煅烧温度对溶胶-微波法制备Pr掺杂纳米TiO_2及其光学性能的影响

以钛酸丁酯和硝酸镨为原料,采用溶胶-微波法合成纳米Pr-TiO_2。采用X射线衍射、扫描电镜、X射线能谱和紫外-可见光等手段研究了煅烧温度对其晶体结构、表观形貌及光学性能的影响。结果表明:镨的掺杂对纳米TiO_2的形貌及光催化性能有显著影响。镨的掺杂抑制了晶粒的生长,抑制了晶型由锐钛矿相向金红石相的转变。随着煅烧温度的增加,纳米TiO_2团聚加剧,比表面积降低,锐钛矿相逐渐向金红石相转变,并且光催化过程中产生的活性羟基量逐渐减少,光催化活性逐渐降低,其中当煅烧温度为500℃时所合成的纳米Pr-TiO_2的光催化效果最优。Pr掺杂TiO_2提高了可见光的利用率并且红移了50nm。     

二氧化钛纳米粒子对胺类化合物的光催化降解

研究了晶粒粒径相近的金红石相、锐钛矿相和混晶纳米二氧化钛对苯胺、甲萘胺和邻氯苯胺3种物质的光催化降解。结果表明,晶粒粒径相近的金红石相和锐钛矿相二氧化钛纳米粒子对胺类化合物的光催化效果相近,特别是在反应的开始阶段,两者的差异很小;随着反应时间的增加,金红石相纳米二氧化钛的催化能力稍优于锐钛矿相纳米二氧化钛。成分不同的混晶的催化能力相差较大,随着混晶中的金红石相含量增加,催化剂的催化效果有了显著的提高。实验中还发现,不同的催化剂对苯胺、甲萘胺和邻氯苯胺3种物质同时催化过程中,3种有机物降解程度的顺序均为甲萘胺>邻氯苯胺>苯胺。     

二氧化钛纳米粒子的低温合成及可见光催化性能

介绍一种低温合成二氧化钛纳米粒子的新方法.将非晶型二氧化钛加入强酸性溶液中室温搅拌数小时后得到无色透明的溶液.继续在室温搅拌数48h后,可以得到高比表面的金红石相二氧化钛纳米粒子.改变处理过程温度及酸的种类,可以得到不同组成的纤维状二氧化钛纳米粒子.对盐酸体系进行详细讨论结果表明,在低于60℃时得到的是热力学稳定的金红石单一相,而在高于120℃时得到的是热力学亚稳态的锐钛矿单一相,高于170℃时得到的是锐钛矿及金红石的混合相,显示出与众不同的结晶行为.通过此低温法制备的金红石相二氧化钛在具有较小的吸收禁带的同时,还拥有100n2·g-1以上的比表面积.与锐钛矿相相比,显示了良好的可见光催化活性.     

四氯化钛水解法制备二氧化钛纳米晶的影响因素

研究了四氯化钛水解法制备的二氧化钛纳米晶工艺中水解８温度和硫酸根离子对粉体性能的影响室温下的水解产物为无定形结构,这种粉体有着很大的比表面积,其孔为介孔尺度;添加少量的硫酸根离子使粉体的孔径在２～５ｎｍ,最可几孔径为３．８ｎｍ,提高水解温度能得到金红石与锐钛矿相的混晶,同样的水解温度下,添加少量的硫酸根离子则为纯锐钛矿相,用到金红石与锐钛矿相的混晶,同样的水解温度下,添加少量的硫酸根离子则为纯锐钛     

纳米金红石型TiO2的低温制备

分别在中性，碱性和酸性环境下对钛酸四丁酯溶液进行水解以制备纳米二氧化钛。在中性和碱性环境下水解产物是非晶态的，当温度低于700℃煅烧只能得到脱钛矿型二氧化钛。在酸性环境下，通过调整酸和水的加入量将溶液在低温下（40－50℃）水解合成了从纯锐钛矿相到不同比例锐钛矿－金红石混晶相，再到纯金红石相的纳米二氧化钛，乙醇的加入促进凝胶的形成以及锐钛相向金红石相的转化。     

