Ablation behavior of a network interlacing ZrC-VC ceramic coating prepared by a pioneering spillover permeation

A novel network interlacing ZrC-VC ceramic coating was prepared by a pioneering spillover permeation. With the increase of Zr content in the blind vias, the content of ZrC in the coating and the density of the coating all decrease. The density of the coating on C/C–ZrC–SiC substrate is obviously higher than that on C/C substrate. The linear ablation rate of the novel ceramic coated C/C–ZrC–SiC composites was ?0.06 μm/s with about 20 and 1.56 times reduction than C/C composites and C/C–ZrC–SiC composites respectively. The improved ablation resistance was attributed to a dense honeycomb ZrO₂ layer filled with liquid vanadium oxide in the ablation center and the improved thermal radiation.     

涂层工艺对C/C复合材料结构和弯曲性能的影响

采用热处理和包埋工艺制备了Ｃ／Ｃ复合材料的ＭｏＳｉ２／ＳｉＣ抗氧化涂层,对组织结构、界面、弯曲断口进行了显微观察,分析了氧化保护涂层及其工艺对其机械性能的影响,结果表明,该工艺在Ｃ／Ｃ复合材料表面生成涂层的同时,使基材内部的界面也被硅化;并且发现,热解炭基体比炭纤维更易与Ｓｉ反应生成ＳｉＣ。Ｃ／Ｃ复合材料经涂层工艺处理后,弯曲强度降低;热处理过程中发生的材料氧化是弯曲强度下降的主要原因     

Structural characteristics and ablative behavior of C/C–ZrC–SiC composites reinforced with “Z-pins like” Zr–Si–B–C multiphase ceramic rods

In order to improve the ablation and oxidation resistance of C/C–ZrC–SiC composites in wide temperature domain, “Z-pins like” Zr–Si–B–C multiphase ceramic rods are prepared in the matrix. The influence of different sintering temperatures on the microstructure of ceramic rods and the ablative behavior of heterogeneous composites are studied. The results showed that the ZrB₂ and SiC phases are formed in the sintered matrix, and the increase of sintering temperature is beneficial to improve the density of the ceramic rods. The ablation properties of samples have been greatly improved. The mass and linear ablation rate are 0.8 mg/s and 3.85 μm/s, respectively, at an ablation temperature of 3000 °C and an ablation time of 60 s. After ablation, the matrix surface is covered with SiO₂ and ZrO₂ mixed oxide films. This is due to the preferential oxidation of “Z-pins like” Zr–Si–B–C multiphase ceramic rods in the ablation process, and B₂O₃ melt, SiO₂ melt, borosilicate glass, ZrSiO₄ melt and ZrO₂ oxide film can be generated successively from the low-temperature segment to the ultra-high temperature segment. These oxidation products can be used as compensation oxide melts for the healing of cracks and holes on the matrix surface in different temperature ranges and effectively prevent the external heat from spreading into the matrix. Therefore, C/C–ZrC–SiC composites with “Z-pins like” Zr–Si–B–C multiphase ceramic rods achieve ablation resistance in wide temperature domain.     

Microstructure and ablation behavior of SiC coated C/C–SiC–ZrC composites prepared by a hybrid infiltration process

In this study, C/C–SiC–ZrC composites coated with SiC were prepared by precursor infiltration pyrolysis combined with reactive melt infiltration. The pyrolysis behavior of the hybrid precursor was investigated using thermal gravimetric analysis-differential scanning calorimetry, X-ray diffraction, and scanning electron microscopy techniques. The microstructure and ablation behavior of the composites were also investigated. The results indicate that the composites exhibit an interesting structure, wherein a ceramic coating composed of SiC and a small quantity of ZrC covers the exterior of the composites, and the SiC–ZrC hybrid ceramics are partially embedded in the matrix pores and distributed around the carbon fibers as well. The composites exhibit good ablation resistance with a surface temperature of over 2300 °C during ablation. After ablation for 120 s, the mass and linear ablation rates of the composites are 0.0026 g/s and 0.0037 mm/s, respectively. The great ablation resistance of the composites is attributed to the formation of a continuous phase of molten SiO₂ containing SiC and ZrO₂, which seals the pores of the composites during ablation.     

