Design of 1 kbit antifuse one time programmable memory IP using dual program voltage

A 1 kbit antifuse one time programmable (OTP) memory IP, which is one of the non-volatile memory IPs, was designed and used for power management integrated circuits (ICs). A conventional antifuse OTP cell using a single positive program voltage (V _PP) has a problem when applying a higher voltage than the breakdown voltage of the thin gate oxides and at the same time, securing the reliability of medium voltage (V _M) devices that are thick gate transistors. A new antifuse OTP cell using a dual program voltage was proposed to prevent the possibility for failures in a qualification test or the yield drop. For the newly proposed cell, a stable sensing is secured from the post-program resistances of several ten thousand ohms or below due to the voltage higher than the hard breakdown voltage applied to the terminals of the antifuse. The layout size of the designed 1 kbit antifuse OTP memory IP with Dongbu HiTek’s 0.18 μm Bipolar-CMOS-DMOS (BCD) process is 567.9 μm×205.135 μm and the post-program resistance of an antifuse is predicted to be several ten thousand ohms.     

Design of an 8 bit differential paired eFuse OTP memory IP reducing sensing resistance

For the conventional single-ended eFuse cell, sensing failures can occur due to a variation of a post-program eFuse resistance during the data retention time and a relatively high program resistance of several kilo ohms. A differential paired eFuse cell is designed which is about half the size smaller in sensing resistance of a programmed eFuse link than the conventional single-ended eFuse cell. Also, a sensing circuit of sense amplifier is proposed, based on D flip-flop structure to implement a simple sensing circuit. Furthermore, a sensing margin test circuit is proposed with variable pull-up loads out of consideration for resistance variation of a programmed eFuse. When an 8 bit eFuse OTP IP is designed with 0.18 μm standard CMOS logic of TSMC, the layout dimensions are 229.04 μm × 100.15 μm. All the chips function successfully when 20 test chips are tested with a program voltage of 4.2 V.     

High precise control method for a new type of piezoelectric electro-hydraulic servo valve

A new type of piezoelectric electro-hydraulic servo valve system was proposed. And then multilayer piezoelectric actuator based on new piezoelectric ceramic material was used as the electricity-machine converter of the proposed piezoelectric electro-hydraulic servo valve. The proposed piezoelectric electro-hydraulic servo valve has ascendant performance compared with conventional ones. But the system is of high nonlinearity and uncertainty, it cannot achieve favorable control performance by conventional control method. To develop an efficient way to control piezoelectric electro-hydraulic servo valve system, a high-precise fuzzy control method with hysteresis nonlinear model in feedforward loop was proposed. The control method is separated into two parts: a feedforward loop with Preisach hysteresis nonlinear model and a feedback loop with high-precise fuzzy control. Experimental results show that the hysteresis loop and the maximum output hysteresis by the PID control method are 4.22% and 2.11 μm, respectively; the hysteresis loop and the maximum output hysteresis by the proposed control method respectively are 0.74% and 0.37 μm, respectively; the maximum tracking error by the PID control method for sine wave reference signal is about 5.02%, the maximum tracking error by the proposed control method for sine wave reference signal is about 0.85%.     

Effect of technological parameters on optical performance of fiber coupler

To find out the influence of technological parameters on optical performance of fused optical fiber device, the fiber coupler was served as subject investigated by using the fused biconical taper machining as experimental setup. Fused fiber coupler＇s optical performances such as insertion loss, excess loss, directivity and uniformity were tested with the optical test system that was constituted of tunable laser and optical spectrum analyzer. Especially the relationship between optical performance and drawing speed was investigated. The experimental results show that the optical performance is closely related to process conditions. At fused temperature of 1 200℃, there exists a drawing speed of 150μm/s, which makes the device＇s performance optimum. Out of this speed region, the optical performance drops quickly. At drawing speed of 200μm/s, the excess loss is relatively small when the fused temperature is above 1 200 ℃. So the technological parameters have close relationship with optical performance of the coupler, and the good performance coupler can＇t get until the drawing speed and fused temperature match accurately.     

Synthesis and structural characterization of macroporous bioactive glass

Porous sol-gel glass of CaO-SiO2-P2O5 system with macropores larger than 100 μm was prepared by adding stearic acid as pore former when the sintering was carried out at 700 ℃ for 3 h. The sol-gel porous glass shows an amorphous structure. The diameter of the pore created by pore former varies from 100 to 300 μm, and macroporous glass has a narrow and small pore size distribution in mesoporous scale. The porosity and pore size ofmacroporous bioactive glass can be controlled.     

