Effect of ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass addition on the microwave dielectric properties of BaO-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The effect of ZnO-B₂O₃(ZB) glass addition on the sintering behavior, microstructures and microwave dielectric properties of BaO-Nd₂O₃-TiO₂-Bi₂O₃ (BNTB) system was investigated with the aid of X-ray diffraction, scanning electron microscopy and capacitance meter. It is found that the ZB glass addition, acting as a sintering aid, can effectively lower the sintering temperature of BNTB system to 850 °C. The dielectric constant of BNTB-ZB ceramics increases with the increase of soaking time and the value of dielectric loss decreased with increasing soak time. The optical dielectric properties at 1 GHz of ɛ=74, tan δ=4×10⁻⁴, and TCC=25 ppm/°c were obtained for the BNTB system doped with 25 wt% ZB glass sintered at 850 °C for 2 h, representing that the BNTB-ZB ceramics could be promising for multilayer low temperature co-fired ceramics applications.     

Microstructure and mechanical properties of TiB<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites

Effects of Al2O3 and Ni as the additives on the sinterability, microstructure and mechanical properties were systematic studied. The experimental results show that only a relative density about 96.2% of hot-pressing TiB2-30%Al2O3 can be attained due to the plate-like TiB2 particle and its random orientation and excessive Al2O3 grain growth. When sintering temperature is higher than 1 700 ℃, TiB2 grain growth can be found, which obvious improves flexural strength of TiB2 matrix but decreases toughness. It seems that mechanical properties of TiB2-Al2O3 composites are mainly depended on relative density besides grain growth. otherwise, they will be determined by relative density and TiB2 matrix strength together. Anyway, Al2O3 addition can weaken the grain boundary and thus improve the toughness of the materials. A flexural strength of 529 MPa, Vickers hardness of 24.8 GPa and indentation toughness of 4.56 MPa·m1/2 can be achieved inTiB2-30vol% Al2O3.     

Effect of the silicon powder content on the properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiC-Me composites

By means of transient plastic phase process, the Al₂O₃-SiC-Me composites were produced throungh adding metal aluminium and silicon-powder to Al₂O₃-SiC materials. Under the condition of the same content of silicon and aluminium mixed-powder, the effect of silicon powder addition on properties of Al₂O₃-SiC-Me composites was studied by means of XRD and EPMA analyses in the temperature range of 300°–1600°C. The results indicated that the content of metal phase in the sample at 1600°C increases with increasing silicon powder content. At the same time, when the temperature is lower than 1100°C, the strength of samples gradually increases with increasing temperature. However when the temperature is higher than 1100°C, the strength of samples gradually decreases with increasing temperature, and this change is very small. The results also indicated that at the same sintering temperature, the sample with 6% silicon powder has the maximum strength. Supported by the Chen Yunbo Academician Fund (Grant No. 2007CY021)     

Microwave sintering of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript>-WC-Co cermets

Composite powders of nanocrystalline WC-10Co (15wt%),Y2O3 (8mol%) stabilized nanocrystalline ZrO2 (30wt%),industrial cobalt powder (4.5wt%) and submicron Al2O3 (55wt%) composite powders were fabricated by high-energy ball-milling process.The nanocomposite powders were consolidated by microwave sintering process at temperature ranged 1300℃-1550℃ for 15min,respectively.The optimum consolidation conditions,such as temperature,were researched during microwave sintering process.Vickers Hardness of the consolidated cermets was measured by using a Vickers indentation test,and density of specimens was also determined by Archimedes’ principle.Microwave sintering process could not only increase the density of Al2O3-ZrO2-WC-Co cermets and reduce the porosity,but also inhibit abnormal grain growth.     

