共查询到20条相似文献,搜索用时 62 毫秒
1.
准确的驾驶室惯性参数,包括质量、质心位置、转动惯量和惯性积等,是整车动力学分析的基本参数。本文以某国产重卡整备驾驶室为研究对象,利用LMS数据采集系统测量频率响应函数,采用称重法获得重卡驾驶室的平面质心位置。从频率响应函数中提取质量线计算质心位置,与称重法结果进行对比,X方向误差为1.99cm,Y方向误差为0.68cm。该结果表明质量线法具有较高的测量精度。计算整备驾驶室的转动惯量、惯性积、主惯性矩和惯性主轴方向,并对引起试验误差的原因进行分析。 相似文献
2.
介绍了一种基于三线扭摆法测试动力总成质心和惯性参数的测量方法和实验台的开发。该方法和实验台的特点是:(1)采用悬吊法悬吊被测试物体,因而容易保证被测物体的质心落在三线摆的扭摆轴线上;(2)计算质心与惯性参数的方法基于坐标变换,坐标变换中的数据由测量的坐标点计算得到。坐标点由三坐标测量仪测量得到,测试精度高。对一个长方形组合件的质心和惯性参数进行了测试,并和理论值进行了对比,表明了实验台具有测试简单、高效和文中的数据处理方法有效、精度高的特点。给出了一个动力总成质心与惯性参数的测试结果,分析表明基于该测试方法和数据处理方法建立的实验台和数据处理系统,具有较好的测试重复性和测试精度。 相似文献
3.
4.
大型刚体惯性参数识别的三线扭摆系统实验方法改进研究 总被引:2,自引:0,他引:2
精确获取汽车动力总成刚体惯性参数是发动机悬置系统设计的重要前提之一。利用三线扭摆法测量刚体单轴转动惯量精度较高的特点,基于表面固定点确定刚体方位的三点定位方法和测量6个~9个不同方位的多次测量原理,发展了一套适合于大型复杂刚体的惯性参数识别方法。关键技术有:(1)选取刚体表面三个定位点定义一个刚体随动坐标系以描述刚体方位;(2)通过测量刚体定位点至托盘表面参考点(定义一个整体坐标系)的距离,计算出定位点在整体坐标系下的坐标和两个坐标系之间的转换关系;(3)求出各组实验中在动坐标系下的刚体转轴方位和转动惯量;(4)运用最小二乘原理,求解多个转轴的最优交点得到动坐标系下的刚体质心坐标,求解由转动惯量转轴定理导出的线性方程组得到刚体惯性矩阵。实验方法中容易引起误差的环节较多,但是可以根据最小二乘原理进行逐级误差估计和控制。通过误差分析、长方体质量块实验验证和大量的汽车动力总成惯量参数识别实验,证明了该方法的实用性和可靠性。 相似文献
5.
汽车动力总成的惯性参数(转动惯量和惯性积)通常采用实验方法进行测量,测量误差一般不超过3 %。动力总成悬置系统的固有特性与动力总成惯性参数、悬置刚度、位置、角度密切相关,从而悬置系统的固有频率和解耦率的理论设计值与其真实值之间必然存在一定程度偏差。采用均匀分布随机变量描述惯性参数,以悬置刚度为优化设计变量,提出稳健优化模型对某轿车悬置系统固有特性进行稳健优化。优化结果表明,与确定性优化方法相比,稳健优化方法可以较大幅度地提高频率、解耦率、频率间隔的稳健性。 相似文献
6.
7.
精准高效的坐标获取方式在模态分析的参数识别和性能优化等方面具有重要意义。基于模态试验中刚体振动的原理,分析其线参量和角参量的转换关系,推导出获取激励和响应坐标的方程,并结合质量线法得到惯性参数表达式。通过研究坐标获取误差的影响因素,搭建发动机动力学模型的仿真试验平台,进一步验证坐标获取与惯性参数识别的方法。以某型号变速箱总成为试验对象,利用基于最小二乘的卷积拟合算法(Savitzky-Golay, SG)对数据平滑滤波处理,对比电子三维坐标仪法、三维模型法与所提方法在坐标获取中的精度,然后选用质量线法识别惯性参数,并将其与MPC转动惯量测试平台计算的结果进行讨论。结果表明:相较传统方法,所提方法直接从模态试验中获取坐标,效率极大提升,成本显著降低,操作更加简便;同时几何坐标获取和质心坐标识别的最大误差在3 mm左右,转动惯量相对误差最大不超过7%,其精度优于部分测量方法,具有一定的工程应用价值。 相似文献
8.
9.
10.
11.
A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling. 相似文献
12.
V. T. Bublik A. I. Voronin E. A. Vygovskaya V. F. Ponomarev N. Yu. Tabachkova O. V. Toropova 《Inorganic Materials》2011,47(14):1563-1568
An analysis of anisotropy of the properties of a Bi2Se0.3Te2.7 solid solution was carried out using construction of demonstrative surfaces for thermoelectric effectiveness and thermal
expansion coefficients. It is shown that the texture is an important factor forming anisotropy of properties and technological
fitness of ingots for manufacturing modules. Anisotropy of properties based on the studies of the ingot textures obtained
using the float-zone method and Bridgman method (growing thermoelectric plates in a flat cavity) was studied. 相似文献
13.
O'Brien RS 《Radiation protection dosimetry》2003,105(1-4):95-100
Australia has several uranium mines and a large number of mineral sand mines, with associated processing facilities. Exposures resulting from these mining and processing operations usually involve intakes of mixtures of radionuclides. This work describes the development of a suite of first order, linear compartment models, based on the ICRP Publication 66 respiratory tract model, and an analytical solution to the decay equations, for assessing the consequences of such intakes. The computer programs based on these models directly compute excretion, organ retention and organ and whole-body doses for intakes of either single radionuclides or any mixture of radionuclides belonging to the same radioactive decay chain. The intake can be via inhalation, ingestion or injection, and can be acute, chronic or of limited duration. The starting concentration and degree of secular (dis)equilibrium can be specified for each radionuclide. No assumptions need to be made about the relative magnitudes of the radioactive half-lives of the different nuclides. 相似文献
14.
15.
16.
17.
Development is continued of the empirical method for the calculation of the heat of combustion of organic compounds and, in particular, of hydrocarbons of different structures by the additive scheme based on their chemical structure. 相似文献
18.
An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a
rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate
agreement is demonstrated between the derived relations and experimental data. 相似文献
19.
本文根据多年的实践检定经验 ,参照JJF1 0 59- 1 999《测量不确定度评定与表示》以及《测量不确定度表达 1 0讲》 ,对卧式金属罐容量的测量结果不确定度进行了评定。 相似文献
20.