Microwave digestion polarography for determining seven trace elements in Salvia Miltiorrhiza Root and compound Salvia Miltiorrhiza Root injection simultaneously

The sensitive second derivative waves of Cu(Ⅱ),Pb(Ⅱ),Cd(Ⅱ),Ni(Ⅱ),Zn(Ⅱ),Fe(Ⅱ)and Mn(Ⅱ),forming in the substrate solution(pH=9.26)consisting of ammonia,ammonium chlorid,gelatin and ascorbic acid were researched.The peak potentials of the polarographic waves of the seven ions are at about 0.48,0.63,0.79,1.04,1.28,1.44 and 1.60 V respectively.Combining with microwave technique,a new method for the simultaneous determination of the seven trace elements in Chinese traditional medicine was developed.The method is easy to operate,rapid,simple and convenient.When the signal-to-noise rate equals 3,the detection limits of Cu,Pb,Cd,Ni,Zn,Fe and Mn are 4.2×10 3,5.3×10 3,2.1×10 3,5.8×10 4,3.0×10 3,7.7×10 4 and 1.1×10 3 μg/mL respectively.Well linear relationships exist between the concentrations and the peak currents when Cu,Pb,Cd,Ni,Zn,Fe and Mn concentrations are within 8.5×10 3 10,9.7×10 3 10,4.5×10 3 10,1.2×10 3 10,6.4×10 3 10,1.5×10 3 10 and 2.8×10 3 10 μg/mL,respectively.The method has been used to the simultaneous determination of the seven trace elements in Salvia Miltiorrhiza Root and compound Salvia Miltiorrhiza Root injection,the relative standard deviations(RSDs)of the Cu,Pb,Cd,Ni,Zn,Fe and Mn in the two medicines are 3.9% and 5.8%,4.0% and 4.1%,4.3% and 5.7%,4.9% and 5.3%,4.4% and 4.7%,3.5% and 4.0%,0.51% and 2.8%,respectively;the comparisons of the determination results with the values obtained by the standard method indicate that the presented method has very well veracity.     

塑封球栅阵列焊点在温度循环下可靠性数值模拟

根据实际封装器件建立了三维有限元分析模型,模拟了PBGA焊点在温度循环载荷下的蠕变应变,比较了95.5Sn-3.8Ag-0.7Cu和63Sn-37Pb两种焊料形成的焊点在温度循环下的蠕变情况,预测了焊点在温度循环下的疲劳寿命,评价了两种焊点在温度循环条件下的可靠性.结果表明,两种焊点相比较,63Sn-37Pb焊点在循环中的蠕变现象更为显著,95.5Sn-3.8Ag- 0.7Cu焊点的疲劳寿命更长,可靠性更高.     

Dynamic recrystallization behavior of 35CrMo structural steel

1　ＩＮＴＲＯＤＵＣＴＩＯＮＤｕｒｉｎｇｈｏｔｗｏｒｋｉｎｇ ,ｓｅｖｅｒａｌｍｅｔａｌｌｕｒｇｉｃａｌｐｈｅｎｏｍｅｎａｓｕｃｈａｓｗｏｒｋ ｈａｒｄｅｎｉｎｇ (ＷＨ ) ,ｄｙｎａｍｉｃｒｅｃｏｖｅｒｙ (ＤＲＶ) ,ａｎｄｄｙｎａｍｉｃｒｅ ｃｒｙｓｔａｌｌｉｚａｉｔｏｎ (ＤＲＸ )ｏｃｃｕｒｓｉｍｕｌｔａｎｅｏｕｓ ｌｙ[1 5 ] .Ｅｓｐｅｃｉａｌｌｙ ,ｔｈｅｏｃｃｕｒｒｅｎｃｅｏｆＤＲＸ ,ｃａｎｒｅｆｉｎｅｇｒａｉｎａｎｄｒｅｄｕｃｅｄｅｆｏｒｍａｔｉｏｎｒｅｓｉｓｔａｎｃｅｉｎｐｒａｃｔｉｃａｌｈｏｔ ｗ…     

Measurement and Analysis of Density of Molten Ni-W Alloys

1IntroductionNi-based heat-resistant superalloys are widely usedto make critical components in gas-turbine engines,suchas bladeetc.But they are very hard and difficult to bemachined,the net-shape machining of these materials isveryimportant.Computer simul…     