Effect of MnO<Subscript>2</Subscript> on properties of SiC-mullite composite ceramics for solar sensible thermal storage

For improving the properties of SiC-mullite composite ceramics used for solar sensible thermal storage, MnO₂ was introduced as sintering additive when preparing. The composite ceramics were synthesized by using SiC, andalusite, α-Al₂O₃ as the starting materials with non-contact graphite-buried sintering method. Phase composition and microstructure of the composites were investigated by XRD and SEM, and the effect of MnO₂ on the properties of SiC composites was studied. Results indicated that samples SM1 with 0.2 wt% MnO₂ addition achieved the optimum properties: bending strength of 70.96 MPa, heat capacity of 1.02 J·(g·K)^-1, thermal conductivity of 9.05 W·(m·K)^-1. Proper addition of MnO₂ was found to weaken the volume effect of the composites and improve the thermal shock resistance with an increased rate of 27.84% for bending strength after 30 cycles of thermal shock (air cooling from 1 100 °C to RT).     

Manufacture Process of 8Y2O3 Stabilized ZrO2 from Nano Powders

The manufacture process of 8 mol% Y2O3 stabilized ZrO2 ( YSZ ) from nano powders, including the forming and sintering stages, was studied. During the forming process of YSZ powders, the relative density of YSZ increases lineally with the forming press, and the sintering linear shrinkage of YSZ to the forming press compiles to the parabola trend. When the forming press exceeding 500MPa, the samples with lower shrinkage and high density were obtained. The sintering temperature of YSZ decreases greatly because of the small size and high active surface of YSZ powders. As a result, the beginning sintering temperature of YSZ made in the experiment is as low as 825℃, and the end sintering temperature is 1300-1350℃ . The relative density of YSZ ceramic by solid sintering at 1300-1350℃ is more than 97% , with little and small pores in the uniform microstructure.     

Preparation and properties of crystallizable Glass/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites for LTCC material

The investigated low temperature Co fired ceramics(LTCC) composite of 60wt% CaO-Al2O3-B2O3-SiO2 glass and 40wt% α-Al2O3 as a filler is a non-reactive system, which is a critical part of the low temperature Co fired ceramics process. Through a study on densification process, the phase transformation and microstructure can be revealed. Its composites typically consist of CaO-Al2O3-B2O3-SiO2 glass and α-Al2O3 powders of average particle size (D50=3.49 mm). The sintering behavior, phase evaluation, sintered morphology, and microwave dielectric properties were investigated. In the fire range of 800 to 900 ℃, the composites were crystallized after completion of densification. It is found that the composites start to densify at 825 ℃, simultaneously, the dielectric constant (εr) reaches its maximum. With increasing heat-treatment temperatures, due to the loose microstructure of the material, tanδ increases slightly. The last of the sintered samples were identified as partly Anorthite at 850 ℃. At that temperature it has εr of 7.9 and tanδ less than 1×10-3, and can be used as a promising LTCC material.     

Dielectric properties of Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> ceramics by impedance spectroscopic method

Various lead-free ceramics have been investigated in search for new high-temperature dielectrics. In particular, Bi₄Ti₃O₁₂ is a type of ferroelectric ceramics, which is supposed to replace leadcontaining ceramics for its outstanding dielectric properties in the near future. Ferroelectric ceramics of Bi₄Ti₃O₁₂ made by conventional mixed oxide route have been studied by impedance spectroscopy in a wide range of temperature. X-ray diffraction patterns show that Bi₄Ti₃O₁₂ ceramics are a single-phase of ferroelectric Bi-layered perovskite structure whether it is calcined at 800 °C or after sintering production. This study focused on the effect of the grain size on the electric properties of BIT ceramics. The BIT ceramics with different grain sizes were prepared at different sintering temperatures. Grain becomes coarser with the sintering temperature increasing by 50 °C, relative permittivity and dielectric loss also change a lot. When sintered at 1 100 °C, r values peak can reach 205.40 at a frequency of 100 kHz, the minimum dielectric losses of four different frequencies make no difference, all close to 0.027. The values of E _a range from 0.52 to 0.68 eV. The dielectric properties of the sample sintered at 1 100 °C are relatively better than those of the other samples by analyzing the relationship of the grain, the internal stresses, the homogeneity and the dielectric properties. SEM can better explain the results of the dielectric spectrum at different sintering temperatures. The results show that Bi₄Ti₃O₁₂ ceramics are a kind of dielectrics. Thus, Bi₄Ti₃O₁₂ can be used in high-temperature capacitors and microwave ceramics.     

