefficients d/sub 31/ and d/sub 33/, and high coupling coefficient k/sub 33/ are very sensitive to compositional variation. We have performed error analysis and proposed an improved characterization scheme to derive a complete data set with best consistency.     

Determination of nonlinear electromechanical energy conversion and the field-dependent elastic modulus of Pb(Mg(1/3)Nb(2/3 ))O(3)-based electrostrictors

Energy conversion efficiency is a critical parameter for all electromechanical materials. Although excellent techniques are available for linear materials, nonlinearities complicate the determination of conversion efficiency in electrostrictive Pb(Mg(1/3)Nb(2/3 ))O(3) (PMN). The field dependence of the elastic modulus presents additional problems. A technique combining pulse-echo ultrasound has been developed to approximate the change in the Young's modulus with applied field. A 30% decrease was observed at 1 MV/m (from ~100 to ~70 GPa). The boundary condition for these measurements was a constant electric field as opposed to constant dielectric displacement. In combination with the results from harmonic analysis, the modulus data may be used to determine the electromechanical conversion efficiency. This has been accomplished using an energy balance criterion for a PMN-based composition (with and without dc bias). The resulting longitudinal coupling values are >0.5 for practical electric fields (<1 MV/m peak).     

Electric-field and stress effects on depoling and overpoling phenomena in [001]-poled transverse mode Pb(Zn1/3Nb2/3)O3-(6-7)%PbTiO3 single crystal of [110] length cut

Solid-solution Pb(Zn(1/3)Nb(2/3))O(3)-PbTiO(3) (PZN-PT) single crystals, touted as next-generation piezoelectric materials, have been studied extensively in the past decade. This work addresses the advantages and limitations of transducers made of transverse mode PZN-(6-7)%PT single crystals of [110](L) X [001](T)(P) cut. This cut exhibits superior electromechanical properties, with k(31) ≈ 0.85 and d(31) ≈-1450 pC/N, and an extremely high d(31)/S(E)(11) value of >35 C/m(2). It also has relatively high overpoling, i.e., rhombohedralto- tetragonal phase transformation, field of ≈2 kV/mm. This overpoling field further decreases with increase in axial compressive stress. Despite these good attributes, this crystal cut has a low depoling field of ≤ 0.3 kV/mm, a result of low coercive fields of [001]-poled relaxor-based single crystals, which decreases further with increasing axial compressive stress, limiting its bipolar drive capability. The axial compressive stress required to cause overpoling via rhombohedral-to-tetragonal phase transformation of relevant domain variants in the crystal is found to be >90 MPa. In contrast, this crystal cut depolarizes at comparatively low axial tensile stress of ≈15 MPa, the magnitude of which is not significantly affected by the moderate forward field applied.     

67 Pb(Mg1/3Nb2/3)O3-33PbTiO3单晶90铁电畴光学研究

采用偏光显微镜观察了67Pb(Mg1/3Nb2/3)O3-33PbTiO3固溶体铁电单晶在室温时90铁电畴结构.铁电畴结构与晶体质量有关,在正交偏光显微镜下光学透明晶体中存在着尺寸为23mm的均匀大畴,不同极化方向的大畴重叠形成雾状区,使晶体表现出光学质量宏观不均匀.在光学质量差的雾状晶体中则存在着0.1mm宽的110型带状孪生畴,使晶体形成表面浮凸,带状畴内还存在着90°亚畴.并对这些畴的形成作了讨论     

Highly polarized single-c-domain single-crystal Pb(Mn,Nb)O(3)-PZT thin films

In-plane unstrained single-c-domain/single-crystal thin films of PZT-based ternary ferroelectric perovskite, ξPb(Mn,Nb)O3-(1 - ξ)PZT, were grown on SrRuO(3)/Pt/MgO substrates using magnetron sputtering followed by quenching. The sputtered unstrained thin films exhibit unique ferroelectric properties: high coercive field, Ec > 180 kV/cm, large remanent polarization, P(r) = 100 μC/cm(2), small relative dielectric constants, ε* = 100 to 150, high Curie temperature, Tc = ~600 °C, and bulk-like large transverse piezoelectric constants, e31,f = -12.0 C/m(2) for PZT(48/52) at ξ = 0.06. The unstrained thin films are an ideal structure to extract the bulk ferroelectric properties. Their micro-structures and ferroelectric properties are discussed in relation to the potential applications for piezoelectric MEMS.     