Flow stress behavior of Cu13Zn alloy deformed at elevated temperature

Ｃｏｎｓｔｉｔｕｔｉｖｅｍｏｄｅｌｉｓａｍａｔｈｅｍａｔｉｃａｌｒｅｐｒｅｓｅｎｔａｔｉｏｎｏｆｔｈｅｄｅｆｏｒｍａｔｉｏｎｒｅｓｐｏｎｓｅｏｆａｍａｔｅｒｉａｌｔｏｅｘｔｅｒｎａｌｌｙａｐ ｐｌｉｅｄｌｏａｄｉｎｇ ,ｉｎｃｌｕｄｉｎｇｅｎｖｉｒｏｎｍｅｎｔａｌｆａｃｔｏｒｓ .Ｔｈｅｐｒｅ ｃｉｓｅｋｎｏｗｌｅｄｇｅｏｆｔｈｅｃｏｎｓｔｉｔｕｔｉｖｅｂｅｈａｖｉｏｒｏｆｔｈｅｍａｔｅｒｉａｌｉｓｔｈｅｆｏｕｎｄａｔｉｏｎｏｆｎｕｍｅｒｉｃａｌｓｉｍｕｌａｔｉｏｎｔｅｃｈｎｏｌｏｇｙｏｆｍａｔｅｒｉ…     

Drag reduction of flow boiling with polymer additives

Ｓｏｍｅｓｔｕｄｉｅｓｗｅｒｅｄｏｎｅｏｎｐｏｏｌｂｏｉｌｉｎｇｈｅａｔｔｒａｎｓｆｅｒｏｆａｄｄｉｔｉｖｅａｑｕｅｏｕｓｓｏｌｕｔｉｏｎ ,ｂｕｔｌｉｔｔｌｅｏｎｆｌｏｗｂｏｉｌｉｎｇ[1 3] .Ｔｈｅｕｓｅｄａｄｄｉｔｉｖｅｓａｒｅｓｕｒｆａｃｔａｎｔａｄｄｉｔｉｖｅｓａｎｄｐｏｌｙｍｅｒａｄｄｉｔｉｖｅｓ[1 4] .Ｉｎｖｅｓｔｉｇａｔｉｏｎｓｏｎｔｈｅｄｒａｇｒｅｄｕｃｔｉｏｎｏｆａｄｄｉｔｉｖｅｓａｒｅｕｓｕａｌｌｙｃｏｎ ｃｅｎｔｒａｔｅｄｏｎｓｉｎｇｌｅｐｈａｓｅｆｌｏｗ[5 ] ,ｏｒｒａｔｈｅｒ,…     

Superplastic Deformation Behavior of Hot-rolled AZ31 Magnesium Alloy Sheet at Elevated Temperatures

1IntroductionAs a typical wrought magnesiumalloy,AZ31alloyhas a wide prospect for applications inthe fields of auto-mobiles,electronic appliances and aeronautic facili-ties[1,2].However,due to the hexagonal close-packed(HCP)structure of magnesium,the ductility of AZ31al-loy at roomtemperature is rather poor,which greatly re-stricts its applications in structural fields[3-5].Owing tothe activation of non-basal slip system[6],the ductility ofMg alloycan be significantlyimproved at elevatedtem…     

High temperature plastic deformation behavior of non-oriented electrical steel

High temperature plastic deformation behavior of non-orientated electrical steel was investigated by Gleeble 1500 thermo-mechanical simulator at strain rate of 0.01−10 s⁻¹ and high temperature of 500–1 200 °C. The stress level factor (a), stress exponent (n), structural factor (A) and activation energy (Q) of high temperature plastic deformation process of non-orientated electrical steel in different temperature ranges were calculated by the Arrhenius model. The results show that, with dynamic elevation of deformation temperature, phase transformation from α-Fe to γ-Fe takes place simultaneously during plastic deformation, dynamic recovery and dynamic recrystallization process, leading to an irregular change of the steady flow stress. For high temperature plastic deformation between 500 and 800°C, the calculated values of a, n, A, and Q are 0.039 0 MPa⁻¹, 7.93, 1.9×10¹⁸ s⁻¹, and 334.8 kJ/mol, respectively, and for high temperature plastic deformation between 1 050 and 1 200 °C, the calculated values of a, n, A, and Q are 0.125 8 MPa⁻¹, 5.29, 1.0×10²⁸ s⁻¹, and 769.9 kJ/mol, respectively. Foundation item: Project(2005038560) supported by the Postdoctoral Foundation of China; Project(05GK1002-2) supported by Key Program of Hunan Province     