Isolation and characterization of YNTC-1, a novel Alicyclobacillus sendaiensis strain

A heterotrophic acidothermophilic bacterial strain, YNTC-1, was isolated from an acidic hot spring in Tengchong, Yunan, China. YNTC-1 grows at pH value of 1.5-8.0 and temperature of 40-70 ℃, with optimal pH and temperature at 3.0 and 55 ℃, respectively. The cells of the strain are in shape of short rod, with 1.0-1.2 μm in length and 0.7-0.8 μm in diameter, and with distinct spores at both poles of each cell. The predominant fatty acids in cellular membrane of the strain are C18：1 ω7c. 16s rRNA gene analysis reveals that this strain is closely related to Alicyclobacillus sendaiensis, with over 99% sequence similarity. Based on phenotypic and genotypic analyses, YNTC-1 is identified as a member ofA. sendaiensis. Considering some important morphological and biochemical differences between strain YNTC-1 and A. sendaiensis ATCC 27009T, YNTC-1 may be proposed to be a novel subspecies of A. sendaiensis. However, this viewpoint has to be confirmed by further studies. Co-bioleaching of pyrite and chalcopyrite with strain YN22, Sulfobacillus thermosulfidooxidans, shows that strain YNTC-1 has no evident influence on bioleaching rates of these two sulphide minerals.     

Effect of anions on preparation of ultrafine α-Al2O3 powder

Ultrafine alumina power was obtained by calcining the precursor at 1 200 ℃ for 2 h, which was prepared by homogeneous precipitation method using aluminium salts and urea as raw materials. The effects of anions on the morphology, particle size, surface area and configuration of the precursors were studied. The results show that the reactions of urea with aluminium nitrate and aluminium chloride result in agglomerates gels with bad filtering performance, the morphology is fibrillar. Aluminium sulphate-urea reactions result in the direct formation of amorphous powders with good filtering performance, of which morphology are regular spherical particles with larger granularity and smaller surface area. The reaction of mutual compound of aluminium sulphate and aluminium nitrate with molar ratio of 40:60 with urea can produce precursor with good filtering performance, spherical morphology, and uniform granularity distribution in the particle size range of 2-3 μm.     

高可靠性OTP存储控制器

该文设计了一种OTP存储控制器电路,通过操作OTP存储器指令产生对应不同操作的接口时序,完成对OTP存储器的编程、读取、唤醒、复位、睡眠等操作。同时,在对OTP存储器编程操作中,针对OTP编程易出错的问题,设计了一种编程算法,即对OTP编程地址进行冗余处理,并在编程操作中对同一个地址多次施加脉冲电压,使编程至OTP存储器的数据的正确性急剧提高。嵌入编程算法电路实现了高可靠性的编程算法,有效地控制了OTP存储器的编程操作。因此,本该设计的高可靠性OTP存储控制器解决了访问存储器时容易出现编程错误的问题,提高了访问OTP存储器的可靠性。     

Influence of electromagnetic stirring on microstructure of AZ91-0.8%Ce magnesium alloy

1 INTRODUCTION In recent years, magnesium alloys have been used in the automobile industry to save fuel and lower emission levels, and about 60 different types of components of magnesium alloys have been applied in automobile parts, in which AZ91magnesium alloy (Mg-Al system) approximately accounts for 90%[1?4]. It is well known that grain size has very important effect on material properties. According to Hall-Petch equation, when grain size decreases, the mechanical properties such as…     

Manufacture of high-dispersed W-Cu composite powder by mechano-thermal process

In order to improve the process of co-reduction of oxide powder, a new mechano-thermal process was designed to produce high-dispersed W-Cu composite powder by high temperature oxidation, short time high-energy milling and reduction at lower temperature. The particle size, oxygen content and their sintering abilities of W-Cu composite powder in different conditions were analyzed. The results show that after a quick milling of the oxide powder for about 3-10 h, the reduction temperature of the W-Cu oxide powder can be lowered to about 650 ℃ from 700-750 ℃ owning to the lowering of particle size of the oxide powder. The average particle size of W-Cu powder after reduction at 650 ℃ is about 0. 5μm smaller than that reduced at 750 ℃. After sintering at 1 200℃ for 1 h in hydrogen atmosphere, the relative density and thermal conductivity of final products (W-20Cu) can attain 99. 5% and 210 W ·m-1· K-1 respectively.     