硫酸亚钛爆轰制备纳米TiO2粒子

以硫酸亚钛,氨水,硝酸铵和黑索金炸药为主要原料,结合沉淀法和爆轰技术对爆轰合成纳米二氧化钛进行了研究,同时利用X射线粉晶衍射仪(XRD)和高分辨透射电子显微镜(HRTEM)等对爆轰灰及经过在空气中500℃,1h处理后的爆轰灰进行测试分析,结果表明:收集的爆轰灰是以金红石和锐钛矿相的二氧化钛为主粒径为(30±10)nm的球形超微粉,同时含有少量的杂质(Ti7O13和C),经过500℃,1h的热处理除杂后,制备的二氧化钛纳米粉末仍为金红石和锐钛矿相组成的混晶,金红石相和锐钛矿相的相对含量比为9∶1,二氧化钛晶粒有轻微长大现象.     

TiO2纳米微粒的溶胶—凝胶法制备及XRD分析

本文采用溶胶-凝胶法制备二氧化钛纳米微粒。用XRD分析了二氧化钛胶体经不同温度热处理后的晶粒粒径。分析表明温度在437K时TiO2微粒呈锐钛矿结构，粒径约为5.5nm。在673K以上TiO2粒径迅速增大，微粒出现锐钛相与金红石相混昌结构。973K时TiO2微粒完全转化为金红石相。用晶界结构弛豫的观点解释粒径随热处理温度变化关系。     

偏钛酸爆轰合成纳米TiO2研究

首先对纳米二氧化钛的应用及目前现有的合成纳米二氧化钛技术方法及特点做了简单的介绍。其次主要地介绍了以偏钛酸为原料，混合炸药爆轰合成纳米二氧化钛粉末的研究。并用XRD、TEM、DTA／TG和比表面仪等手段对产物进行了表征，分析结果表明所得的二氧化钛粉末为纳米级，晶型为金红石型和锐钛矿型的混晶，颗粒呈球形和片状，锐钛矿型和金红石型平均晶粒度大小分别为6．8和24nm，纳米粉末的比表面积为116．8m^2／g。     

TiO2纳米微粒的溶胶-凝胶法制备及XRD分析

本文采用溶胶 凝胶法制备二氧化钛纳米微粒。用XRD分析了二氧化钛胶体经不同温度热处理后的晶粒粒径。分析表明温度在 4 73K时TiO2 微粒呈锐钛矿结构 ,粒径约为 5 5nm。在 6 73K以上TiO2 粒径迅速增大 ,微粒出现锐钛相与金红石相混晶结构。 973K时TiO2 微粒完全转化为金红石相。用晶界结构弛豫的观点解释粒径随热处理温度变化关系     

纳米二氧化钛粉体晶相控制实验研究

在水解－沉淀法制备纳米TiO2粉体的过程中，使用不同的沉淀剂获得了晶相不同的纳米TiO2粉体，使用混合沉淀剂，通过控制沉淀剂的比例，制备了晶相组成（金红石与锐钛矿比例）不同的纳米TiO2多晶粉体，采用相同的粉体制备工艺，不同的后续处理工艺，探讨了锐钛矿向金红石转变的相变温度，经分析研究后认为，水解－沉淀法制备的纳米粉体中的锐钛矿向金红石红转变的温度为500－800℃，完全转变的温度在800℃以上；纳米TiO2多晶粉体的晶相组成不仅与沉淀剂的种类，混合沉淀剂中沉淀剂的比例和粉体的煅烧温度有关，而且与粉体的后续处理工艺和粉体表面界面相的稳定性有关。     

Sol-Gel法制备纳米TiO2过程中水解pH值的影响及其性能表征

采用钛酸四异丙酯[Ti(i-OC3H7)4]水解法制备纳米TiO2粉体，水解过程中有很多参数对纳米TiO2的特征产生影响，通过控制制备过程中的水解pH值，可以得到不同粒径和不同晶型的纳米TiO2粉体，本文主要探讨了纳米TiO2晶型转变的条件和晶粒度Dhkl随pH值变化的趋势，并利用XRD，TEM对粉体颗粒的形貌，大小，物相组成进行分析，XRD分析研究表明，纳米的A→R相变和水解pH值密切相关。     