Synthesis and characterization of arsenate antimonic acid AAAc(1 : 1)

The AAAc(1 : 1) was synthesized in water by As₂O₃ and Sb₂O₃ with molar ratio of 1 : 1. AAAc(1 : 1) was characterized by Raman, IR, TG/DTG, DSC, XPS and XRD. The results show that there are four peaks to v _s of As-OH, As-O-Sb, Sb-OH and Sb-O-Sb in Raman spectra of AAAc(1 : 1) at 100 – 1 000 cm⁻¹. The solution of AAAc(1 : 1) was also titrated with KOH solution. The titration results show that AAAc(1 : 1) is a hexabasic acid with dissociation constants of k ₁=3.62 × 10⁻², k ₂=3.05 × 10⁻³, k ₃=6.43 × 10⁻⁶, k ₄ =9.78 × 10⁻⁸, k ₅=1.32 × 10⁻¹¹, k ₆=3.87 × 10⁻¹². AAAc(1 : 1) has a good solubility and stability in water, its solid obtained by free volatilizing water from its solution under air at ambient temperature is amorphous. Chemical and thermal analysis show that the composition of AAAc(1 : 1) is As₂O₅ · Sb₂O₅ · 8H₂O in air at 25 °C. AAAc(1 : 1) has the structure of AsO(OH)₂-OH-Sb(OH)₄-O-Sb(OH)₄-OH-AsO(OH)₂ or As(OH)₃-O-Sb(OH)₄-O-Sb(OH)₄-O-As(OH)₃ (isomerism) through experimental determination and geometry optimization. Foundation item: Project(50274075) supported by the National Natural Science Foundation of China     

High Efficieney Synthesis of Isotaetie Polypropylene and Linear Polyethylene Using a New C2-symmetrie Carbon-bridged Zireonoeene Catalyst

Ansa-Cyclohexyl-bis（4,5,6,7-tertrahydro-l-indenyl） zirconium dichloride （5） was used as catalyst for propylene and ethylene polymerization together with methyl aluminoxane （MAO） as the cocatalyst. Isotactic polypropylene （PP） was obtained with the highest activity of 6.37× 107g PP （molZr）^-1h^-1. The mesomeso （mmmmm） pentads sequence content of PP was determined by 13C NMR spectroscopy. The dependence of the microstructure on the reaction temperature and the AI/Zr molar ratio was examined and the catalytic activity of complex 5 was compared with that of the similar ansa-zirconocene 3. The high activity of the new zirconocene 5 for propylene isospectic polymerization at high temperature （60℃） is the result of its unique bridged-group structure. Complex 5/MAO displays also high catalytic activity of 0.46× 10^6 to 9.87× 10^6g PE（molZr）^-h^-in the homo-polymerization of ethylene, The visometric molecular weight of PE ranges from 0.97×10^4 to 11.16×10^4 g.mol^- under the given conditions.^13C NMR spectroscopy analysis proves the PE to be linear polyethylene （LPE）.     

Enhancement of natural ventilation in rectangular enclosure with two openings by thin fin

A numerical method was used to study the natural ventilation in a rectangular enclosure with two symmetrical openings. In order to improve the natural ventilation efficiency, a fin was introduced into the enclosure. Steady-state heat transfer by laminar natural ventilation in a partially divided rectangular enclosure was investigated by numerically solving equations of mass, momentum and energy. Streamlines and isotherms were produced and heat transfer rate were calculated. A parametric study was carried out using the following parameters: Rayleigh number (1×10³ − 1×10⁶), dimensionless length (0–0.7) and position values (−0.7−0.7). It is found that the Nusselt number is an increasing function of Rayleigh number. By comparing with no-fin case, it is concluded that fin can effectively enhance the natural ventilation in the enclosure. Foundation item: Project(50408019) supported by the National Natural Science Foundation of China     

Effects of particle size on the mechanical properties of particle-reinforced Sn-Ag composite solder joint

Particulate size has significant influenced on the mechanical properties of particle-reinforced composite solder joints. In this current research, Cu or Ni reinforcement particles were mechanically added to the Sn-3.5Ag eutectic solder, and the effects of the particle size on the mechanical properties of particle-reinforced composite solder joint were systematically studied. This investigation touched on how mechanical properties of the solder joints are affected by particles size. A quantitative formula was set up to correlate the mechanical property of the solder joint with particle size in different processing conditions. Besides, the fracture mechanism of the composite solder joint was analyzed.     