Effect of infiltrating Si on friction properties of C/C composites

In order to improve the friction-wear properties of the C/C composites for aircraft brake pairs, the friction behavior of samples with infiltrating Si was investigated. The influence of Si smearing thickness on friction properties was studied in detail. The results show that with the increase of Si smearing thickness and β-SiC content, the friction coefficient reduces from 0. 40 to 0. 30; the linear wear of stators increases from 2. 0 μm to 18. 9 μm per cycle, and that of rotors increases from 1. 4μm to 22. 6 μm per cycle; mass wear of stators increases from 20. 6 mg to 126. 9 mg per cycle, and that of rotors increases from 13. 7 mg to 166. 2 mg per cycle. On the other hand, when a large number of inhomogeneous β-SiC particulates are performed, friction surfaces of the samples flake off layer by layer and many nicks are observed.     

Preparation and electrical properties of BaPbO3 thin film

BaPbO3 thin films were deposited on Al2O3 substrates by sol-gel spin-coating and rapid thermal annealing. The microstructure and phase of BaPbO3 thin films were determined by X-ray diffractometry, scanning electrons microscopy and energy dispersive X-ray spectrometry. The influence of annealing temperature and annealing time on sheet resistance of the thin films was investigated. The results show that heat treatment, including annealing temperature and time, causes notable change in molar ratio of Pb to Ba, resulting in the variations of sheet resistance. The variation of electrical properties demonstrates that the surface state of the film changes from two-dimensional behavior to three-dimensional behavior with the increase of film thickness. Crack-free BaPbO3 thin films with grain size of 90 nm can be obtained by a rapid thermal annealing at 700 ℃ for 10 min. And the BaPbO3 films with a thickness of 2.5 μm has a sheet resistance of 35 Ω·-1.     

Design of 512-bit logic process-based single poly EEPROM IP

A single poly EEPROM cell circuit sharing the deep N-well of a cell array was designed using the logic process. The proposed cell is written by the FN tunneling scheme and the cell size is 41.26 μm², about 37% smaller than the conventional cell. Also, a small-area and low-power 512-bit EEPROM IP was designed using the proposed cells which was used for a 900 MHz passive UHF RFID tag chip. To secure the operation of the cell proposed with 3.3 V devices and the reliability of the used devices, an EEPROM core circuit and a DC-DC converter were proposed. Simulation results for the designed EEPROM IP based on the 0.18 μm logic process show that the power consumptions in read mode, program mode and erase mode are 11.82, 25.15, and 24.08 μW, respectively, and the EEPROM size is 0.12 mm².     

μ Analysis and μ synthesis for nonlinear robust control systems

A μ analysis and μ synthesis method for nonlinear robust control systems was presented. The nonlinear robust control problem using μ method was described. By means of the nonlinear state feedback and state coordinates transformation, many uncertain nonlinear systems can be transformed as a linear fractional transformation (LFT) on the generalized plant and the uncertainty. Based on the LFT, a linear robust controller can be obtained by the D-K iteration and then a corresponding nonlinear robust control law is constructed. An example was given in the paper. Project supported by the National Natural Science Foundation of China Synopsis of the first author Wu Min, professor, Ph. D, born in 1963, majoring in complex industrial process control, robust control, nonlinear control and expert control.     

Leaching kinetics of low grade zinc oxide ore in NH3-NH4Cl-H2O system

The leaching kinetics of low grade zinc oxide ore in NH3-NH4Cl-H2O system was studied. The effects of ore particle size, reaction temperature and the sum concentration of ammonium ion and ammonia on the leaching efficiency of zinc were examined. The leaching kinetics of low-grade zinc oxide ore in NH3-NH4Cl-H2O system follows the kinetic law of shrinking-core model. The results show that diffusion through the inert particle pores is the leaching kinetics rate controlling step. The calculated apparent activation energy of the process is about 7.057 kJ/mol. The leaching efficiency of zinc is 92.1% under the conditions of ore particle size of 69μm, holding at 80℃ for 60 min, sum ammonia concentration of 7.5 mol/L, the molar ratio of ammonium to ammonia being 2：1, and the ratio （g/mL） of solid to liquid being 1：10.     