二氧化钛纳米晶的光催化活性研究

以苯酚的光催化降解为模型反应,研究了锐钛矿相和金红石相二氧化钛纳米晶（７￣４０ｎｍ）的光催化活性。与市售的氧化钛相比,两种晶相的纳米氧化钛均有很高的光催化活性,锐钛矿相氧化钛对苯酚的深度矿化有更高的选择性。ＴｉＯ２吸附的水及羟基会降低氧化钛的光催化活性。由于粒径减小使氧化钛的吸收带边界蓝移,粒径小的氧化钛有更高的催化活性,粒径〈１５ｎｍ时,显示出量子尺寸效应。     

Phase-pure TiO(2) nanoparticles: anatase, brookite and rutile

We report on the synthesis of phase-pure TiO(2) nanoparticles in anatase, rutile and brookite structures, using amorphous titania as a common starting material. Phase formation was achieved by hydrothermal treatment at elevated temperatures with the appropriate reactants. Anatase nanoparticles were obtained using acetic acid, while phase-pure rutile and brookite nanoparticles were obtained with hydrochloric acid at a different concentration. The nanomaterials were characterized using x-ray diffraction, UV-visible reflectance spectroscopy, dynamic light scattering, and transmission electron microscopy. We propose that anatase formation is dominated by surface energy effects, and that rutile and brookite formation follows a dissolution-precipitation mechanism, where chains of sixfold-coordinated titanium complexes arrange into different crystal structures depending on the reactant chemistry. The particle growth kinetics under hydrothermal conditions are determined by coarsening and aggregation-recrystallization processes, allowing control over the average nanoparticle size.     

纳米TiO2粉晶的XRD研究

用溶胶－凝胶法制备了纳米ＴｉＯ２粉晶,对不同温度自理的系列粉末用Ｘ射线衍射进行了研究,发现所得粉晶随热处理温度的不同发生了从锐钛矿到金红石相的转变。对系列粉晶进行了Ｘ射线衍射点阵参量计算,结合所得的晶粒度和微结构参数,发现纳米ＴｉＯ２粉晶组元中存在着晶格畸变。     

二氧化钛催化剂晶型调控技术的研究进展

综述二氧化钛由锐钛矿向金红石晶型转变调控技术的最新成果,分析温度、氧化物和以及离子掺杂对实现晶型转变的影响规律,重点研究氧化物和离子掺杂对晶型转变的影响。结果显示:复合金属氧化物熔点低于TiO2熔点时,可促进锐钛矿型TiO2向金红石型转变;而金属氧化物熔点高于TiO2熔点时,可阻碍晶型转变;掺杂离子的离子半径、化合价、离子大小对二氧化钛晶型转变及催化性能有明显的影响,当掺杂金属离子半径大于或小于Ti4+半径,使得锐钛矿型TiO2更稳定;当掺杂离子的半径与Ti4+半径相近时,有利于锐钛矿型向金红石型转变,而体积较小的低价阴离子有利于金红石型二氧化钛的的生成,体积较大的高价阴离子则有利于锐钛矿型二氧化钛的的生成;阴阳离子共掺杂可以有效地调控二氧化钛晶型转变,并且能够提高TiO2的光催化活性。探讨二氧化钛多晶之间的协同作用,并基于二氧化钛掺杂改性的计算模拟,指出今后的发展方向。     

Controlled fabrication of TiO2 rutile nanorod/anatase nanoparticle composite photoanodes for dye-sensitized solar cell application

We present a straightforward procedure to prepare composite photoanodes which consisted of TiO2 rutile nanorods/anatase nanoparticles synthesized under hydrothermal conditions, with the ratio of rutile to anatase controlled simply by adjusting the volume of nitric acid. The as-prepared TiO2 composites exhibited high specific surface area, light-scattering effect, and good crystallinity. The dye-sensitized solar cells (DSCs) using the TiO2 composites showed higher short-circuit photocurrent and overall conversion efficiency than the DSC from pure-anatase nanoparticles. The highest conversion efficiency was achieved from the DSC based on TiO2 nanocomposites with 24 wt% rutile nanorods, which was attributed to improved light harvesting caused by the enhancement of specific surface area and scattering effect from rutile nanorods.     

