共查询到20条相似文献,搜索用时 156 毫秒
1.
2.
要实现平面工作台的精密定位,需要对其运动进行检测,并设计相应的控制方案.为同步检测平面工作台三自由度位移,研制了图像处理位移检测系统.以CCD相机为核心结合显微镜放大、图像采集和图像处理构成检测系统.系统的位移检测不受工作台大幅转动的影响.检测系统既有较高的位移分辨率,又有一定的位移检测范围.使用图像处理位移检测系统,对清华大学制造的平面精密工作台的运动性能进行了测试.工作台干涉运动均小于主运动,通过合理的开环控制对各个运动方向上的干涉运动进行补偿,获得了工作台在平面任意方向上的运动.工作台小范围定位能力的检测表明工作台具有很高的定位分辨率. 相似文献
3.
4.
5.
6.
本文提出一种新的高精度大型平面扫描仪。利用双光束补偿系统,扫描头由一特殊光路组成。当入射光发生角漂或扫描头发生摆动等,输出的两束光发生对称上下漂移,其中心线扫描形成的基准平面保持不变。测量不确定度小于2.5×10-6。 相似文献
7.
8.
9.
10.
《真空科学与技术学报》2020,(7)
设计了一套回旋振荡器高阶体模开放式谐振腔自动扫描测试装置。该装置通过计算机程序控制,采用BJ1400标准矩形波导作为天线检测辐射场,扫描精度可达0.05 mm,具有100 dB的动态范围。以140 GHz的TE_(28,8)高阶体模谐振腔场分布检测为例,当扫描步长在水平方向和垂直方向分别取0.5 mm和0.3 mm时,y方向电场波峰和波谷的检测数据相差约10 dB。 相似文献
11.
目的研究汽车翼子板前门区域尺寸匹配控制方法,提高前门区域尺寸匹配平整度。方法从拉延补充工艺面造型、直翻工艺、侧翻角度3个方面来优化成形工艺,依据回弹扫描结果进行局部回弹补偿,建立翼子板的前门区域尺寸匹配控制方法。结果大量同类翼子板应用测试结果表明,在拉延补充工艺面造型、直翻工艺、侧翻角度3个方面的工艺优化基础上,进行局部区域的回弹补偿,可以使翼子板的前门区域匹配精度较好地达到评估标准。结论实验验证这套方案适合多数翼子板零件,可以有效保证翼子板与前门匹配处平整度。 相似文献
12.
Antenna characterisation and radar cross section measurements can be conveniently and successfully carried out by means of a compact antenna test range (CATR), whose performance is primarily assessed in terms of quiet zone size and field uniformity. CATR characterisation and diagnostics are usually performed by means of (amplitude and phase) field measurements in the quiet zone and are of timely interest either on CATR installation or on its periodic reassessments performed by manufacturers and/or users. This paper addresses CATR characterisation from amplitude-only data, an attractive topic because of the application of CATRs to the millimetre or sub-millimetre wave ranges. The approach is based on an appropriate strategy retrieving the missing quiet zone phase and facing the issue of the large electrical dimensions of the CATR. To take into account the characteristics of the collimating system as well as to keep as low as possible the number of unknowns to be sought for, it exploits the Jacobi-Bessel expansion of the aperture field. The performance of the algorithm has been tested through a wide numerical analysis against synthetic data generated by GRASP8-SE whose full version is routinely employed for CATR design. The main results related to a Gregorian dual offset reflector CATR, modelled on that proposed in the literature by Pistorius et ah, and to a single offset reflector CATR, inspired by the one available at the Queen Mary & Westfield College, London (UK), are reported. 相似文献
13.
平面度是几何量测量中的一个重要参数。测量得到的平面是利用理想平面作为基准,使其它计量器具有相应的参照平面,从而对其平面度进行评定。本文根据对角线评定方法,对平面度测量的数学模型及不确定度的评定进行了探讨。 相似文献
14.