Low-temperature sintering and microwave dielectric properties of Ba<Subscript>2</Subscript>Ti<Subscript>3</Subscript>Nb<Subscript>4</Subscript>O<Subscript>18</Subscript> ceramics

The effects of CuO and H3BO3 additions on the low-temperature sintering,microstructure,and microwave dielectric properties of Ba2Ti3Nb4O18 ceramics were investigated.The addition of less amount of CuO (< 1 wt%) considerably facilitated the densification of Ba2Ti3Nb4O18 ceramics.Appropriate addition of H3BO3 (< 3.5 wt%) remarkably improved the microwave dielectric properties of ceramics.The addition of H3BO3 and CuO successfully reduced the sintering temperature of Ba2Ti3Nb4O18 ceramics from 1300 to 1050 ℃.B...     

Phase structure and electrical properties of La<Subscript>2</Subscript>O<Subscript>3</Subscript>-doped BiInO<Subscript>3</Subscript>-PbTiO<Subscript>3</Subscript> ceramics with high curie temperature

The phase structure and electrical properties of pure and La2O3-doped Bi-InO3-PbTiO3 （BI-PT） ceramics were studied respectively. In （1 -x）BI-xPT （x=0.72-0.80） ceramics, the stability of tetragonal phase increased with increasing x, and pure perovskite structure was obtained for x=-0.80 ceramics. The phase transition temperature range was between 575 ℃ and 600 ℃ for x=0.72-0.80 ceramics, higher than that of PT （-490 ℃）. The c/a ratio almost linearly decreased with increasing La2O3 content in x-0.80 ceramics. It is believed that Pb^2＋ vacancies were formed by La^3＋ substituting Pb^2＋ in La2O3-doped BI-PT ceramics. Tc shifted to lower temperature by 30 ℃/mol% La2O3. The maximum dielectric constant 8557 around 559 ℃ was exhibited in 0.5mol%-doped BI-0.80PT ceramics. La2O3-doped ceramics could be poled resulting from decreasing of c/a ratio and improving of dielectric loss and resistivity. The maximum piezoelectric coefficient d33 was 12 pC/N for 2mol%-doped BI-0.80PT ceramics.     

Tensile properties of an aluminum matrix composite reinforced by SnO<Subscript>2</Subscript>-coated Al<Subscript>18</Subscript>B<Subscript>4</Subscript>O<Subscript>33</Subscript> whisker

Al18B4O33 whisker was coated by SnO2 particles using a chemical precipitation method, and an aluminum matrix composite reinforced by the coated whisker was fabricated by squeeze casting technique. It is found that the SnO2 coating can react with aluminum matrix during squeeze casting process, and Sn particles are induced near the interface between Al18B4O33 whisker and matrix. The tensile test at room temperature indicated that the tensile strength of Al18B4O33 whisker reinforced aluminum matrix composite can be enhanced by suitable content of SnO2 coating. The composites with various whisker coating contents exhibit maximum tensile plasticity at about 300 ℃, and the composite with a suitable whisker coating content could enhance its tensile plasticity evidently, which suggest that an Al18B4O33 whisker-Al composite with both high strength at room temperature and high formability at elevated temperature can be designed.     

Fabrication and mechanical properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiAl composites

Al₂O₃/TiAl composites were successfully fabricated by hot-press-assisted exothermic dispersion method with elemental powder mixtures of Ti, Al TiO₂ and Nb₂O₅, and the microstructure and mechanical properties were investigated. The results indicate the fine Al₂O₃ particles tend to disperse on the grain boundaries. The grain size of TiAl matrix decreases and the hardness increases with increasing Nb₂O₅ content. The bending strength and fracture toughness reach to a maximum when Nb₂O₅ content is 6 wt%, under 642 MPa and 6.69 MPa·m^1/2, respectively. Based on the fractography and the observation of crack propagation path, it is concluded that the strengthening and toughening of such composites at room temperature can be attributed to the refinement of the TiAl matrix, the deflection behavior in the crack propagation and the dispersion of Al₂O₃ particles.     