Self‐Generating High‐Temperature Oxidation‐Resistant Glass‐Ceramic Coatings for C–C Composites Using UHTCs

Carbon–carbon (C–C) composites are ideal for use as aerospace vehicle structural materials; however, they lack high‐temperature oxidation resistance requiring environmental barrier coatings for application. Ultra high‐temperature ceramics (UHTCs) form oxides that inhibit oxygen diffusion at high temperature are candidate thermal protection system materials at temperatures >1600°C. Oxidation protection for C–C composites can be achieved by duplicating the self‐generating oxide chemistry of bulk UHTCs formed by a “composite effect” upon oxidation of ZrB₂–SiC composite fillers. Dynamic Nonequilibrium Thermogravimetric Analysis (DNE‐TGA) is used to evaluate oxidation in situ mass changes, isothermally at 1600°C. Pure SiC‐based fillers are ineffective at protecting C–C from oxidation, whereas ZrB₂–SiC filled C–C composites retain up to 90% initial mass. B₂O₃ in SiO₂ scale reduces initial viscosity of self‐generating coating, allowing oxide layer to spread across C–C surface, forming a protective oxide layer. Formation of a ZrO₂–SiO₂ glass‐ceramic coating on C–C composite is believed to be responsible for enhanced oxidation protection. The glass‐ceramic coating compares to bulk monolithic ZrB₂–SiC ceramic oxide scale formed during DNE‐TGA where a comparable glass‐ceramic chemistry and surface layer forms, limiting oxygen diffusion.     

Oxidation behavior of oxidation protective coatings for PIP-C/SiC composites at 1500 °C

Three-dimensional carbon fiber reinforced silicon carbide (C/SiC) composites were fabricated by precursor infiltration and pyrolysis (PIP) with polycarbosilane as the matrix precursor, SiC coating prepared by chemical vapor deposition (CVD) and ZrB₂-SiC/SiC coating prepared by CVD with slurry painting were applied on C/SiC composites, respectively. The oxidation of three samples at 1500 °C was compared and their microstructures and mechanical properties were investigated. The results show that the C/SiC without coating is distorted quickly. The mass loss of SiC coating coated sample is 4.6% after 2 h oxidation and the sample with ZrB₂-SiC/SiC multilayer coating only has 0.4% mass loss even after oxidation. ZrB₂-SiC/SiC multilayer coating can provide longtime protection for C/SiC composites. The mode of the fracture behavior of C/SiC composites was also changed. When with coating, the fracture mode of C/SiC composites became brittle. When after oxidation, the fracture mode of C/SiC composites without and with coating also became brittle.     

Strengthening/toughening of 2D C/SiC composites by coating

SiC and SiC_w/SiC coatings were prepared on two-dimensional carbon fiber reinforced silicon carbide ceramic matrix composites (2D C/SiC), and strengthening/toughening of the composite by the coatings was investigated. After coating, the density of the C/SiC composites was increased effectively and the mechanical properties were improved significantly. Compared with SiC coating, SiC_w/SiC coating showed the more significant effect on strength/toughness of the composites. Coatings had two effects: surface strengthening and matrix strengthening. The latter was the dominant effect. The surface strengthening can increase the crack initiation stress, while the matrix strengthening can enhance the crack propagation resistance. The former effect increased the strength and the latter effect increased the toughness.     

A simple recoating repair methodology to improve oxidation resistance of C/SiCs

ABSTRACT

Lots of through SiC coating micro-cracks appeared due to the mismatch of thermal expansion coefficient between fibres and matrix, and this could be the diffusion path for oxidising gases to reduce oxidation resistance of as-cracked C/SiCs. In this paper, a simple recoating repair methodology was achieved by grinding off original coating and depositing coating again. The experimental results pointed out that as-repaired specimens had excellent oxidation resistance with the whole temperature range of 500–1500°C, and at sensitive point of 800°C, the weight loss rate of the as-repaired specimens was decreased by 22.1% compared to the as-cracked specimens. From 700 to 1100°C, the flexural strength of the as-repaired specimens has obviously improved compared to the as-cracked specimens. Microstructural analysis showed that the recoating repair methodology can seal and narrow through-coating micro-cracks, leading to oxidation resistance and mechanical properties improvement for the as-repaired specimens.     