本文首先通过形状记忆合金的材性试验研究了形状记忆合金的超弹性变形性能,并将其等效拟合为多线性模型,得到其设计参数,并详细介绍了分析计算时所采用的形状记忆合金的本构模型。然后,针对框架结构的变形特点,提出了一种基于形状记忆合金的消能减震装置,即在底层框架柱的反弯点附近设置锚固装置,形状记忆合金索的上端固定在锚固装置上,将其下端锚固在地下,在震时通过其来回反复变形耗散地震能量。然后通过有限元程序对设置形状记忆合金索的新型框架与普通框架进行静力推覆分析和低周反复分析,研究表明新型框架不仅屈服承载力和极限承载力高于普通框架,而且其滞回环更加饱满,累积塑性滞回耗能能力提高了41.4%,形状记忆合金索的滞回环也很饱满,具有优良的耗能能力,最后,还比较了对角设置形状记忆合金索的框架的耗能能力与本消能减震装置的耗能能力。因此该消能减震装置在减轻框架柱震害方面具有一定的工程应用价值和前景。 相似文献
15.
Winker DM 《Applied optics》1994,33(24):5712-5714
Large. inexpensive scanning mirrors for a lidar have been designed and built out of common float glass mirrors and aluminum honeycomb.The flatness of the scanning mirrors has been characterized with a modified Foucault knife-edge test.The peak-to-peak surface slope error over the entire surface of the mirrors was found to be less than 1 mrad, with slope errors of 0.15 mrad over small areas. This performance was sufficient for use of the mirrors in a scanning CO(2) lidar system that uses direct detection. 相似文献
16.
介绍了一种对电梯导轨的各项几何参数进行同步、快速、综合检测的高精度检测仪器。文中提出了利用反转法对系统的误差进行补偿的原理和方法,有效地提高了系统的检测精度。 相似文献
17.
分布式光纤拉曼放大器研制的进展 总被引:2,自引:0,他引:2
对分布式光纤拉曼放大器研究的历史、基本原理、优化设计以及现状和进展进行了讨论.对S波段的色散补偿型分布式光纤拉曼放大器以及采用光纤拉曼激光器作为抽运源,在前向抽运和后向抽运条件下,对5kmDCF-50kmG652光纤色散补偿型分布式光纤拉曼放大器增益光谱和噪声谱进行了研究.设计和制作了光纤光栅的增益平坦滤波器,取得了较好的增益平坦效果.FRA-1型分布式光纤拉曼放大器在校园网进行了应用试验,取得了较好的试验效果. 相似文献
18.
The flatness of individual components can critically influence the fit or lack-of-fit of compact, small assemblies. To ensure high yield, flatness is tightly toleranced and controlled. According to the standard definition of flatness, the underlying distribution of flatness measurements should be asymmetric. In this paper, 20 industrial flatness data sets from four different processes and three different materials are examined. To accommodate measurement round-off and small sample sizes, the Moran log spacing statistic is used to test if the normal distribution provides an adequate fit. The results demonstrate that the symmetric normal distribution provides an adequate fit for all the data sets. Such a result is important in confirming the use of root-mean-square tolerance analysis techniques, as well as selecting process monitoring and summarizing statistics. 相似文献
19.
在动态压力测量领域中,带引压管腔的压力测量系统常被用于空间狭小、工况恶劣等情况下的压力测量,压力信号经过引压管腔传递往往发生畸变,引压管腔是降低压力测量系统频响的首要因素。本文首先介绍了带引压管腔的压力测量系统物理结构模型,阐述管腔动态特性影响动态测量机理。其次,介绍了现有引压管腔主要校准方法和装置,开展新型校准装置和方法研究,研制了一种静态压力及温度可调的校准装置。最后,利用该校准装置对带引压管腔的压力测量系统进行实验,对带引压管腔的压力测量系统的动态计量与补偿技术发展具有借鉴作用。 相似文献