Dielectric Properties of B2O3 Doped MgTiO3-CaTiO3 System Ceramics

The dielectric ceramics with a main crystal phase of MGTiO3 and additional crystal phase of CaTiO3 were prepared by the conventional electronic ceramics technology .the strucures of MgTiO3 are ilmenitetype,and belong to hexagonal syngony.the ratio of MgTiO3 to Ca TiO3 doping on the dielectric properties of MGTiO3-CaTiO3(MCT)ceranics were inrestigated.the addition of B2O3 decreases the sintering temperatnre and results in rapid desification without obrious negative effect on the Q values of the system(Q=1/tan ).B2O3 exists as liquid phase in the sintering process,promoting the reactions as a singering agent.     

Microstructures and mechanism of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al composites fabricated by the reaction between SiO<Subscript>2</Subscript> and molten aluminum

Al₂ O₃/Al composite was fabricated by the reaction between SiO₂ and molten aluminum. The microstructures of the composite obtained under different reaction conditions were analyzed. The formation mechanism of the composite microstructure was discussed. Results show that the reaction kinetics is influenced remarkably by the reaction temperature, reaction time and the quantity of SiO₂. The morphologies of Al₂O₃ have different features, depending on the reaction temperature. The composite has equaxed Al₂O₃ grains when materials reacted below 1200°C, and the composite is composed of a large number of fine Al₂O₃ grains and aluninum. The composite has a frame-shaped Al₂O₃ microstructure at the reaction temperature of above 1250°C. CHENG Xiao-min: Born in 1964 Funded by the National Natural Science Foundation of China (No. 91522)     

Direct synthesis of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-modified Li(Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>)O<Subscript>2</Subscript> cathode materials for lithium ion batteries

To improve the cyclic stability at high temperature and thermal stability, the spherical Al₂O₃-modified Li(Ni_0.5Co_0.2Mn_0.3)O₂ was synthesized by a modified co-precipitation method, and the physical and electrochemical properties were studied. The TEM images showed that Li(Ni_0.5Co_0.2Mn_0.3)O₂ was modified successfully with nano-Al₂O₃. The discharge capacity retention of Al₂O₃-modified Li(Ni_0.5Co_0.2Mn_0.3)O₂ maintained about 99% after 200 cycles at high temperature (55 °C), while that of the bare one was only 86%. Also, unlike bare Li(Ni_0.5Co_0.2Mn_0.3)O₂, the Al₂O₃-modified material cathode exhibited good thermal stability.     

Preparation and optical properties of Er<Superscript>3+</Superscript>: Na<Subscript>2</Subscript>O-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> transparent glass-ceramics

Na₂O-Al₂O₃-SiO₂ glass-ceramics doped with Er³⁺ ions were synthesized by the conventional melt quenching technique at a low melting temperature. The samples were characterized by differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis-NIR scanning spectrophotometry, and fluorescence spectrometry. The results show that the main crystalline phase of glass-ceramics is nepheline.The best heat-treatment process is at 520 °C for 2 h. Because the up-conversion luminescence and near infrared luminescence properties of glass doped with Eu³⁺ are studied in detail.     

Investigation on phase evolution of the ZnO-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> glass ceramics