Preparation and ablation properties of SiC nanowire-reinforced ZrC–SiC coating-matrix integrated C/C composites

A modification of the precursor infiltration pyrolysis (PIP) method was explored to prepare the integrated doped ceramic matrix and coating by the added SiC nanowires layer and shape-stabilization process. The epitaxial layer of SiC nanowires provided surficial attachments for the precursor. And the shape-stabilization process aggregated loose ceramic particles into a coating. Then the SiC nanowire-reinforced ZrC–SiC coating-matrix integrated C/C (S/SZ-CZ/C) composite was simply prepared by the modified PIP method. The bonding strength between the coating and matrix of the S/SZ-CZ/C composite was improved. Through the ablation test, the mass and linear ablation rate of the S/SZ-CZ/C composite were 0.46 mg/s and 0.67 μm/s, which were 60.34 % and 74.91 % lower than those of the SiC nanowire-reinforced C/C–ZrC (S/CZ/C) composite, respectively. The integration of the coating and matrix enabled the formation of a continuous oxide layer of molten SiO₂ and ZrO₂ in the ablation process, which helped to block the oxygen and heat during the ablation test. Thus the ablation resistance of the materials was systematically and effectively improved.     

Effect of temperature gradient on the erosion behavior of SiC coating for carbon/carbon composites in a combustion environment

SiC coating with a thickness of 50–70 µm was prepared on the surface of C/C composites by in-situ reaction method. The SiC coated C/C composites were then tested in a wind tunnel where a temperature gradient from 200 to 1600 °C could be obtained to investigate their erosion behavior. The results of wind tunnel test indicated that the service life of C/C composites was prolonged from 0.5 to 44 h after applying the SiC coating. After the wind tunnel test, three typical oxidation morphologies, including glassy SiO₂ layer, porous SiO₂ layer and clusters of honeycomb-like SiO₂ grains, were found on the SiC coated C/C composites. With the decrease of oxidation temperature, the amount of glassy SiO₂ declined and the thermal stress increased, which induced the cracking followed by the degradation of the SiC coating.     

A novel approach for preparing a SiC coating on a C/C-SiC composite by slurry painting and chemical vapor reaction

In order to improve the oxidation resistance of C/C-SiC composites, a SiC coating was prepared on a C/C-SiC composite by slurry painting combined with a chemical vapor reaction process. The oxidation resistance and microstructural evolution of the coated samples were investigated. The results show that the as-prepared SiC coating contained a large amount of residual silicon, and the presence of these Si promoted the formation of a complete SiO₂ glass layer in the initial stage of oxidation. However, the evaporation of the residual Si also accelerated the failure of the SiC coating, which caused the weight loss of the sample to be about 2.2% after oxidation in static air at 1500 °C for 300 h. Attributed to a large number of SiC ceramics in the C/C-SiC composite, the oxidation weight loss rate of the coating sample after coating failure was reduced.     

A focused review on the tribological behavior of C/SiC composites: Present status and future prospects

Silicon carbide-based ceramic matrix composites have received extensive attention in recent years. Many excellent reviews have reported on the tribological behavior of carbon fiber-reinforced carbon and silicon carbide dual matrix (C/C-SiC) composites. However, a systematic overview of the tribological properties of carbon fiber-reinforced silicon carbide (C/SiC) composites does not exist. This review focuses on C/SiC composites and summarizes the key factors, including internal factors (constituent content, graphitization process, material structure and fiber direction), and various test conditions (pressure and speed, dry and wet, temperature, and counterparts) that affect their tribological behavior. Their wear mechanisms under different conditions are elaborated. Finally, some potential future development directions for improving the performance of C/SiC composites are proposed to provide high-quality ceramic matrix composites for engineering applications. These directions include structural modification, matrix modification, coating technology, laser surface texturing, and material genome method.     

Oxidation protection of C/C composites with a multilayer coating of SiC and Si + SiC + SiC nanowires

An oxidation protective Si–SiC coating with randomly oriented SiC nanowires was prepared on the SiC-coated carbon/carbon (C/C) composites by a two-step technique. First, a porous network of SiC nanowires was produced using chemical vapor deposition. This material was subjected to pack cementation to infiltrate the porous layer with a mixture of Si and SiC. The nanowires in the coating could efficiently suppress the cracking of the coating by various toughening mechanisms including nanowire pullout, nanowire bridging, microcrack deflection and good interaction between nanowire/matrix interface. The results of thermogravimetric analysis and thermal shock showed that the coating had excellent oxidation protection for C/C composites between room temperature and 1500 °C. These results were confirmed by two additional oxidation experiments conducted at temperature of 900 and 1400 °C, which demonstrated that the coating could efficiently protect C/C composites from oxidation at 900 °C for more than 313 h or at 1400 °C for more than 112 h.     