Physical simulation of hot deformation of TiAI based alloy

In order to establish a model between the grain size and the process parameters, the hot deformation behaviors of Ti-49.5Al alloy was investigated by isothermal compressive tests at temperatures ranging from 800 to 1 100 ℃ with strain rates of 10^-3-10^-1 s^-1. Within this range, the deformation behavior obeys the power law relationship, which can be described using the kinetic rate equation. The stress exponent, n, has a value of about 5.0, and the apparent activation energy is about 320 J/mol, which fits well with the value estimated in previous investigations. The results show that, the dependence of flow stress on the recrystallized grain size can be expressed by the equation: σ = K1 drex^-0.56. The relationship between the deformed microstructure and the process control parameter can be expressed by the formula: lgdrex= -0.281 1gZ 3.908 1.     

Enhancement of flow boiling heat transfer with surfactant

The surfactant additive octadecylamine (ODA) was used to enhance the flow boiling heat transfer of water in vertical copper tube, and the effects of the aqueous solution properties, mass fraction of ODA, mass flux and heat flux etc. on flow boiling heat transfer were investigated. In order to analyze the mechanism of enhancement on boiling heat transfer with ODA, the copper surface was detected by XPS, and the diagram of binding energy was obtained. The results show that ODA can be adsorbed on the surface of the copper wall, and affects the properties of the heating surfaces and enhances the flow boiling heat transfer of water. Only in low heat flux and in a suitable range of concentration, can ODA aqueous solution enhance flow boiling heat transfer, and the suitable mass fraction of ODA is in the range of 1 × 10⁻⁵ −5 × 10⁻⁵. In addition, compared with water, ODA aqueous solution does not increase the flow drag under the same experimental conditions. Foundation item: The Natural Science Foundation of Tianjin(No. 94220) Biography of the first author: QIU Yun-ren, doctoral student, born in Dec. 1966, majoring in heat and mass transfer in chemical engineering.     

Electrochemical kinetics of gold dissolving in alkaline thiourea solution

1 INTRODUCTIONEssentially , determination of electrode reac-tion mechanism is just the determination of thecourse of electrode reaction and the rate-determi-ning step[1 5]. Based on the previous results[6 11],gold dissolution mechanism undergoes the follow-ing courses in alkaline thiourea solution: adsorp-tion of thiourea on active points of electrode sur-face and formation of Au[SC(NH2)2]ads; chargetransfer fromactive gold atomto thiourea moleculeand formation of Au[SC(NH2)2]a+ds; Au-…     

Spectra and DNA-binding properties of two novel mixed-ligand complexes containing organosulfonate

Two novel mixed-ligand complexes, [M(phen)₂(ans)₂]·H₂O (M = Cd(II) 1, Zn(II) 2; phen is 1, 10-phenanthroline, and ans is 4-aminonaphthalene-1-sulfonate), were obtained from the reaction of 1, 10-phenanthroline, sodium 4-aminonaphthalene-1-sulfonate tetrahydrate and acetate in mixed solvents. Interaction of the complexes with calf thymus DNA (ctDNA) were investigated using UV-vis absorption spectra, luminescence titrations, steady-state emission quenching by [Fe(CN)₆]⁴⁻, DNA competitive binding with ethidium bromide (EB) and viscosity measurements. The experimental results indicate that there exist two interaction modes between the complexes and DNA, namely the electrostatic interaction and intercalation, with the binding constants of 1.82 × 10⁵ M⁻¹ for 1 and 4.78 × 10⁴ M⁻¹ for 2 in buffer of 50 mM NaCl and 5 mM Tris-HCl (pH 7.0). Funded by Key Project of the National Natural Science Foundation of China (No. 60537050)     