ZnO-B₂O₃-SiO₂-Al₂O₃-Na₂O glass doped with nucleating agent TiO₂ was prepared with melting-quenching method and the effect of nucleating agent on the crystallization behavior and phase evolution of this glass was investigated by differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The experimental results show that the glass transition temperature and the first crystallization temperature decrease from 630 °C and 765 °C to 595 °C and 740 °C, respectively, with introduction of TiO₂ into glass. There is no diffraction peaks in the XRD pattern but it is no longer transparent for the base glass without nucleating agent after heat treatment, which suggests the serious phase separation occurred, and the observation by SEM indicates that the phase separation is developed by nucleation and growth mechanism. However, there are two different crystals ZnAl₂O₄ and NaAlSiO₄ present in the glass containing TiO₂ after heat treating at 575 °C for 2 h and 740 °C for 6 h, respectively. What is interesting is that NaAlSiO₄ disappears as the crystallization time at 740 °C increases from 6 h to 12 h, and more ZnAl₂O₄ crystal is formed, namely, the further formation of ZnAl₂O₄ is at cost of NaAlSiO₄ with increasing crystallization time. And observation of the morphology of glass ceramics shows great difference with increasing crystallization time. Moreover, the ability of ZnO-B₂O₃-SiO₂-Al₂O₃-Na₂O glass ceramics against attacking of 1M HCl solution is increased by the crystals precipitated in heat treatment process.     

Structure,Electrical Conducting and Thermal Expansion Properties of Ln0.6Sr0.4Co0.8Fe0.2O3 （Ln = La,Pr, Nd,Sm） Ceramics

Ln0.6Sr0.4Co0.2Fe0.2O3 （Ln=La, Pr, Nd, Sm） perovskite-type complex oxides were synthesized using a glycine-nitrate process, and the structure, electrical conducting and thermal expansion properties of the resulting ceramics were examined with regard to the nature of the lanthanide cations. The results indicated that the La, Pr and Nd specimens had a rhombohedral symmetry, while an orthorhombic structure was determined for the Sm specimen. The pseudo-cubic lattice constant decreased with smaller lanthanide cations. It was found that the electrical conducting properties declined with decreasing lanthanide cation size. Fortunately, all the compositions remained rather high electrical conductivities exceeding 650 Ω ^-1m·cm^-1 in the intermediate temperature range （600-800 ℃）. An appreciable thermal expansion increase at high temperatures was detected for all the compositions. Decreasing the size of the lanthanide cations resulted in an increase of thermal expansion. With respect to the high electrical conductivities, the Ln0.6Sr0.4Co0.8Fe0.2O3 oxides are considered to be acceptable as mixed conducting component in composite cathode designs together with doped ceria electrolytes.     

Preparation and microstructure of spinel zinc ferrite ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> by Co-precipitation method

Spinel zinc ferrites ZnFe₂O₄, prepared by co-precipitation method using the zinc nitrate Zn(NO₃)₂·6H₂O and ferric nitrate Fe(NO₃)₃·2H₂O as the raw materials, were characterized by the thermo gravimetric analysis (TG) and differential scanning calorimeter (DSC), X-ray diffraction (XRD) and scanning electron microscope (SEM). The influence of synthesis conditions, such as Zn/Fe molar ratio, pH value, the sintering temperature and time, on the microstructures was detailedly investigated. The relationships between the microstructures and the synthesis conditions were discussed. The results show that the pure spinel zinc ferrites ZnFe₂O₄ are formed when the Zn/Fe molar ratio is 1.05:2 at pH=8.5 or Zn/Fe molar ratio is 1:2 at Ph=9-10, and the precursors are sintered at 1100 °C for 4 h. Especially no other phases are observed when the Zn/Fe molar ratio is 1:2 at pH=10 and the precursor is sintered above 700 for 4 °C h. The higher sintering temperature and longer sintering time contribute to grain growth.     

Microstructures and Properties of SiC／Al2O3 ／Al- Si Composites Prepared by Reactive Penetration

The composition, microstructures and properties of SiC/Al2O3/Al-Si composites formed by reactive penetration of the molten aluminum into the preforms of SiO2 and SiC were investigated. The composition of the composites was measured by X-ray diffraction ( XRD ). The microstructures of the composites were also measured by scanning electron microscopy (SEM) and optical microscopy. In addition, the factors affecting the properties of the composites were discussed. The experiments show that the mechanical properties of the composites depend on their relative densities and the sizes of the fillers“ SiC gains“. The denser the SiC/Al2O3/Al-Si composites, the higher their bending strength. As the filler “SiC gains“ become fine, the bending strength of the composites increases.