Microstructure and tribological properties of PIP-SiC modified C/C–SiC brake materials

A combination method of precursor infiltration and pyrolysis (PIP), chemical vapor infiltration (CVI) and liquid silicon infiltration (LSI) was proposed to prepare PIP-SiC modified C/C–SiC brake materials. The SiC ceramic matrix pyrolyzed by polymethysilane (PMS) homogeneously dispersed in the fiber bundles region, which improved the plough resistance of local C/C region and the wear resistance of C/C–SiC brake materials. When the braking speed rises to 28 m/s, the fluctuation range of friction coefficient was limited to 0.026. The linear wear rate of the as-prepared composites was could be ~50% less than that of C/C–SiC, when the braking speed was above 15 m/s (for instance, the wear rate of 1.02 μm/(side·cycle) at 28 m/s less than 2.02 μm/(side·cycle) of traditional C/C– SiC). The fading ratio D of CoF under wet conditions was ~11%. The results showed that introducing PIP-SiC could stabilize the braking process and effectively prolong the service life of C/C–SiC brake materials.     

Siliconization elimination for SiC coated C/C composites by a pyrolytic carbon coating and the consequent improvement of the mechanical property and oxidation resistances

Carbon/carbon (C/C) composites have a wide application as the thermal structure materials because of their excellent properties at high temperatures. However, C/C composites are easily oxidized in oxygen-containing environment, which limits their potential applications to a great degree. Silicon carbide (SiC) ceramic coating fabricated via pack cementation (PC) was considered as an effective way to protect C/C composites against oxidation. But the mechanical properties of C/C composites were severely damaged due to chemical reaction between the molten silicon and C/C substrate during the preparation of SiC coating by PC. In order to eliminate the siliconization erosion, a pyrolytic carbon (PyC) coating was pre-prepared on C/C composites by the chemical vapor infiltration (CVI) prior to the fabrication of SiC coating. Due to the retardation effect of PyC coating on siliconization erosion, the flexural strength retention of the SiC coated C/C composites with PyC coating increased from 46.27 % to 107.95 % compared with the specimen without PyC coating. Furthermore, the presence of homogeneous and defect-free PyC coating was beneficial to fabricate a compact SiC coating without silicon phase by sufficiently reacting with molten silicon during PC. Therefore, the SiC coated C/C composites with PyC coating had better oxidation resistances under dynamic (between room temperature and 1773 K) and static conditions in air at different temperatures (1773?1973 K).     

Oxidation behaviour of C/C–SiC brake discs tested on full-scale bench rig

C/C–SiC composites are considered to be strong candidates for the new generation of high-speed train brake discs. To achieve a better application, it is necessary to improve understanding of the oxidation behaviour of C/C–SiC brake discs after a full-scale bench test rig. In this study, full-scale braking bench tests for C/C–SiC self-mated brake pairs were conducted under a braking speed of 350–420 km/h and a braking pressure of 17–28 kN. Moreover, the oxidation behaviour and mechanisms of the C/C–SiC brake discs during the practical braking process were investigated. The results indicate that the oxidation behaviour is highly dependent on the friction surface region of the C/C–SiC brake disc owing to the distribution of microcracks, the formation of friction films, the difference in temperature, and the contact content with O₂. Specifically, the oxidation depths of the friction layer on the inner circumferential surface, middle friction surface, and outer circumferential surface were 278.3, 252.1, and 359.9 μm, respectively. Furthermore, the oxidation reaction preferentially occurs in the active area of the C fibre and pyrolytic carbon (PyC) during the braking process.     