Direct rapid determination of traces of sulfide in environment samples

An improved ethylene blue method for determination of sulfide is developed. It has been adapted to a direct determination of sulfide by both common spectrophotometric method and total differential spectrophotometric method. In common spectrophotometric method, the calibration curve is A=1.69ρ+0.006 and the correlation coefficient is 0.9994.The apparent molar absorptivity is 5.42×104 L*mol-1*cm-1 and calibration curve is liner when ρ is in the range of 0-0.9 mg*L-1. In total differential spectrophotometric method, the calibration curve is A=9.25ρ+0.004 and the correlation coefficient is 0.9996. The apparent molar absorptivity is 2.96×105 L*mol-1*cm-1and calibration curve is liner when ρ is in the range of 0-0.10 mg*L-1. The sensitivity of this method is increased significantly compared with the former ethylene blue method. The speed of reaction is also faster than the former one. The limit of detection is found to be 1.0 ng*mL-1 by both common spectrophotometric method and total differential spectrophotometric method. Ten replicate analyses of a sample solution containing 100 ng*mL-1sulfide give a relative standard deviation of 1.8%. The effects of various cations and anions on the determination of sulfide are studied and procedures for removal of interference is described. The method is used for the determination of sulfide in environment samples with satisfactory results.     

Superplasticity of Mg-5.8Zn-1Y-Zr alloy sheet fabricated by combination of extrusion and hot-rolling processes

Superplastic behaviors of quasicrystal phase containing Mg-5.8Zn-1Y-0.48Zr alloy sheets fabricated by combination of extrusion and hot-rolling processes have been investigated at temperature ranging from 623 to 753 K and at the strain rates ranging from 10-4 to 10-2 s-1 by uniaxial tensile tests. An excellent superplasticity with the maximum elongation to failure of 1020% was obtained at 753 K and the strain rate of 1.04×10-3 s-1 and its strain rate sensitivity, m, is as high as up to 0.75. The microstructure was stable during superplastic deformation due to the uniformly distributed fine quasicrystal particles. In addition, micro-cavities and their coalescences were observed in the superplastic deformation of the ZW61 magnesium alloy. Grain boundary sliding (GBS) was considered to be the main deformation mechanism during the superplastic deformation. Dislocation creep controlled by atom diffusion through grain boundaries or interior grains is suggested mainly to accommodate the GBS in super-plastic deformation.     

Dynamics of electrodeposition of tetraethylthioram disulphide (TETD) on pyrite surface

Ｄｉｅｔｈｙｌｄｉｔｈｉｏｃａｒｂａｍａｔｅ(ＤＤＴＣ)ｉｓｏｎｅｏｆｔｈｅｍｏｓｔｆｒｅｑｕｅｎｔｌｙｕｓｅｄｃｏｌｌｅｃｔｏｒｆｏｒｆｌｏｔａｔｉｏｎｏｆｈｅａｖｙ ｍｅｔａｌｓｕｌｆｉｄｅｍｉｎｅｒａｌｓ,ｓｕｃｈａｓｇａｌｅｎａ ,ｃｈａｌｃｏｐｙｒｉｔｅａｎｄｊａｍｅｓｏｎｉｔｅ ,ａｎｄｓｈｏｗｓｓｔｒｏｎｇｓｅ ｌｅｃｔｉｖｉｔｙ[1] .ＩｔｉｓｒｅｐｏｒｔｅｄｔｈａｔＤＤＴＣｉｓａｐｏｗｅｒｆｕｌｃｏｌｌｅｃｔｏｒｆｏｒｇａｌｅｎａａｎｄｖｅｒｙｓｅｌｅｃｔｉｖｅａｇａｉｎｓｔｐｙｒｉｔｅｉ…     

Strength and elastic properties of sandstone under different testing conditions

A laboratory experimental program performed on Wuhan sandstones was presented under monotonic loading, partial cyclic loading during loading path and sine wave cyclic loading with different strain rates to compare uniaxial compression strength and elastic properties （elastic modulus and Poisson ratio） under different conditions and influence of pore fluid on them. When the loading strain rates are 10^-5, 10^-4 and 10^-3/s, uniaxial compression strengths of dry sandstones are 82.3, 126.6 and 141.6 MPa, respectively, and that of water saturated sandstones are 70.5, 108.3 and 124.1 MPa, respectively. The above results show that the uniaxial compression strength increases with the increase of strain rate, however, variation of softening coefficient is insignificant. Under monotonic loading condition, tangent modulus increases with an increment of stress （strain） to a maximum value at a certain stress level, beyond which it starts to decline. Under the partial cyclic loading during loading path condition, unloading or reloading modulus is larger than loading modulus, and unloading and reloading moduli are almost constants with respect to stress level, especially unloading modulus. Under the sine wave cyclic loading condition, tangent modulus and Poisson ratio display asymmetric ‘X＇ shape with various strain, and the average unloading modulus is larger than the average loading modulus.