Photocatalytic degradation of dyes and organic contaminants in water using nanocrystalline anatase and rutile TiO2

Nanocrystalline TiO₂ was synthesized by controlled hydrolysis of titanium tetraisopropoxide. The anatase phase was converted to rutile phase by thermal treatment at 1023 K for 11 h. The catalysts were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), Fourier-transform infrared absorption spectrophotometry (FT-IR) and N₂ adsorption (BET) at 77 K. This study compare the photocatalytic activity of the anatase and rutile phases of nanocrystalline TiO₂ for the degradation of acetophenone, nitrobenzene, methylene blue and malachite green present in aqueous solutions. The initial rate of degradation was calculated to compare the photocatalytic activity of anatase and rutile nanocrystalline TiO₂ for the degradation of different substances under ultraviolet light irradiation. The higher photocatalytic activity was obtained in anatase phase TiO₂ for the degradation of all substances as compared with rutile phase. It is concluded that the higher photocatalytic activity in anatase TiO₂ is due to parameters like band-gap, number of hydroxyl groups, surface area and porosity of the catalyst.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Photocatalytic degradation of dyes and organic contaminants in water using nanocrystalline anatase and rutile TiO2

Nanocrystalline TiO₂ was synthesized by controlled hydrolysis of titanium tetraisopropoxide. The anatase phase was converted to rutile phase by thermal treatment at 1023 K for 11 h. The catalysts were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), Fourier-transform infrared absorption spectrophotometry (FT-IR) and N₂ adsorption (BET) at 77 K. This study compare the photocatalytic activity of the anatase and rutile phases of nanocrystalline TiO₂ for the degradation of acetophenone, nitrobenzene, methylene blue and malachite green present in aqueous solutions. The initial rate of degradation was calculated to compare the photocatalytic activity of anatase and rutile nanocrystalline TiO₂ for the degradation of different substances under ultraviolet light irradiation. The higher photocatalytic activity was obtained in anatase phase TiO₂ for the degradation of all substances as compared with rutile phase. It is concluded that the higher photocatalytic activity in anatase TiO₂ is due to parameters like band-gap, number of hydroxyl groups, surface area and porosity of the catalyst.     

Synthesis of nano titania particles embedded in mesoporous SBA-15: characterization and photocatalytic activity

Supported nanocrystalline titanium dioxide (TiO2) has been prepared by a post-synthesis step via Ti-alkoxide hydrolysis through the use of mesoporous SBA-15 silica. TiO2/SBA-15 composites with various TiO2 loading have been prepared and characterized by X-ray diffraction, nitrogen adsorption, Fourier transform infrared spectroscopy and diffusive reflective UV-vis spectroscopy. The addition of mesoporous SBA-15 prevents the anatase to rutile phase transformation and the growth of crystal grain. TiO2 did not block the SBA-15 pores, and their surface was fully accessible for nitrogen adsorption. Calcination in air of the composites up to 800 degrees C did not change the nanocrystal phase and slightly increased the domain size from 5.0 to 7.5 nm, indicating that the anatase TiO2 grains in the mesostructures have a relatively high thermal stability and proper pore diameter allows controlling the size of obtained titania particles. The TiO2/SBA-15 composites prepared by this study showed much higher photodegradation ability for methylene blue (MB) than commercial pure TiO2 nanoparticles P-25. Experimental results indicate that the photocatalytic activity of titania/silica mixed materials depends on the adsorption ability of composite and the photocatalytic activity of the titania, and there is an optimal ratio of Ti:Si, too high or low Ti:Si ratio will lower the photodegradation ability of the composites.