Facile preparation of morph-genetic SiC/C porous ceramic at low temperature by processed bio-template

A porous morph-genetic SiC/C ceramic material was fabricated using biomass-derived C template, Si powder, and Fe(NO₃)₃·9H₂O as the starting materials. The effects of heating temperature, and catalyst/Si mole ratio on the formation of SiC/C ceramic were investigated. In addition, the pore size distribution was obtained through pore size analysis, and the determination of oxidation resistance of SiC/C ceramics and C template was carried out by thermogravimetric analysis. The results show that copious amounts of SiC nanowires, which were distributed on the surfaces and interiors of the C template holes, were formed at 1300 °C with 4 wt% Fe as catalyst. The SiC nanowires significantly affected the oxidation resistance and microporous structures of the prepared materials. Moreover, a possible formation mechanism for the porous SiC/C ceramic was determined.     

Oxidation Protection Coatings for C/SiC based on Yttrium Silicate

The factor which currently precludes the use of carbon fibre reinforced silicon carbide (C/SiC) in high temperature structural applications such as gas turbine engines is the oxidation of carbon fibres at temperatures greater than 400°C. It is, therefore, necessary to develop coatings capable of protecting C/SiC components from oxidation for extended periods at 1600°C. Conventional coatings consist of multilayers of different materials designed to seal cracks by forming glassy phases on exposure to oxygen. The objective of this work was to develop a coating which was inherently crack resistant and would, therefore, not require expensive sealing layers. Yttrium silicate has been shown to possess the required properties for use in oxidation protection coatings. These requirements can be summarised as being low Young’s modulus, low thermal expansion coefficient, good erosion resistance, and low oxygen permeability. The development of protective coatings based on a SiC bonding layer combined with an outer yttrium silicate erosion resistant layer and oxygen barrier is described. Thermodynamic computer calculations and finite element analysis have been used to design the coating. C/SiC samples have been coated using a combination of chemical vapour deposition and slip casting. The behaviour against oxidation of the coating has been evaluated.     

Polymer-metal slurry reactive melt infiltration: A flexible and controllable ceramic modification strategy for irregular C/C components

Herein, we investigate the applicability of the polycarbosilane (PCS)–metal slurry reactive melt infiltration (RMI) process to various metals. The slurry exhibiting the best ceramized ability was used to examine the relationship between the ceramic thickness and reactive time, ceramic thickness and reactive temperature, and infiltration depth and slurry-coating thickness. The results show that the thickness of the ceramic layer increases with reactive time and temperature and the infiltration depth increases with the coating thickness. PCS–Si₉₀Zr₁₀ slurry RMI was selected to modify cylindrical nozzle C/C preforms, and dense C/C–SiC–ZrC composites with a density of ~2.05 g cm⁻³ were obtained. Owing to the good control of the PCS–Si₉₀Zr₁₀ slurry RMI on the interface, matrix, and carbon fiber of the as-received cylindrical composites, the bending strength of the C/C–SiC–ZrC composites was as high as 306.4 MPa, which is considerably higher than that of a C/C preforms (70.4 MPa). Considering the ablation resistance, the mass and linear ablation rates of the C/C–SiC–ZrC composite (~0.29 mg s⁻¹ and ~2.48 × 10⁻³ mm s⁻¹, respectively) were similar to those of the composites prepared using traditional RMI (~0.23 mg s⁻¹ and ~2.29 × 10⁻³ mm s⁻¹). The proposed polymer–metal RMI is more suitable for the modification of C/C preforms with thin-wall structures owing to its advantages including precise control of infiltration dose and flexible operation of slurry coating. Furthermore, it is suitable for the local modification of C/C components.     

Oxidation behavior of C/SiC-SiBCN composites at high temperature

In order to improve the anti-oxidation performance of C/SiC composites at high temperature, C/SiC composites should be modified by self-healing components. SiBCN ceramic is an ideal self-healing component because of excellent oxidation resistance and thermal stability. C/SiC composites were modified by PDC SiBCN ceramic (C/SiC-SiBCN) by using CVI combined with polymer infiltration and on-line pyrolysis (PI-OP). The oxidation behaviors of C/SiC composites fabricated by CVI method and C/SiC-SiBCN composites fabricated by CVI + PI-OP method and CVI + PIP method at different temperatures in air were compared. The results showed that the strength retention ratios of the composites fabricated by the three methods decreased with the increase of temperature. Compared with the samples fabricated by the other two methods, the weight loss of the samples fabricated by CVI + PI-OP method was greater, but the strength retention ratio was higher.