Synthesis and photophysical and electrochemical properties of new cyclometalated platinum complex containing oxadiazole ligand

A new cyclometalated platinum complex containing 2, 5-bis（naphthalene-1-yl）-1,3,4-oxadiazole ligand was synthesized and characterized. The UV-Vis absorptions and photoluminescent properties of the ligand and its platinum complex were investigated A characteristic metal-ligand charge transfer absorption peak at 439 nm in the UV spectrum and a strong emission peak at 625 nm in the photoluminescence spectrum were observed for this complex in dichloromethane. Cyclic voltammtry （CV） analysis shows that the EHOMO （energy level of the highest occupied molecular orbital） and ELUMO （energy level of the lowest unoccupied molecular orbital） of the platinum complex are about -5.69 and -3.25 eV, respectively, indicating that the oxadiazole-based platinum complex has a potential application in electrophosphorescent devices used as a red-emitting material.     

Relationship between subsurface damage and surface roughness of ground optical materials

A theoretical model of relationship between subsurface damage and surface roughness was established to realize rapid and non-destructive measurement of subsurface damage of ground optical materials.Postulated condition of the model was that subsurface damage depth and peak-to-valley surface roughness are equal to depth of radial and lateral cracks in brittle surface induced by small-radius(radius≤200 μm)spherical indenter,respectively.And contribution of elastic stress field to the radial cracks propagation was also considered in the loading cycle.Subsurface damage depth of ground BK7 glasses was measured by magnetorheological finishing spot technique to validate theoretical ratio of subsurface damage to surface roughness.The results show that the ratio is directly proportional to load of abrasive grains and hardness of optical materials,while inversely proportional to granularity of abrasive grains and fracture toughness of optical materials.Moreover,the influence of the load and fracture toughness on the ratio is more significant than the granularity and hardness,respectively.The measured ratios of 80 grit and 120 grit fixed abrasive grinding of BK7 glasses are 5.8 and 5.4,respectively.     

Phase transformation of nano-grained W(Co, C) composite powder and its phase constitute

1 INTRODUCTION Nano-grained WC-Co cemented carbides with high toughness and high hardness have drawn extensive attention of hard metal industry[1?2]. There are two key processes for the fabrication of this high performance alloy[3?4]. One is the preparation of nanometer WC-Co composite powders, the other is the effective control of grain growth during sintering. At present, great technical breakthrough has been achieved in the preparation of nanometer powders. The typical methods of na…     

Bi-level programming model for reconstruction of urban branch road network

Considering the decision-making variables of the capacities of branch roads and the optimization targets of lowering the saturation of arterial roads and the reconstruction expense of branch roads, the bi-level programming model for reconstructing the branch roads was set up. The upper level model was for determining the enlarged capacities of the branch roads, and the lower level model was for calculating the flows of road sections via the user equilibrium traffic assignment method. The genetic algorithm for solving the bi-level model was designed to obtain the reconstruction capacities of the branch roads. The results show that by the bi-level model and its algorithm, the optimum scheme of urban branch roads reconstruction can be gained, which reduces the saturation of arterial roads apparently, and alleviates traffic congestion. In the data analysis the arterial saturation decreases from 1.100 to 0.996, which verifies the micro-circulation transportation’s function of urban branch road network. Foundation item: Project(2006CB705507) supported by the National Basic Research and Development Program of China; Project(20060533036) supported by the Specialized Research Foundation for the Doctoral Program of Higher Education of China     

Effects of temperature and initial molar ratio of Na2O to Al2O3 on agglomeration of fine Al（OH）3 seed in synthetic Bayer solution

Fine Al（OH）3 crystals were aggregated from supersaturated aluminate solution in the batch reaction tanks. By means of laser particle size analyzer and scanning electron microscopy, the influences of temperature and initial molar ratio of Na2O to Al2O3 （aK） on agglomeration of fine seed in Bayer process were investigated. The results show that agglomeration is almost finished in 8 h, and seeds with size less than 2 μm are easily aggregated together, and almost disappear in 8 h under the optimal process conditions. In the aluminate solution with the same moderate initial aK, when the reaction temperature reaches 75 ℃, the secondary nucleation does not occur, and the effect of agglomeration is better. And at the same reaction temperature, when the initial aK is 1.62, the initial supersaturation of aluminate solution is moderate, the binders on the surfaces of the seed are enough to maintain the agglomeration process, and the agglomeration degree is better. From SEM images, agglomeration mainly occurs in the fine particles, the combinations among the fine particles are loose and the new formed coarse crystal shapes are irregular.