1-3型水泥基压电复合材料的制备及性能

采用切割-浇注法, 以硫铝酸盐水泥为基体, 制备了1-3型水泥基压电复合材料。详细阐述了1-3型水泥基压电复合材料的制备过程; 研究了0.375Pb(Mg_1/3Nb_2/3)O₃-0.375PbTiO₃-0.25PbZrO₃压电陶瓷柱的宽厚比w/t对1-3型水泥基压电复合材料的压电性能、 介电性能和声阻抗的影响。结果表明: 压电陶瓷柱的宽厚比w/t对1-3型水泥基压电复合材料性能有很大影响, 随着w/t的增加, 其压电应变常数d₃₃、 机电耦合系数K_p与K_t、 机械品质因数Q_m、 介电常数ε_r和介电损耗tanδ均随着w/t的增加而减小, 而压电电压常数g₃₃值几乎不受w/t的影响。在压电陶瓷体积分数仅为22.72%的条件下, 调节压电陶瓷柱的宽厚比w/t至0.130, 可使复合材料的声阻抗与混凝土的声阻抗十分接近, 从而有效地解决了智能材料在土木工程中的声阻抗相容性问题。      

三元陶瓷Pb(In1/2Nb1/2)O3-Pb(Ni1/3Nb2/3)O3-PbTiO3准同型相界附近组分的介电、铁电和压电性能

铅基复合钙钛矿铁电材料广泛应用于机电传感器、致动器和换能器。二元铁电固溶体Pb(Ni_1/3Nb_2/3)O₃- PbTiO₃(PNN-PT)由于其在准同型相界(MPB)区域具有优异的压电、介电性能而备受关注。然而较大的介电损耗和较低的居里温度限制了其在高温高功率器件方面的应用。本研究通过引入Pb(In_1/2Nb_1/2)O₃ (PIN)作为第三组元改善PNN-PT的电学性能, 提高其居里温度; 通过两步法合成了MPB区域的三元铁电陶瓷Pb(In_1/2Nb_1/2)O₃- Pb(Ni_1/3Nb_2/3)O₃-PbTiO₃ (PIN-PNN-PT), 研究了其结构、介电、铁电和压电性能。制备的所有组分陶瓷具有纯的钙钛矿结构。随着PT含量的增加, 陶瓷结构从三方相转变为四方相。通过XRD分析得到了室温下PIN-PNN-PT体系的MPB相图。体系的居里温度由于PIN的加入得到了很大的提高, 更重要的是PIN的引入降低了PNN-PT体系的介电损耗和电导。MPB处的组分展现出了优异的电学性能, 室温下, 性能最优组分为0.30PIN-0.33PNN-0.37PT: d₃₃=417 pC/N, T_C=200 ℃, ε′= 3206, tanδ=0.033, P_r=33.5 μC/cm², E_C=14.1 kV/cm。引入PNN-PT的PIN第三组元使得体系的居里温度和压电性得到提高的同时降低了的介电损耗和电导率, 因此, PIN-PNN-PT三元铁电陶瓷在高温高功率换能器等方面具备一定的应用潜力。     

Preparation of Pb(Mg1/3Nb2/3)O3–Pb(Zn1/3Nb2/3)O3 ceramics by the B-site precursor method and dielectric characteristics

Powders in the Pb(Mg1/3Nb2/3)O3–Pb(Zn1/3Nb2/3)O3 system, with a high perovskite yield, were prepared by a B-site precursor method. PbO was added to pre-reacted B-site components of Mg1-xZnxNb2O6 solid solution, which was further calcined to form a perovskite structure. Perovskite phase contents and lattice parameters were obtained from X-ray analyses. Weak-field low-frequency dielectric constants and losses of sintered pellets were measured as functions of composition, temperature and frequency. Dielectric relaxation behaviours were investigated in terms of diffuseness coefficients. Microstructures were observed to correlate with other characteristics. © 1998 Chapman & Hall     

A 3.7 MHz phased array probe using 0.91Pb(Zn(1/3)Nb(2/3))O(3)-0.09PbTiO(3 )

A novel 128-channel phased array probe for echocardiography with a center frequency of 3.7 MHz using 0.91Pb(Zn(1/3)Nb(2/3))O(3)-0.09PbTiO(3 ) (PZN-9%PT) single crystal has been fabricated to realize greater sensitivity and broader bandwidth properties. The echo amplitude of the PZN-9%PT single-crystal probe is about 5 dB higher than that of the conventional lead airconate titanate (PZT) ceramic probe, and the fractional bandwidth is about 25 percentage points broader. The quality of B mode images obtained by the PZN-9%PT probe satisfies the performance of the two types of conventional PZT ceramic probes that have center frequencies of 2.5 and 3.75 MHz. At the reference frequency of 3 MHz, the Doppler sensitivity of the PZN-9%PT probe is about 5 dB higher than that of the 3.75 MHz PZT probe; the blood flow of a pulmonary vein in a hard-to-image patient is much more clearly imaged than in the case of using the PZT probe. These superior images are attributable to the use of sufficiently large PZN-9%PT single crystals obtained by the self-flux method.